2017 Peugeot 208 spare wheel

3
.
.
Eco-driving 104
Driving recommendations 1 05
Starting – Switching off the engine

1
08
Parking brake

1
10
Manual gearbox
1

11
Electronic gearbox
1

12
Automatic gearbox

1
14
Gear shift indicator

1
16
Hill start assist

1
17
Stop & Start

1
18
Speed limiter
1

21
Cruise control

1
23
Memorising speeds
1

26
Active City Brake

1
27
Parking sensors
1

29
Reversing camera
1

30
Park Assist

1
31
Under-inflation detection
1

35Fuel tank
1 38
Misfuel prevention (Diesel) 1 39
Compatibility of fuels
1

40
Snow chains

1
41
Towing a trailer

1
42
Load reduction mode

1
43
Energy economy mode
1

43
Changing a window wiper
1

44
Fitting roof bars

1
44
Bonnet


145
Engines


147
Checking levels

1
48
Checks
15

0
AdBlue
® (BlueHDi engines) 1 52
Advice on care 1 56
Warning triangle
1

57
Running out of fuel (Diesel)

1
57
Temporary puncture repair kit
1

58
Spare wheel

1
62
Changing a bulb
1

67
Changing a fuse
1

72
12

V battery
1
78
To w i n g


181
Characteristics of engines and towed loads 18 4
Pe
trol engines
1 85
Diesel engines
1

88
LPG engines
1

90
Dimensions
1

91
Identification markings
1

92
Driving Practical information
In the event of a breakdown Technical data
Alphabetical index
Audio equipment and telematics
PEUGEOT Connect Nav
PEUGEOT Connect Radio
Audio system / Bluetooth
Audio system
.
Contents

105
Observe the recommendations
on maintenance
Check the tyre pressures regularly, when cold,
referring to the label in the door aperture,
driver's side.
Carry out this check in particular:
-
b
efore a long journey,
-

a
t each change of season,
-

a
fter a long period out of use.
Do not forget the spare wheel and the tyres on
any trailer or caravan.
Have your vehicle ser viced regularly (engine
oil, oil filter, air filter, cabin filter, etc.) and
obser ve the schedule of operations in the
manufacturer's service schedule.
With a BlueHDi Diesel engine, if the SCR
system is faulty, your vehicle becomes
polluting. Visit as soon as possible a
PEUGEOT or a qualified workshop to make
your vehicle’s level of nitrogen oxide emissions
compliant to the standard.
When filling the tank, do not continue after the
3
rd cut-off of the nozzle to avoid over flow. At the wheel of your new vehicle, it is only after
the first 1,800
miles (3,000 kilometres) that you
will see the fuel consumption settle down to a
consistent average.
Driving recommendations
Observe the driving regulations and remain
vigilant whatever the traffic conditions.
Pay close attention to the traffic and keep your
hands on the wheel so that you are ready to
react at any time to any eventuality.
As a safety measure, the driver should only
carry out any operations that require close
attention when the vehicle is stationary.
On a long journey, a break every two hours is
strongly recommended.
In bad weather, drive smoothly, anticipate the
need to brake and increase the distance from
other vehicles.
Never leave the engine running in
an enclosed area without adequate
ventilation: internal combustion engines
emit toxic exhaust gases, such as carbon
monoxide. There is a risk of poisoning and
death!
In very severe wintry conditions
(temperatures below -23°C), to guarantee
correct operation and the longevity of
the mechanical elements of your vehicle,
engine and gearbox, the engine must be
left running for 4
minutes before driving.
6
Driving

135
Under-inflation detection
This system automatically monitors the tyre
pressure while driving.
The system monitors the pressure in all four
tyres, once the vehicle is moving.
It compares the information given by the
wheel speed sensors with reference values,
which must be reinitialised after ever y tyre
pressure adjustment or wheel change.
The system triggers an alert as soon as it
detects a drop in the pressure of one or more
tyres.
The tyre under-inflation detection system
does not replace the need for vigilance on
the part of the driver.
This system still requires you to check the
tyre inflation pressure (including the spare
wheel) every month as well as before a
long journey.
Driving with under-inflated tyres impairs
handling, extends braking distances and
causes early tyre wear, particularly in
adverse conditions (heavy loads, high
speeds, long journeys). Driving with under-inflated tyres
increases fuel consumption.
The tyre pressure specifications for your
vehicle can be found on the tyre pressure
label.
For more information on Identification
markings , including in particular the tyre
pressure label, refer to the corresponding
section.
Tyre pressures should be checked when
the tyres are "cold" (vehicle stopped for
1
hour or after a journey of less than
6
miles (10 km) at moderate speeds).
In the contrary case(hot), add 0.3
bar to
the values indicated on the label.
Under-inflation alert
This is indicated by fixed illumination
of this warning lamp, an audible
signal and, depending on the
equipment installed, a message
displayed on the screen.
F

R

educe speed immediately, avoid excessive
steering movements and sudden braking. The loss of pressure detected does not
always cause visible bulging of the tyre.
Do not be satisfied with just a visual
check.
F
I
n the event of a puncture, use the
temporary puncture repair kit or the spare
wheel (depending on equipment),
or
F
i
f you have a compressor, such as the one
in the temporary puncture repair kit, check
the pressures of the four tyres when cold,
or
F
i
f it is not possible to make this check
immediately, drive carefully at reduced
speed.
The alert is kept active until the system is
reinitialised.
The under-inflation alert can only be relied
on if the reinitialisation of the system has
been done with the pressures in the four
tyres correctly adjusted.
F

S
top the vehicle as soon as it is safe to do
so.
6
Driving

141
Snow chains
In wintry conditions, snow chains improve
traction as well as the behaviour of the vehicle
when braking.The snow chains must be fitted only to the
front wheels. They must never be fitted to
"space-saver" type spare wheels.
Take account of the legislation in force
in your country on the use of snow
chains and the maximum running speed
authorised.
Installation tips
F If you have to fit the chains during a journey, stop the vehicle on a flat sur face on the side
of the road.
F

A
pply the parking brake and if necessary
put wheel chocks against the wheels to
prevent your vehicle from sliding.
F

F
it the chains following the instructions
provided by the manufacturer.
F

M
ove off gently and drive for a few seconds,
without exceeding 30
mph (50 km/h).
F

S
top your vehicle and check that the snow
chains are correctly tightened.
It is strongly recommended that before
you leave, you practise fitting the snow
chains on a level and dry sur face.
Avoid driving with snow chains on roads
that have been cleared of snow, to avoid
damaging your vehicle's tyres and the
road sur face. If your vehicle is fitted with
alloy wheels, check that no part of the
chain or its fixings is in contact with the
wheel rim.
Travelling abroad
Cer tain fuels could damage the engine
of your vehicle.
In cer tain countries, the use of a
par ticular fuel may be required
(specific octane rating, specific trade
name, etc.) to ensure correct operation
of the engine.
For any additional information, contact a
dealer.
7
Practical information

154
Topping up with AdBlue®
If you wish to top up yourself, please read
the following warnings carefully.
In cold weather, before per forming the top-up
ensure that the temperature is above -11°C.
Otherwise the AdBlue
® may be frozen and so
cannot be poured into the tank.
Park your vehicle in a warmer area for a few
hours to allow the top-up to be carried out.
F

B

efore topping up, ensure that the vehicle is
parked on a flat and level sur face.
F

S

witch off the ignition to stop the engine
and remove the key from the switch.
Access through the boot (1.6 litre
B lueHDi Euro 6.1)
F Raise the boot carpet then, depending on
equipment, lift out the spare wheel and/or
the storage box.
F

W
ithout pressing, turn the black cap a
quarter turn anti-clockwise and lift it off.
F

T
urn the blue cap a 6
th of a turn anti-
clockwise.
F

L

ift off the cap.
Access through the fuel filler flap
(1.5 litre BlueHDi Euro 6.2)
F With the vehicle unlocked, open the fuel
filler flap; the blue filler cap for the AdBlue®
tank is located to the right of the black fuel
filler cap.
F

T
urn the blue cap a 6
th of a turn anti-
clockwise.
F

R

emove the blue cap.
Practical information

155
Refilling
Important: if your vehicle's AdBlue®
tank is completely empty – which is
confirmed by the alert messages and the
impossibility of starting the engine – you
must add at least 4

litres and no more than
10


litres. F

A
fter emptying the container or bottle, wipe
away any spillage around the tank filler
using a damp cloth.
If any fluid is spilt or splashed, wash
immediately with cold water or wipe with a
damp cloth.
If the fluid has crystallised, clean it off
using a sponge and hot water.
After refilling
Through the boot (1.6 litre
BlueHDi Euro 6.1)
F Refit the blue cap to the tank filler and turn it
a 6th of a turn clockwise, to its stop.
F
R
efit the black cap and turn it a quarter of a
turn clockwise without pressing. Check that
the cap indicator lamp is facing the support
indicator lamp.
F

D

epending on equipment, return the spare
wheel and/or the storage box to the bottom
of the boot.
F

R

efit the boot carpet and close the tailgate.
Through the fuel filler flap
(1.5 litre BlueHDi Euro 6.2)
F Refit the blue cap to the tank filler and turn it
a 6th of a turn clockwise, to its stop.
F
C
lose the fuel filler flap.
F

O

btain an AdBlue
® container or bottle. After
first checking the use-by date, read the
instructions on the label carefully before
pouring the contents of the container or
bottle into your vehicle's AdBlue
® tank.
7
Practical information

162
Spare wheel
Access to the tools
List of tools
1.Wheelbrace.
For removing the wheel trim and the
wheel fastening bolts.
2. Jack with integrated crank.
Used to raise the vehicle.
3. "Bolt cover" tool.
For removing the bolt protectors (covers)
on alloy wheels.
4. Socket for the security bolts.
For adapting the wheelbrace to the
special "security" bolts.
5. Towing eye.
For more information on To w i n g , refer to
the associated section.
The tools are installed in the boot under the
f l o o r.
To gain access:
F

o

pen the boot,
F

l

ift the floor and remove it,
F

r

emove the carrier box containing the tools. All of these tools are specific to your
vehicle and may vary depending on the
level of equipment.
Do not use them for any other purposes.
The jack must only be used to change
a wheel with a damaged or punctured tyre.
Do not use any jack other than the one
supplied with this vehicle.
If the vehicle does not have its original
jack, contact a PEUGEOT dealer or a
qualified workshop to obtain the correct
jack for it.
The jack meets European standards,
as defined in the Machinery Directive
2006/42/EC.
The jack does not require any
maintenance.
Procedure for changing a damaged wheel with
the spare wheel using the tools provided with
the vehicle.
Wheel with hub cap
When refitting the wheel, refit the hub
cap starting by placing its notch facing the
valve and press around its edge with the
palm of your hand.
In the event of a breakdown

163
Taking out the wheel
F Unscrew the central nut.
Putting the wheel back in place
F Put the wheel back in its housing.
F
G
ive the bolt a few turns to loosen it.
F

P
osition the fixing parts (nut and bolt) in the
middle of the wheel.
F

T
ighten fully until the central nut clicks, to
retain the wheel correctly. F

P
ut the box back in place in the centre of
the wheel and clip it.
If there is no wheel in the well, the
fastening device (nut and bolt) cannot be
refitted.
Access to the spare wheel
The spare wheel is installed in the boot under
t h e f l o o r.
According to country, the spare wheel may be
steel, alloy or of the "space-saver" type. F

R
emove the fixing parts (nut and bolt).
F
R
aise the spare wheel towards you from the
r e a r.
F
T
ake the wheel out of the boot.
8
In the event of a breakdown