2017 VOLVO V90 seat adjustment

INTRODUCTION
}}
47
Function view with buttons for car functionsAll the buttons for car functions are located in the function view, one of the centre display's basic views. Navigate to the function view fromhome view by swiping from left to right across the screen
10
.Different types of buttonsThere are three different types of buttons for car functions; see below:
Type of button Property Affects car function
Function buttons Have on/off positions. When a function is running, an LED indicator illuminates to the left of the icon for the but- ton. Press the button to activate/deactivate a function. Most buttons in function view are functionbuttons.
Trigger buttons Do not have on/off positions. When a trigger button is pressed, a window for the function opens. For example, it may be awindow for changing a seat's position. •
Camera
•Headrest fold
•
Functions for folding seats
•
Head-up display adjustments
Parking buttons Have on, off and scan modes.
Similar to the function buttons but with an extra position for parking scanning. •Park In
•Park Out
10
Applies to left-hand drive cars. For right-hand drive cars - swipe in the opposite direction.

||
SAFETY
72sitting on the front passenger seat then he/she could suffer serious injury if the airbag deploys. If the passenger airbag is deactivated then rear- facing child seats can be fitted on the front pas-senger seat.
NOTE
Regulations regarding the placement of chil- dren in cars vary from country to country.Check what does apply.
WARNING
Never allow anybody to stand or sit in front of the front passenger seat. Never use a rear-facing child seat on the front passenger seat if the airbag is activated. Front-facing passengers (children and adults) must never sit on the front passenger seat ifthe passenger airbag is deactivated. Failure to follow the advice given above can endanger life or lead to serious personalinjury.
Child seat installationThe following points are important to consider when a child seat is being fitted in the car.
WARNING
Booster cushions/child seats with steel braces or some other design that could reston the seatbelt buckle's opening button mustnot be used, as they could cause the seatbeltbuckle to open accidentally. Do not secure the straps for the child seat into the seat's horizontal adjustment bar or insprings, rails or beams under the seat. Sharpedges may damage the straps. Do not allow the upper section of the child seat to rest against the windscreen.
Installation in the front seat
•
When fitting rear-facing child seats, check that the passenger airbag is deactivated.
• When fitting front-facing child seats, checkthat the passenger airbag is activated.
• Only use child seats that are recommendedby Volvo, are universally approved or aresemi-universal, and where the car is includedon the manufacturer's vehicle list.
• ISOFIX child seats can only be fitted when the car is equipped with the ISOFIX console 2
accessory.
• If the child seat is equipped with lower straps, Volvo recommends that the lower mounting points are used with these 2
. •
The ISOFIX guide can be used in order to facilitate child seat installation.
Installation in the rear seat
•Only use child seats that are recommended by Volvo, are universally approved or aresemi-universal, and where the car is includedon the manufacturer's vehicle list.
• A child seat with support legs must not befitted in the centre seat.
• The outer seats are equipped with theISOFIX fixture system and are approved for i- Size3
.
• The outer seats are equipped with upper mounting points. Volvo recommends thatchild seat's upper straps should be pulledthrough the hole in the head restraint beforebeing tensioned at the mounting point. If thisis not possible, follow the recommendationsfrom the child seat manufacturer.
• If the child seat is equipped with lowerstraps, never adjust the position of the seatin front after the straps have been fitted inthe lower mounting points. Always rememberto remove the lower straps when the childseat is not installed.
2
The accessory range varies depending on market.
3 Varies depending on market.

