2017 MITSUBISHI L200 display

Sports mode indicator
E00612301554
In sports mode, the currently selected posi-
tion is indicated by the indicator (A) shown
on the instrument panel.
When a malfunction occurs in
the automatic transmission
E00615101306
When the selector lever position
display blinks
E00615201336
When the selector lever position display blinks while you are driving, there could be a
malfunction in the automatic transmission system.
NOTEl “A” indicator does blink only the condition
that the A/T positional switch is broken.
It does not indicate in normal driving condi- tion.CAUTIONl If the selector lever position display blinks
while you are driving, it is likely that a safe-
ty device is operating because of a malfunc- tion in the automatic transmission. Immedi-
ately have the vehicle inspected at a MITSUBISHI MOTORS Authorized Serv-
ice Point.
Automatic transmission Sports Mode 5A/T
6-33OKTE17E1Starting and driving6 or through

NOTElIn sports mode, downshifts do not take place
when the accelerator is depressed all the way to the floor.Waiting
E00604601372
For short waiting periods, such as at traffic
signals, the vehicle can be left in gear and held stationary with the service brake.
For longer waiting periods with the engine
running, place the selector lever in the “N” (NEUTRAL) position and apply the parking
brake, while holding the vehicle stationary with the service brake.
CAUTIONl Never hold the vehicle stationary on a hill
using the accelerator pedal (without using
the brake pedal). Always apply the parking brake and/or service brakes.Parking
E00604700187
To park the vehicle, first bring it to a com-
plete stop, fully engage the parking brake,and then move the selector lever to the “P”
(PARK) position.
If you are going to leave the vehicle unatten-
ded, always switch off the engine and carry the key.
NOTEl On a slope, be sure to apply the parking
brake before moving the selector lever to the
“P” (PARK) position. If you move the selec- tor lever to the “P” (PARK) position before applying the parking brake, it may be diffi-
cult to disengage the selector lever from the
“P” (PARK) position when next you drive the vehicle, requiring application of a strong
force to the selector lever to move from the
“P” (PARK) position.When the automatic transmis-
sion makes no speed change
E00604801882
If the transmission does not change speeds
while driving, or your vehicle does not pick up enough speed when starting on an uphillslope, it may be that there is something un-
usual happening in the transmission, causing a safety device to activate. Immediately have
your vehicle checked at a MITSUBISHI
MOTORS Authorized Service Point. 1. If your vehicle has difficulty moving up-
hill, shift the selector lever into 2 nd
gear
of the sports mode. This method might
not work depending on the transmission malfunction.
2. Once the vehicle is moving on a level
road, move the selector lever back to“D” (DRIVE).
NOTEl When the selector lever position display in
the instrument panel blinks, it means that
there is an abnormal condition in the trans- mission.
Refer to “When the selector lever position
display blinks” on page 6-33.Easy select 4WD*
E00614701204
Shifting to rear-wheel drive or 4-wheel drivecan be made by operating the drive mode-se-
lector (A). Set the drive mode-selector to an appropriate position according to the roadsurface conditions. In addition, the 2WD/4WD operation indication lamp and the
low-range indication lamp indicates the drive
mode-selector setting state. Refer to “2WD/4WD operation indication lamp and low-range indication lamp” on page 6-38.
Easy select 4WD*
6-35OKTE17E1Starting and driving6

CAUTIONlIf the warning is turn on, the hill start assist
will not operate. Start off carefully.
l Park your vehicle in a safe place and stop
the engine.
Restart the engine and check whether the warning indicator went out, in which case
the hill start assist is again working normal- ly. If the warning remains displayed or reap-
pears frequently, it is not necessary to stop
the vehicle immediately, but the vehicle
should be inspected by a MITSUBISHI
MOTORS Authorized Service Point.Brake assist system
E00627001780
The brake assist system is a device assistingdrivers who cannot depress the brake pedalfirmly when it is necessary to do so (such as
in emergency stop situations) and provides
greater braking force.

If the brake pedal is depressed suddenly, the brakes will be applied with more force thanusual.
CAUTIONl The brake assist system is not a device de-
signed to exercise braking force greater than its capacity. Make sure to always keep a suf-
ficient distance between your vehicle and a
vehicle in front of you without relying too much on the brake assist system.NOTEl Once the brake assist system is operational,
it maintains great braking force even if the
brake pedal is lightly released.
To stop its operation, completely remove
your foot from the brake pedal.
l When the brake assist system is in use while
driving, you may feel the brake pedal at-
tempt to resist, the pedal moves in small mo- tions in conjunction with the operation
noise, or the vehicle body and the steering wheel vibrate. This occurs when the brake
assist system is operating normally and does not indicate faulty operation. Continue to
firmly depress the brake pedal.
l When the active stability & traction control
(ASTC) indication lamp is illuminated, the
brake assist system may not function.Emergency stop signal
system* E00626001129
This is a device that reduces the possibility of rear end collisions by the rapid and automatic blinking of the hazard warning lamps to alert
vehicles approaching from behind during sudden braking. When the emergency stop
signal system operates, the hazard warning indication lamp in the instrument cluster
blinks rapidly at the same time.CAUTIONl If the ABS warning lamp or ASTC indica-
tion lamp illuminates, the emergency stopsignal system may not operate. Refer to“ABS warning lamp” on page 6-57.
Refer to “ASTC indication lamp” on page
6-62.NOTEl [Activating condition for the emergency stop
signal system]
It activates when all of the following condi-
tions are met.
• The vehicle speed is approximately
55 km/h (34 mph) or higher.
Brake assist system
6-56OKTE17E1Starting and driving6

