2017 MITSUBISHI iMiEV light

Combination headlights and dimmer switch 5-46 Features and controls
5
N00573700020
If the warning light illuminates when the out- side air temperature is very low, move thevehicle to a warmer location.
If the warning light illuminates after the vehi- cle has been driven continuously uphill orwhen the outside air temperature is very high, stop the vehicle in a safe place so the electric motor unit and/or the main drive lithium-ionbattery can cool down. When they have cooled down, the warning light will go off. If the warning light does not turn off, contact acertified i-MiEV dealer.
N00522501805
Rotate the switch to operate the lights.
Power down warning light
If this warning light illumi-nates, the power provided by the electric motor will be reduced and the vehicle willbe only able to move at low speeds. This warning light will illu-minate;  When the energy level in the main drive lithium-ion battery is near empty.  When temperature of the electric motor unit or the main drive lithium-ion battery is too high or toolow.  When voltage of the main drive lithium-ion batterybecomes low.
If the energy level gauge shows 0 bar, the main drivelithium-ion battery is near empty and must be charged as soon as possible. Refer to“Charging” on page 3-13.
NOTE
 When the power down warning light illumi- nates, avoid rapid st
arts and aggressive
acceleration.  Illumination of the
power down warning
light does not indica
te a malfunction.
 If the power down warn
ing light illuminates
while the air conditioning is used, the cool- ing or heating may stop operating and only the fan will operate.
Combination headlights and dimmer switch Headlights
NOTE
 Do not leave the headli
ghts and other lights
on for a long period of time while the readyindicator is not illu
minated. A run down 12V
starter battery
could result.
 When it rains, or wh
en the vehicle has been
washed, the inside of the lens sometimes becomes foggy. This is the same as whenwindow glass mists up on a humid day, and does not indicate a pr
oblem. When the light
is switched on, the heat will dry out the fog.However, if water collects inside the light, have it checked by a certified i-MiEV dealer.
BK0220401US.book 46 ページ ２０１５年６月３日　水曜日　午前７時４２分

Combination headlights and dimmer switch
Features and controls 5-47
5
The combinations of switch operations and illuminated lights differ in accordance withthe following conditions. [When the ready indicato
r is illuminated, and
the parking brake is released] The daytime running light
s will be illumi-
nated:
[When the ready indicator is not illuminated, or when the ready indicator is illuminated but the parking brake is not released] The electric motor unit starts when the lights are off.
N00532600554
 If the key is turned to “LOCK” or “ACC”
from the electric
motor switch and the driver’s door is opened with the combination headlights and dimmer switch in the “ ” or “ ”
OFF
The daytime running lights illumi- nated
AUTO
The daytime running lights illumi- nated Headlights and other lights turn on and off automatically in accor-dance with outsi
de light level.
The daytime running lights illumi- nated Parking, tail, front and rear side- marker lights, license plate and instrument panel lights on Headlights and other lights on
NOTE
 Once the daytime running light come on, they do not go out until the electric motorswitch is turned to the “LOCK” or “ACC”OFF All lights off AUTO
Headlights and other lights turn on and off automatically in accor-dance with outside light level. Parking, tail, front and rear side- marker lights, license plate and instrument panel lights on Headlights and other lights on
NOTE
 The sensitivity of the automatic on/off con- trol can be adjusted.For further information,
please contact a cer-
tified i-MiEV dealer.  Do not place anything on
the sensor (A), and
do not clean with a glas
s cleaner. Clean only
with clear water.  If the lights do not turn on or off with the switch in the “AUTO” operate the switch. Have
the system checked
by a certified i-MiEV dealer.
Light auto-cutout function (headlights and other lights)
BK0220401US.book 47 ページ ２０１５年６月３日　水曜日　午前７時４２分

Combination headlights and dimmer switch 5-48 Features and controls
5
• If the driver’s door is opened after the key is removed from the electric motorswitch, a buzzer will sound to remind you to turn off the lights. • If the driver’s door is opened with thekey in the electric motor switch, a buzzer will sound intermittently to remind you to remove the key.
 If the key is turned to “LOCK” or “ACC” position with the driver’s door closed and the combination headlights and dimmer switch in the “ ” or “ ” position, the lights will stay on for about 3 minutes and then turn off automatically.
If the combination headlights and dimmer switch is turned to the “ ” or “ ” posi- tion again after the electric motor switch is turned to “LOCK” or “ACC” position, the auto-cutout function de
scribed above will not
work. The lights (the pa
rking lights, tail lights
and license plate lights)
will stay on and will
not turn off automatically.
N00549800213
If the driver’s door is opened with the key removed from the electric motor switch while the lights are on, the buzzer will sound toremind you to turn off the lights. The lights and buzzer will turn off automati- cally.Or you can turn the combination headlights and dimmer switch to the “OFF” position to stop the buzzer.
N00549900155
To change the headlights from high beam tolow beam and vice vers
a, pull the turn signal
lever to fully toward you (1). Switch the
headlights to low beam as a courtesy when- ever there are oncoming vehicles, or whenthere is traffic moving ahead of you. An illu- minated blue light in
the instrument cluster
indicates when the headlights are on highbeam.
N00550000198
You can flash the high beams by pulling thelever gently toward you (2). The lights willgo back to normal when you let go. While the high beam is on, you will
see a blue light on
the instrument panel.
NOTE
 The light auto-cutout
function can be deacti-
vated. See a certified i-MiEV dealer for details.
When you want to keep the lights on:
NOTE
 If the driver’s door is opened and the key is removed, the headlight
reminder buzzer will
sound. If the key is still in the electric motor switch the key reminder buzzer will soundintermittently. The buzzer stops when the driver’s door is closed.
Headlight reminder buzzer Dimmer (high/low beam change)
Headlight flasher
NOTE
 You can flash the high beams by pulling the lever toward you, even if the combination headlights and dimmer switch is off.
BK0220401US.book 48 ページ ２０１５年６月３日　水曜日　午前７時４２分