||
INSTRUMENTS AND CONTROLS
* Option/accessory.
88
Display/function/control
Right-hand steering wheel keypad
Display lighting, unlocking the tailgate, opening/closing the tailgate *
Bonnet opening
Horn
Steering wheel adjustment
Left-hand steering wheel keypad
Display/function/control
Front reading lamps and interior lighting
Panorama roof*
Display in roof console
Manual dimming of interior rearview mir- ror
Display/function/control
Centre display
Hazard warning flashers, max defroster/ heated windscreen *, media, glovebox
door opening
Gear selector
Display/function/control
Ignition dial
Drive mode control *
Parking brake
Automatic braking when stationary
Display/function/control
Memory for setup of:
• power front seat
*
• Door mirrors
• Head-up display
*
Door opening, locking/unlocking of side doors and tailgate

||
INSTRUMENTS AND CONTROLS
* Option/accessory.
114
Adjusting brightness and vertical position
1.
Press the Head-up display adjustmentsbutton in the function view in the centre dis- play.
2. Adjust the brightness and vertical position of the projected image in the driver's field ofvision using the steering wheel's right-handkeypad.
Reducing the brightness
Increasing the brightness
Raising the position
Lowering the position
Confirm
The brightness of the graphics is automatically adapted to their background light conditions. Thebrightness is also affected by the adjustment ofthe brightness in the car's other displays. The vertical position can be stored in the memory function of the power front seat *.
Calibrate the horizontal position
The head-up display's horizontal position may need to be calibrated if the windscreen or displayunit is replaced. Calibration means that the pro-jected image is rotated clockwise or anticlock-wise. 1.
Tap on
Settings in the centre display's top
view.
2. Select
My CarDisplaysHead-Up
Display Calibration.
3. Calibrate the image's horizontal position with the steering wheel's right keypad.
Rotate anticlockwise
Rotate clockwise
Confirm
CleaningGently wipe the display's cover glass with a clean and dry microfibre cloth. If necessary, lightly mois-ten the microfibre cloth. Never use strong stain removers. A special clean- ing agent available from Volvo dealers can beused for more difficult cleaning.
When replacing the windscreenCars with head-up display are equipped with aspecial type of windscreen that meets therequirements for displaying the projected image.

INSTRUMENTS AND CONTROLS
* Option/accessory.121
Manual front seat
The car's front seats have different setting options for optimum seating comfort.
Raise/lower the front edge of the seat cush- ion * by pumping up/down.
Change the length of the seat cushion by pulling the lever up and moving the seatcushion forward/backward by hand.
Adjust the seat forward/backward by lifting the handle and adjusting the distance to thesteering wheel and pedals. Check that theseat is locked after the position has beenadjusted.
Change the lumbar support * by pressing the
button upward/downward/forward/back.
Raise/lower the seat by means of adjusting the control up/down.
Change the backrest rake by turning the control knob.
WARNING
Adjust the position of the driver's seat before setting off, never while driving. Make sure thatthe seat is in locked position in order to avoidpersonal injury in the event of heavy brakingor an accident.
Related information
• Power front seat
* (p. 121)
• Multi-functional front seat
* (p. 123)
• Activating/deactivating heating of the seats
*
(p. 203)
• Seatbelt (p. 59)
Power front seat
*
The car's front seats have different setting options for optimum seating comfort. The powerseat can be moved forward/backward and up/down. The front edge of the seat cushion can beraised/lowered and the backrest rake can bechanged. The lumbar support can be adjustedupward/downward/forward/backward.
The power seats have overload protection which is tripped if a seat is blocked by an object. If thishappens, remove the object and then operate theseat again. The seat can be adjusted for a period of time after unlocking the door without the engine run-ning. Seat adjustment can always be performedwhen the engine is running. Adjustment can alsobe performed for a period of time after theengine has been switched off.
Related information
• Multi-functional front seat
* (p. 123)
• Adjusting the power front seat
* (p. 122)
• Using the memory function in the power front seat
* (p. 122)
• Manual front seat (p. 121)
• Activating/deactivating heating of the seats
*
(p. 203)

