2017 MITSUBISHI L200 change key battery

To extend
Unlocking the doors using the UNLOCKswitch (2), the outside rear-view mirrors are extended automatically.
NOTEl Functions can be modified as stated below.
Please consult a MITSUBISHI MOTORS
Authorized Service Point.
• Automatically extend when the driver’s
door is closed, and then the following op- eration is performed.
[Except vehicles equipped with keyless operation system]
Turn the ignition switch to the “ON” or
“ACC” position.
[Vehicles equipped with keyless operation
system]
Put the operation mode in ON or ACC.
• Automatically retract when the ignition
switch is turned to the “LOCK” position
or the operation mode is put in OFF, and the driver’s door is then opened.
• Automatically extend when the vehicle
speed reaches 30 km/h. NOTE• Deactivate the automatic extension func-
tion.

The outside rear-view mirrors can be fol-
ded or extended by the following opera-
tions, even if changing to any of the above.
After pressing the “LOCK” switch to lock
the doors, if the “LOCK” switch is press- ed again twice in a row within about 30
seconds, the outside rear-view mirrors will retract.
After pressing the “UNLOCK” switch to
unlock the doors, if the “UNLOCK”
switch is pressed again twice in a row within about 30 seconds, the outside rear-
view mirrors will extend again.
l The keyless entry system does not operate in
the following conditions:
• The key is left in the ignition switch. (ex-
cept for vehicles with keyless operation system)
• The operation mode is not in OFF. (vehi-
cles with keyless operation system)
• The door is open.
l The key switch will operate within approxi-
mately 4 m from the vehicle. However, the operating range of the key switch may
change if the vehicle is located near a TV
transmitting tower, power station, or radio
broadcasting station.
l If either of the following problems occurs,
the battery may be exhausted.NOTE• The key switch is operated at the correct
distance from the vehicle, but the doors are not locked/unlocked in response.
• The indication lamp (3) is dim or does not
come on.

For further information, please contact a
MITSUBISHI MOTORS Authorized
Service Point.
If you replace the battery yourself, refer to
“Procedure for replacing the key battery” on page 3-05.
l If your key is lost or damaged, please con-
tact a MITSUBISHI MOTORS Authorized
Service Point for a replacement key.
l If you wish to add key, please contact a
MITSUBISHI MOTORS Authorized Serv-
ice Point.
The following numbers of the keys are avail- able.
• Keyless entry key: up to 4 keys.
• Keyless operation key: up to 4 keys.Procedure for replacing the
key battery
E00309501546
Before replacing the battery, remove static
electricity from your body by touching a met- al grounded object.
Keyless entry system*
3-05OKTE17E1Locking and unlocking3

5. Close the key case firmly.
6. Attach the screw (A) removed in step 1.
(Keyless entry key only)
7. Check the keyless entry system to see
that it works.
Keyless operation system*
E00305601871
The keyless operation system allows you to lock and unlock the doors, start the engine
and change the operation mode simply by
carrying the keyless operation key with you. The switches on the keyless operation key can also be used as the key switch of keyless
entry system.
Refer to “Starting and stopping the engine” on page 6-17.
Refer to “Keyless entry system*” on page 3-03.

The driver should always carry the keyless operation key. This key is necessary for lock- ing and unlocking the doors, starting the en-
gine and otherwise operating the vehicle, so before locking and leaving the vehicle, be
sure to check that you have the keyless oper- ation key.WARNINGl People with implantable cardiac pace-
makers or implantable cardiovascular-de- fibrillators should not go near the exterior
transmitters (A) or the interior transmit-
ters (B). The radio waves used by the key-
less operation system could adversely af- fect implantable cardiac pacemakers orimplantable cardiovascular-defibrillators.
Keyless operation system*
3-07OKTE17E1Locking and unlocking3Keyless entry key+ side - side
Coin type battery CR1620 Keyless operation key+ side - side
Coin type battery CR2032 Club cab

