2017 Peugeot 208 tailgate

40
Central locking
This function allows the doors and boot to be
locked or unlocked simultaneously from inside
the vehicle.
Locking
F Press this button.
This locks the doors and the boot.The indicator lamp comes on.
If one of the doors is open, the central
locking from the inside does not take
place.
Release
F Press this button again. The indicator lamp goes off. When locking / deadlocking from the
outside
When the vehicle is locked or deadlocked
from outside, the switch does not operate.
F

A
fter normal locking, pull one of the
interior door levers to unlock the
vehicle.
F
A
fter deadlocking, it is necessary to
use the remote control, or the key to
unlock the vehicle.
Automatic central locking
The doors lock automatically while driving
(speed above 6 mph [10 km/h]).
F

T
o activate or deactivate this
function (activated by default),
press this button until a buzzer
sounds and/or a message
appears in the screen.
Driving with the doors locked may render
access by the emergency services to the
interior difficult in an emergency.
Boot
Opening
Unlock the vehicle.
F

P

ress the tailgate opening button to
release it, and then guide it open.
Closing
F Lower the tailgate using the interior grab handle.
F

I
f necessary, press down on the tailgate to
fully close it.
Access

41
Boot still open
With the engine running, this is
signalled by:
-

t
his warning lamp coming on,
-

a
n alert message displayed for
a few seconds.
Vehicle moving (speed above 6
mph
(10

km/h)), this is signalled by:
-

t

his warning lamp coming on,
-

a

n alert message displayed for a few
seconds,
-
an

audible signal.
Back-up release
System for mechanically unlocking the boot in
the event of a battery or central locking fault.
Release
F Fold back the rear seats to gain access to the lock from inside the boot. F

I
nsert a small screwdriver into hole A of the
lock to unlock the tailgate.
F
M
ove the latch to the left.
Alarm
The alarm provides the following types of
monitoring:
- Perimeter monitoring
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a
door, the boot, the bonnet, etc.
- Volumetric monitoring
The system checks for any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks a
window, enters the passenger compartment or
moves inside the vehicle.
- Anti-tilt (GTi version)
The system checks for any change in the
attitude of the vehicle.
The alarm is triggered if the vehicle is lifted,
moved or knocked.
2
Access

130
In bad or wintry weather, ensure that the
sensors are not covered with mud, ice or
snow.
The system will be deactivated
automatically if a trailer is being towed or if
a bicycle carrier is fitted (vehicle fitted with
a towbar or bicycle carrier recommended
by PEUGEOT).
The parking sensor system cannot in
any circumstances replace the need for
vigilance on the part of the driver.Reversing camera
The reversing camera is activated automatically
when reverse gear is engaged.
The image is displayed on the touch screen.
The reversing camera function may be
supplemented with parking sensors.They are represented by lines marked "on
the ground" and do not allow the position of
the vehicle to be determined relative to tall
obstacles (for example: other vehicles, etc.).
Some deformation of the image is normal.
The blue lines represent the general direction
of the vehicle (the gap represents the width of
your vehicle except for the door mirrors).
The red lines represent a distance of about
30
cm beyond the edge of your vehicle's rear
b u m p e r.
The green lines represent distances of about 1
and 2 metres beyond the edge of your vehicle's
rear bumper.
The superimposed representation of guide
lines helps with the manoeuvre. The reversing camera cannot, in any
circumstances, replace the need for
vigilance on the part of the driver.
High pressure jet wash
When washing your vehicle, do not direct
the lance within 30
cm of the camera lens.
Opening the tailgate causes the display to
disappear.
Clean the reversing camera regularly
using a soft, dry cloth.
Driving

155
Refilling
Important: if your vehicle's AdBlue®
tank is completely empty – which is
confirmed by the alert messages and the
impossibility of starting the engine – you
must add at least 4

litres and no more than
10


litres. F

A
fter emptying the container or bottle, wipe
away any spillage around the tank filler
using a damp cloth.
If any fluid is spilt or splashed, wash
immediately with cold water or wipe with a
damp cloth.
If the fluid has crystallised, clean it off
using a sponge and hot water.
After refilling
Through the boot (1.6 litre
BlueHDi Euro 6.1)
F Refit the blue cap to the tank filler and turn it
a 6th of a turn clockwise, to its stop.
F
R
efit the black cap and turn it a quarter of a
turn clockwise without pressing. Check that
the cap indicator lamp is facing the support
indicator lamp.
F

D

epending on equipment, return the spare
wheel and/or the storage box to the bottom
of the boot.
F

R

efit the boot carpet and close the tailgate.
Through the fuel filler flap
(1.5 litre BlueHDi Euro 6.2)
F Refit the blue cap to the tank filler and turn it
a 6th of a turn clockwise, to its stop.
F
C
lose the fuel filler flap.
F

O

btain an AdBlue
® container or bottle. After
first checking the use-by date, read the
instructions on the label carefully before
pouring the contents of the container or
bottle into your vehicle's AdBlue
® tank.
7
Practical information

172
Licence plate lamps
For easier removal, per form this procedure with
the tailgate half open.
F
I
nsert a thin screwdriver into the cut-out
located outside the lens.
F

P
ush it outwards.
F

R
emove the lens.
F

C
hange the faulty bulb.
To refit, press on the lens to clip it in place.
Foglamp
For access, pass your hand under the bumper.
F T urn the bulb holder a quarter turn and pull
it out.
F

D
isconnect the lamp unit connector.
F

P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
To replace this type of bulb, you can also
contact a PEUGEOT dealer or a qualified
workshop.
Changing a fuse
Access to the tools
The extraction tweezers are fitted to the back
of the dashboard fusebox cover or glovebox.
Dashboard
F Unclip the cover by pulling at the top left, then right.
F

D
isengage the cover completely and turn it
ove r.
F

R
emove the carrier on which the tweezers
are fitted.
In the event of a breakdown