Speed Limiter information onthe multi information display area
E00633401095
The Speed Limiter information is displayed
on the multi information display area in the
combination meter.
A-Control state
There are 2 control states as below.
LIMIT OFF
When the Speed Limiter is in STAND-
BY, the vehicle speed can exceed the set speed
LIMIT
When the Speed Limiter is in operation.
The vehicle is controlled in order not to exceed the set speed.
B-SPEED LIMITER ON indication
When the Speed Limiter is started up, the Speed Limiter’s symbol is appeared.
C-Set speed
Set speed is appeared if it is stored.To start up
E00633501067
First of all, press the ON/OFF switch in order to power up the Speed Limiter when the igni-
tion switch in the “ON”, position or the oper- ation mode in ON,
The Speed Limiter indication will be ap-
peared in the combination meter.
To activate
E00633601084
Accelerate or decelerate to your desired
speed, and push down the SET - switch (B).
the Speed Limiter memorizes the current ve- hicle speed when you release the SET -
switch (B). Now, the Speed Limiter starts controlling in order not to exceed the set speed.
Speed Limiter
6-71OKTE17E1Starting and driving6 Type 1 Type 2

If the current vehicle speed is lower than ap-proximately 30 km/h (19 mph) (settable min- imum speed), the set speed is set at approxi-
mately 30 km/h (19 mph).
The set speed is displayed in the combination meter.
And, control state “LIMIT” is displayed in
the combination meter.To increase the set speed
E00633700017
By using the RES + switch
E00633801073
Push up the RES + switch continuously.
Then the set speed displayed in the combina- tion meter is gradually increased.
If the set speed reaches your desired speed,
release the RES + switch (C).
The set speed is increased each approximate- ly 5 km/h (3 mph).
If a driver wants to increase the set speed a
little, push up RES + switch and release it. The set speed is increased 1 km/h each taps.
By using the CANCEL switch,
the accelerator pedal and the
SET - switch
E00633901090
Press the CANCEL switch (D) to deactivate
the Speed Limiter.
Control state “LIMIT” is disappeared and change control state “LIMIT OFF” in the
combination meter.
Speed Limiter
6-72OKTE17E1Starting and driving6 Type 1 Type 2 Type 1 Type 2

Accelerate to driver’s desired vehicle speedand push down SET - switch (B) and release.Control state “LIMIT” is displayed again andthe set speed is updated.
To decrease the set speed
E00634000017

By using the SET - switch
E00634101073
Push down the SET - switch (B).

Then the set speed displayed in the combina- tion meter is gradually decreased.
If the set speed reaches to your desired speed,
release the SET - switch (B).
The set speed decreases each approximately5 km/h (3 mph).
If a driver wants to decrease the set speed a
little, press SET - switch (B) and release it.
The set speed is decreased 1 km/h each taps.
Speed Limiter
6-73OKTE17E1Starting and driving6 Type 1 Type 2 Type 1 Type 2

By using the CANCEL switch,the service brake and the SET - switch
E00634201087
Press the CANCEL switch (D) to deactivate
the Speed Limiter.
Control state “LIMIT” is disappeared and
change control state “LIMIT OFF” in the combination meter.
Decelerate to driver’s desired speed and push
down SET - switch (B) and release.The Speed Limiter indication is displayed
again and the set speed is updated.
To increase the vehicle speed
temporarily
E00634301091
A driver can temporarily accelerate for emer-
gency use.

The Speed Limiter is temporarily deactiva- ted, and the vehicle speed can be increased.
Speed Limiter
6-74OKTE17E1Starting and driving6Type 1 Type 2 Type 1 Type 2

However, the Speed Limiter immediately
starts controlling and the vehicle decreases as if an accelerator pedal is closed fully, whenthe vehicle speed is higher than the set speed.
CAUTIONl There is a possibility to occur jerk, depend-
ing on a running resistance. Be careful.Lane Departure Warning
(LDW)* E00635701050
By recognizing through a camera (A) the lane
in which your vehicle is running, LDW gives you warning when your vehicle is likely to drift from its lane with an audible alarm and a
visual alarm displayed on the information
screen of the multi information display.How to operate LDW
E00635801077
The indication changes as follows depending
on the state of the system.
Turning on the system
When you set the ignition switch or operation
mode to “ON”, the LDW system ON indica- tion lamp appears, showing that the system is
placed in the ‘ON state’.
Lane Departure Warning (LDW)*
6-76OKTE17E1Starting and driving6Type 2