WARNINGlWhen using electro-medical devices other
than implantable cardiac pacemakers or implantable cardiovascular-defibrillators,
contact the electro-medical device manu- facturer ahead of time to determine theaffects of radio waves on the devices. Elec-
tro-medical device operations could be af- fected by radio waves.
You can limit the possible operations of the
keyless operation system. Please consult a MITSUBISHI MOTORS Authorized Service
Point.
NOTEl The keyless operation key uses an ultra-
weak electromagnetic wave. In the following
cases, the keyless operation system may not
operate properly or may be unstable.
• When there is equipment nearby that
emits strong radio waves, such as: a pow-
er station, a radio/TV broadcasting station or an airport.
• The keyless operation system is carried
together with a communications device such as a cellular phone or radio set, or
with an electronic device such as a per- sonal computer.
• The keyless operation key is touching or
covered by a metal object.
• A keyless entry system is being used
nearby.
• When the keyless operation key battery is
worn out.
• When the keyless operation key is placed
in an area with strong radio waves or noise.
In such cases, use the emergency key.
Refer to “To lock/unlock without using
the keyless operation function” on page 3-11.NOTEl Because the keyless operation key receives
signals in order to communicate with the transmitters in the vehicle, the battery con-tinually wears down regardless of keylessoperation key use. The battery life is 1 to 2
years, depending on usage conditions. When the battery wears out, replace the battery ac-cording to the description in this manual or
have it replaced a MITSUBISHI MOTORS
Authorized Service Point.
Refer to “Procedure for replacing the key battery” on page 3-05.
l Because the keyless operation key continual-
ly receives signals, strong radio wave recep-
tion could affect battery wear. Do not leave the key near a TV, personal computer, or
other electronic device.Operating range of the keyless
operation system
E00305701609
If you are carrying the keyless operation key, enter the operating range of the keyless oper-
ation system, and press the driver’s or front
passenger’s door lock/unlock switch, the ID
code for your key is verified.
You can lock and unlock the doors, start the engine and change the operation mode only if
the ID codes of your keyless operation key
and the vehicle match.
Keyless operation system*
3-08OKTE17E1Locking and unlocking3Double cab

NOTElIf the keyless operation key battery is wear-
ing out or there are strong electromagnetic
waves or noise present, the operating range
may become smaller and operation may be-
come unstable.Operating range for locking
and unlocking the doors
E00306201568
The operating range is approximately 70 cm from the driver’s or front passenger’s door
lock/unlock switch.
*: Forward direction: Operating rangeNOTEl Locking and unlocking operates only when
you press a door switch that detects the key-
less operation key.
l Operation may not be possible if you are too
close to the front door, door window.
l Even if the keyless operation key is within
70 cm of the driver’s or front passenger’s
door lock/unlock switch, if the key is near to the ground or high up, the system may not operate.
l If the keyless operation key is within the op-
erating range, even someone not carrying the key can lock and unlock the doors by press-ing the driver’s or front passenger’s door
lock/unlock switch.Operating range for starting the
engine and changing the opera-tion mode
E00306301338
The operating range is the interior of the ve-
hicle.
*:Forward direction:Operating rangeNOTEl Even if it is within the operating range, if the
keyless operation key is in a small item
holder such as the glove box, on top of the instrument panel, door pocket or in the lug-gage compartment, it may be impossible to
start the engine and change the operation
mode.
Keyless operation system*
3-09OKTE17E1Locking and unlocking3

lWhen the engine switch or the operation
mode is in the following conditions, the
average fuel consumption display is au-
tomatically reset.
[Except for vehicles equipped with key-
less operation system]
The ignition switch is in the “ACC” or “LOCK” position for about 4 hours or
longer.
[For vehicles equipped with keyless op- eration system]
The operation mode is in ACC or OFF
for about 4 hours or longer.NOTEl The average fuel consumption display can
be reset separately for the auto reset mode and for the manual reset mode.
l The memory of the auto reset mode or man-
ual reset mode for the average fuel con- sumption display is erased if the battery isdisconnected.
l The initial (default) setting is “Auto reset
mode”.Changing the fuel consumption
display unit
E00523001808
The display unit for fuel consumption can be
switched. The distance and amount units are also switched to match the selected fuel con- sumption unit.
1. When you lightly press the multi infor-
mation display switch a few times, theinformation display switches to the aver-age fuel consumption display.
Refer to “Information display” on page
5-03.
2. Press and hold the multi information dis-
play switch for about 5 seconds or more until buzzer sound is heard twice.
3. Press and hold the multi information dis-
play switch to switch in sequence from “km/L” → “L/100 km” → “mpg” →“km/L”.NOTEl The display units for the driving range, the
average fuel consumption are switched, but the units for the indicating needle (speedom- eter), the odometer, the tripmeter and the
service reminder will remain unchanged.NOTEl The memory of the unit setting is erased if
the battery is disconnected, and it returns au- tomatically to factory setting.
The distance units is also switched in the fol-
lowing combinations to match the selected
fuel consumption unit.
Fuel consumptionDistance (driving range)km/LkmL/100 kmkmmpgmile(s)Changing the temperature unit
E00523101753
The display unit for outside temperature canbe switched. 1. When you lightly press the multi infor-
mation display switch a few times, the information display switches to the out-
side temperature display.
Refer to “Information display” on page
5-03.
2. Each time you press the multi informa-
tion display switch for 2 seconds or more on outside temperature display,you can switch from °C to °F or from °F
to °C unit of outside temperature dis-
play.
Multi-information display
5-10OKTE17E1Instruments and controls5

CAUTIONlDo not leave the key in the “ON” position
for a long time when the engine is not run-
ning, doing so will cause the battery to be discharged.
l Do not turn the key to the “START” position
while the engine is running. Doing so could damage the starter motor.Engine switch*
E00631801327
In order to prevent theft, the engine will notstart unless a preregistered keyless operation
key is used. (Engine immobilizer function)
If you are carrying the keyless operation key, you can start the engine.
CAUTIONl The indication lamp (A) will flash orange
when there is a problem or malfunction inthe keyless operation system. Never drive if
the indication lamp on the engine switch is
flashing orange. Immediately contact a
MITSUBISHI MOTORS Authorized Serv-
ice Point.
l If the engine switch operation is not smooth
and feels like it is sticking, do not operate the switch. Immediately contact a
MITSUBISHI MOTORS Authorized Serv-
ice Point.NOTEl When operating the engine switch, press the
switch all the way in. If the switch is not fully pressed, the engine may not start or theoperation mode may not change. If the en-
gine switch is pressed correctly, there is no need to hold the engine switch down.NOTEl When the battery in the keyless operation
key has worn out, or the keyless operationkey is out of the vehicle, a warning lampwill blink for 5 seconds.
Operation mode of the engine
switch and its function
OFF
The indication lamp on the engine switch
turns off.
The operation mode cannot be put in OFF when the selector lever is in any position oth-
er than the “P” (PARK) position (A/T).

ACC
Electrical devices such as the audio and ac-
cessory socket can be operated.
The indication lamp on the engine switch il-
luminates orange.

ON
Engine switch*
6-14OKTE17E1Starting and driving6

All vehicle’s electrical devices can be operat-ed.
The indication lamp on the engine switch il-
luminates green. The indication lamp turns
off when the engine is running.NOTEl Your vehicle is equipped with an electronic
immobilizer..
To start the engine, the ID code transmitted
by the transponder inside the key must match the code registered in the immobilizer
computer. Refer to “Electronic immobilizer
(Anti-theft starting system)” on page 3-03.Changing the operation mode
E00631901142
If you press the engine switch without de-
pressing the brake pedal (A/T) or the clutch
pedal (M/T), you can change the operation
mode in the order of OFF, ACC, ON, OFF.
CAUTIONl When the engine is not running, put the op-
eration mode in OFF. Leaving the operation mode in ON or ACC for a long time when
the engine is not running may cause the bat- tery to be discharged, making it impossible
to start the engine, lock and unlock the steer- ing wheel.
l When the battery is disconnected, the cur-
rent operation mode is memorized. After re- connecting the battery, the memorized modeis selected automatically. Before disconnect-
ing the battery for repair or replacement,
make sure to put the operation mode in OFF. Be careful if you are not sure which opera-
tion mode the vehicle is in when the battery
is run down.
l The operation mode cannot be changed from
OFF to ACC or ON if the keyless operation
key is not detected to be in the vehicle. Refer
to “Keyless operation system: Operating range for starting the engine and changing
the operation mode” on page 3-09.
l When there is the keyless operation key in
the vehicle and the operation mode isn’t
change, the keyless operation key may have worn out.ACC power auto-cutout func-
tion
E00632801151
After about 30 minutes has elapsed with the
operation mode in ACC, the function auto-
matically cuts out the power for the audio system and other electric devices that can be
operated with that position. (only that driv- er’s door has closed and the selector lever in
the “P” (PARK) position)
When you open driver’s door or the engine
switch operate again, the power is supplied
again.
NOTEl When ACC power supply automatic stop,
the steering wheel can’t lock and you can’t lock and unlock the doors by the keyless en-
try key and keyless operation key.
l It is possible to modify functions as follows:
• The time until the power cuts out can be
changed to approximately 60 minutes.
• The ACC power auto-cutout function can
be deactivated.
For details, we recommend you to consult
a MITSUBISHI MOTORS Authorized
Service Point.
Engine switch*
6-15OKTE17E1Starting and driving6

NOTElWhile the file is selected, hold down the key to cancel track search mode.
l Operations such as selecting a track will
cancel track search mode.Use AUX*
E00736901177
By connecting external input cables andAUX devices to this product, you can play
tracks on these devices through the product.

Press the MEDIA key to switch to the AUX
mode.
A- Auxiliary Audio connector (mini-jack)
CAUTIONl Connect an audio device with external sound
input mode cancelled, or with the soundturned down.
l Even if not inserted, the product will switch
to AUX, therefore take care with volume
levels when not inserted.NOTEl Depending on the audio device to be con-
nected, noise may be emitted.
l For power, use the battery power source in-
cluded in the audio device to be connected.
Using the connected audio device while charging through the cigarette lighter socket
in the vehicle may lead to noise being emit- ted through the speakers.
l If no audio devices are connected, then do
not select the external sound input mode. If external sound input mode is selected while
no audio devices are connected, then sound
may be emitted through the speakers.Display Indicator
E00738101085
This explains content of the display indicator.Change the Display Mode
E00738501106
You can change the content of the display in- dicator.
Press the 1DISP key to switch the display content.

Each time the 1DISP key is pressed, the dis-
play content changes.
CAUTIONl The operation of changing display contents
may impede safe driving, therefore check safety before operation.
Use AUX*
7-35OKTE17E1For pleasant driving7