INSTRUMENTS AND CONTROLS
}}
* Option/accessory.123
3.
Within three seconds, depress the 1 or 2
button.
> When the position has been stored in the selected memory button an acoustic sig- nal sounds and the light indicator in the M
button extinguishes.
If none of the memory buttons is depressedwithin three seconds then the M button extin-
guishes and no storing takes place. The seat must be adjusted again before a new memory can be set.
Using a stored settingA stored setting can be used with the front dooreither open or closed:
Open front door
–Depress one of the memory buttons 1 or 2
with a short press. Seat, door mirrors and head-up display move and then stop at thepositions stored in the selected memory but-ton.
Closed front door
–Hold one of the memory buttons 1 or 2
depressed until seat, door mirrors and head- up display stop in the positions that arestored in the selected memory button.
If the memory button is released, the movementof the seat, door mirrors and head-up display willbe stopped.
WARNING
Risk of crushing! Make sure that children do not play with the keypad. Check that there areno objects in front of, behind or under theseat during adjustment. Make sure that noneof the passengers in the rear seat is in dangerof becoming trapped.
Related information
• Power front seat
* (p. 121)
• Adjusting the power front seat
* (p. 122)
Multi-functional front seat *
Enhance the seating comfort using the multi- function control.
Multi-function control, located on the side of the seat's seating section.
The multi-function control can, in some variants, be used to adjust the lumbar support *, side sup-
port *, cushion length and massage settings *. Set-
tings made with the multi-function control areshown in the centre display *. Certain function
selections can also be made directly in the centre display.
Centre displayThe driver and the passenger seat settings thatare made with the multi-function control areshown in the centre display. If the settings foronly one of the front seats are shown in the cen-tre display, the settings are positioned centred in

INSTRUMENTS AND CONTROLS
}}
* Option/accessory.127
View for extension of the cushion in the centre display.
1. Activate the multi-function control by turning
the control upward/downward. The seat set- tings view will be shown on the centre dis-play.
2. Select
Cushion extension in the seat set-
tings view.
• Press the front seat button in order to extend the seat cushion.
• Press the rear seat button in order toretract the seat cushion.
Related information
•
Multi-functional front seat
* (p. 123)
• Managing messages saved from the driverdisplay and centre display (p. 110)
Adjusting the passenger seat from the driver's seat
*
The front passenger seat can be adjusted from the driver's seat.
Activating the functionThe function can be activated in two ways via the centre display:
Via the function view
Press the Adjust passenger
seat button to activate.
Via settings
1. Press Settings in the top view.
2. Press
My CarSeats.
3. Select
Adjust Passenger Seat From
Driver Position to activate.
Adjust passenger seatFrom activation of the function, the driver must adjust the passenger seat within 10 seconds. Ifno adjustment is made within this time the func-tion is deactivated. The driver adjusts the passenger seat using the controls on the driver's seat:

INSTRUMENTS AND CONTROLS
* Option/accessory.
130
Lowering the backrests in the rear seat
The rear seat's backrest is divided into two parts. The two parts can be lowered forwardindividually.
WARNING
Adjust the seat and fix it before driving away. Take care when adjusting the seat. Uncontrol-led or careless adjustment can lead to trap-ping injuries.
IMPORTANT
There must be no objects on the rear seat when the backrest is to be folded down. Theseat belts must not be connected either. Oth-erwise there is a risk of damaging the rearseat upholstery.
IMPORTANT
The integrated booster cushions * on the
outer seats must be lowered before lowering the seat. The armrest * for the centre seat must be
raised before lowering the seat. If the car has private locking, the tailgate must be closed before lowering the seat.
NOTE
The front seats may need to be pushed for- wards, and/or the backrests adjustedupwards, in order that the rear backrests canbe fully folded forward.
Lowering the backrest
Car with electronic folding
If the car is equipped with electronic folding of the rear seat * there are buttons located in the
cargo area. The backrests can also be lowered manually.
WARNING
Pay attention that people are not at risk of being trapped during the automatic folding ofthe rear seat. Since this takes place automati-cally on the press of a button, no one must beon or too close to the rear seat.
For electronically controlled folding of backrests:
1. Ensure that there are no occupants or objects in the rear seat.
2. Lower the centre seat's head restraint man- ually.
3. Hold the button for folding depressed. The buttons are marked L and R for left and right backrest section respectively.
4. The backrests are lowered automatically to horizontal position. The head restraints arealso lowered automatically.
To facilitate folding of the rear seat, the car mustbe stationary and the tailgate open. To lower the backrest manually: