2017 Peugeot 208 ESP

168
C. GTi model
1.Main beam headlamps (H7- 55W).
2. Dipped beam headlamps (H7- 55W).
3. Daytime running lamps / sidelamps
(light emitting diodes – LEDs).
4. Direction indicators (light-emitting
diodes – LEDs).
5. Front foglamps (directional according
to version) (H11- 55W).
Direction indicators
Quicker flashing of the direction indicator
lamp (left or right) indicates that one of
the bulbs on the corresponding side has
failed.
F

T
urn the bulb holder a quarter turn and pull
it out.
F

P
ull out the bulb and replace it.
To reassemble, proceed in reverse order.
Amber colour bulbs, such as the direction
indicators, must be replaced by bulbs with
identical colour and specifications.
To refit, close the protective cover very
carefully to guarantee the leak-tightness
of the lamp.
Dipped beam headlamps
F Remove the protective cover by pulling on the tab.
F

D
isconnect the bulb connector.
F

S
pread the spring to release the bulb
(model A ).
F

P
ull the bulb out and change it.
To reassemble, carry out these operations in
reverse order, positioning the alignment lug at
the bottom (model A ) or at the top (model B ).
In the event of a breakdown

171
5.Foglamp (P21W).
Light- emitting diodes – LEDs
For replacement, contact a PEUGEOT
dealer or a qualified workshop.
Reversing lamps and direction
indicators
These two bulbs are changed from inside the
boot:
F

O
pen the boot. F

R
emove the access grille from the
corresponding side trim panel.
F
U
nscrew and remove the nut.
F
D
isconnect the lamp unit connector.
F
U
nclip the lamp unit and carefully extract it
pulling straight towards you.
F
P
ress the four tabs and remove the bulb
h o l d e r.
F

T
urn the bulb a quarter turn, pull it out and
fit a new bulb. To reassemble, proceed in reverse order.
Make sure to engage the lamp unit in its guides
while keeping it in line with the vehicle.
Tighten sufficiently to ensure sealing, but
without damaging the lamp.
Third brake lamp
F Unscrew the fixing pins on each side of the
lamp, without removing them completely.
F

P
ush on the screws to unclip the lamp unit.
F

D
isconnect the lamp unit connector.
F

R
emove the lamp unit from the outside.
F

T
urn the bulb holder corresponding to the
faulty lamp a quarter turn and pull it out.
F

P
ull the bulb out and change it.
To reassemble, proceed in reverse order.
8
In the event of a breakdown

173
Glove box
F Open the glove box lid.
F U nclip the fusebox cover by pulling at the
top right.
F

D
isengage the cover completely and turn it
ove r.
F

R
emove the carrier on which the tweezers
are fitted. Before changing a fuse, it is necessary that:
F

t
he vehicle must be stationary with the
ignition off,
F
s
witch off all electrical consumers,
F
t
he defective fuse must be identified using
the allocation tables and the diagrams in the
following pages.
To work on a fuse, you must:
F
u
se the special tweezers to extract the fuse
from its housing and check the condition of
its filament,
F
a
lways replace the defective fuse with a
fuse of the same rating (same colour); using
a different rating could cause a malfunction
(risk of fire).
If the fault recurs after replacing a fuse, have
the electrical system checked by a PEUGEOT
dealer or a qualified workshop.
The fuse allocation tables and
corresponding diagrams are available on
the website:
http://public.servicebox.peugeot.com/ddb/
You can go to a PEUGEOT dealer or a
qualified workshop.OK
Failed
Tw e e z e r s
Professional repairers: for full information
on the fuses and relays, consult the wiring
information and diagrams available at a
PEUGEOT dealer.
The replacement of a fuse not shown in
the allocation tables opposite may cause
a serious malfunction of your vehicle.
Contact a PEUGEOT dealer or a qualified
workshop.
8
In the event of a breakdown

174
Installing electrical
accessories
Your vehicle's electrical system is
designed to operate with standard or
optional equipment.
Before installing other electrical
equipment or accessories on your vehicle,
contact a PEUGEOT dealer or a qualified
workshop.
PEUGEOT accepts no responsibility for
the cost incurred in repairing your vehicle
or for rectifying malfunctions resulting
from the installation of accessories
not supplied and not recommended by
PEUGEOT and not installed in accordance
with specifications, in particular when the
combined power consumption of all of the
additional equipment connected exceeds
10

milliamperes.
On the left
Fuse no. Rating Functions
F1 (GPL) 10 AIgnition + (positive).
F2 5 AExterior mirrors, headlamps, diagnostic socket.
F9 5 AAlarm.
F10 5 AIndependent telematic unit, trailer interface unit.
F11 5 AElectrochrome interior rear-view mirror, additional
heating.
F13 5 AHi-Fi amplifier, parking sensors.
F16 15 AFront 12
V socket.
F17 15 AAudio system, after-market audio system.
F18 20 ATouch screen.
In the event of a breakdown

181
To w i n gReconnecting the (+) terminal
F Raise lever A fully.
F R efit open clamp B on the (+) terminal.
F

P
ush clamp B fully down.
F

L
ower lever A to lock clamp B .
Do not force the lever as locking will not
be possible if the clamp is not positioned
correctly; start the procedure again.
Following reconnection of the
battery
Following reconnection of the battery, switch on
the ignition and wait 1 minute before starting to
permit initialisation of the electronic systems. If
minor problems nevertheless persist following
this operation, contact a PEUGEOT dealer or a
qualified workshop.
Referring to the corresponding section, you
must yourself reinitialise (depending on
version):
-

t
he remote control key,
-
etc.The Stop & Start system may not be
operational during the trip following the
first engine start.
In this case, the system will only be
available again after a continuous
period of immobilisation of the vehicle,
a period which depends on the exterior
temperature and the state of charge of the
battery (up to about 8 hours). Procedure for having your vehicle towed or for
towing another vehicle using the towing eye.
8
In the event of a breakdown

184
Characteristics of engines
and towed loads
Engines
The engine characteristics are given in the
vehicle's registration document, as well as in
sales brochures.
Weights and towed loads
The maximum weights and towed loads for
your vehicle are given in the registration
document, as well as in sales brochures.
These values are also given on the
manufacturer's plate or label.
For more information, contact a PEUGEOT
dealer or a qualified workshop.The GTW values and the towable loads
listed are valid for a maximum altitude of
1,000
metres. The towable load must be
reduced by steps of 10% for each additional
1,000

metres.
The recommended nose weight is the vertical
load on the towbar ball (removable, with or
without tools).
GT W: Gross train weight.
High exterior temperatures may result
in a reduction in the per formance of the
vehicle to protect the engine. When the
exterior temperature is higher than 37°C,
limit the towed weight.
Towing using a lightly loaded vehicle can
adversely affect roadholding.
Braking distances are increased when
towing a trailer.
When using a vehicle to tow, never exceed
a speed of 60 mph (100 km/h) (obser ve
the local legislation in force). If the exterior temperature is high, it is
recommended that the engine be allowed
to idle for 1 to 2
minutes after the vehicle
comes to a stop, to facilitate its cooling.
The maximum power corresponds to the
value type-approved on a test bed, under
conditions defined in European legislation
(Directive 1999/99/EC).
For more information, contact a PEUGEOT
dealer or a qualified workshop.
Technical data

2
12:13
18,5 21,5
23 °CFirst steps
With the engine running, a press
mutes the sound.
With the ignition off, a press turns
the system on.
Adjustment of the volume.
Use the buttons either side of or below the
touch screen for access to the menus, then
press the virtual buttons in the touch screen.
Depending on the model, use the "Source" or
"Menu" buttons either side of the touch screen
for access to the menus, then press the virtual
buttons in the touch screen.
You can display the menu at any time by
pressing the screen briefly with three fingers.
All of the touch areas of the screen are white.
Press the cross to go back a level.
Press "OK" to confirm. The touch screen is of the "capacitive"
type.
To clean the screen, use a soft, non-
abrasive cloth (spectacles cloth) with no
additional product.
Do not use sharp objects on the screen.
Do not touch the screen with wet hands.
*
D

epending on equipment. Certain information is displayed permanently in
the upper band of the touch screen:
-

R
epeat of the air conditioning information
(depending on version), and direct access to
the corresponding menu.
-

G
o directly to the selection of the audio
source, to the list of radio stations (or list of
titles depending on the source).
-

G
o to the message notifications, emails,
map updates and, depending on the
services, the navigation notifications.
-

G
o to the settings for the touch screen and
the digital instrument panel. Selecting the audio source (depending on
version):
-

F
M / DAB radio stations* / AM*.
-

U
SB key.
-

C
D player (depending on model).
-

M
edia player connected via the auxiliary
socket (depending on model).
-

T
elephone connected via Bluetooth
and Bluetooth multimedia broadcast*
(streaming).
PEUGEOT Connect Nav

24
Make a long press on one of the
buttons to preset the station.
Activating / Deactivating
RDS
or Press Radio Media
to display the
primary page.
Press the " OPTIONS" button to go to the
secondary page.
Select "Radio settings ".
Select " General ".
Activate / Deactivate " Station
follow ". Press "
OK" to confirm.
RDS, if activated, allows you to continue
listening to the same station by automatic
retuning to alternative frequencies.
However, in certain conditions, coverage
of an RDS station may not be assured
throughout the entire country as radio
stations do not cover 100% of the territory.
This explains the loss of reception of the
station during a journey.Display text information
The "Radio Text" function allows
information transmitted by the radio
station and related to the station or the
song playing to be displayed.
or Press Radio Media
to display the
primary page. Press the "
OPTIONS" button to go to the
secondary page.
Select "Radio settings ".
Select " General ".
Presetting a station
Select a radio station or frequency.
(refer to the corresponding section)
Press "Presets ".
Activate / Deactivate "Display radio
text ".
Press " OK" to confirm.
PEUGEOT Connect Nav