Turn signal lever
Features and controls 5-49
5
N00522600506
When changing lanes, or to making a gradual turn, hold the lever in the “lane change” posi- tion (1). It will return to the neutral positionwhen you let go. Use the full position (2) when making a normal turn. The lever will return to the neutral position when the turn iscomplete. There may be times when the lever does not return to th
e neutral position. This
usually happens when
the steering wheel is
turned only slightly. You
can easily return the
lever by hand. Also, when you move the lever to (1) slightlythen release it, the turn signal lights and indi- cator in the instrument cluster will flash three times.
N00522700305
If you press the flasher switch, the front andrear turn signals will flash intermittently, and so will the hazard warning lights. This is an emergency warning system and should not beused when the vehicle is in motion, except for emergencies. If you need to leave your
vehicle, the flashers
will keep working after the key is removed from the electric motor switch.
 If you turn the lights off with the headlights set to high-beam illumi
nation, the headlights
are automatically returned to their low-beamsetting when the combination headlights and dimmer switch is next turned to the “ ”
Turn signal lever
NOTE
NOTE
 A light in the instrument panel flashes to show when the front and rear turn signallights are working properly. If this light flashes fast
er than usual, check
for a burned out light
bulb or malfunctioning
connection. If the panel light does not come on when the lever is moved, check
for a blown fuse or a
burned out bulb in the panel. Have the vehicle insp
ected by a certified i-
MiEV dealer.  It is possible to modify functions as follows: • Deactivate the turn signal light 3-flash function for lane changes. • Adjust the time required to operate the lever for the 3-flash function. See a certified i-MiEV dealer for details.
Hazard warning flasher switch
NOTE
 If you keep the flashers on for a long period of time while the ready
indicator is not illu-
minated, the 12V starte
r battery could go flat
and the electric motor unit could be impossi- ble to start.
BK0220401US.book 49 ページ ２０１５年６月３日　水曜日　午前７時４２分

Front fog light switch 5-50 Features and controls
5
N00522801433
The front fog lights illuminate only when the headlights are on low beam. Turning the knob in the direction of the “ON”position turns on the front fog lights as well as the indicator in the instrument cluster. To turn them off, turn the knob in the direction ofthe “OFF” position. The knob will return to the neutral position when it is released.
N00523000640
The windshield wiper and washer can be operated with the electric motor switch in the “ON” or “ACC” position.If the blades are frozen to the windshield, do not operate the wipers until the ice has melted
and the blades are freed, otherwise the wiper motor may be damaged. With the lever in the “INT” (speed sensitive intermittent operation) position, the intermit- tent intervals can be adjusted by turning theknob (A).
Front fog light switch
NOTE
 If the headlights are switched to high beam, the front fog lights will
go out; they will illu-
minate again when the headlights areswitched back to low beam.
 If the combination headlights and dimmer switch is rotated to the “OFF” or “ ” posi- tion while the front fog lights are illumi-nated, they will automatically turn off. They can be turned back on again by rotating the combination headlight
s and dimmer switch
back to “ ” position, and turning the knob in the direction of the “ON” position.  Do not use fog lights ex
cept in conditions of
fog, otherwise excessive light glare may temporarily blind oncoming vehicle drivers.
Wiper and washer switch
CAUTION If the washer is used
in cold weather, the
washer fluid sprayed against the glass mayfreeze, which may hinder visibility. Warm the glass with the defroster before using the washer.
Windshield wipers
NOTE
MIST- Misting function
The wipers will operate once.
OFF- OffINT- Intermittent (Speed sensitive) HI- Fast
To adjust intermittent intervals
BK0220401US.book 50 ページ ２０１５年６月３日　水曜日　午前７時４２分

Electric rear window defogger switch 5-52 Features and controls
5
N00523500241
N00523701455
The electric rear window defogger can be used when the ready i
ndicator is illuminated.
The indicator light (A) will come on whenyou press the electric rear window defogger switch. Electric current will flow through the heating wires on the rear window to helpclear away moisture or frost. After about 20 minutes of operation, the sys- tem will shut off automatically. To switch the defogger OFF before 20 min-utes have passed, press the switch again. The indicator light will go
out and the defogger
will turn off. If you need the defogger for more than 20 minutes, press th
e switch again. This will add
20 more minutes.
NOTE
 To ensure a clear rearward view, the wiper performs several continuous operationswhen the reverse gear is engaged and theswitch is in the “INT” position. Following this continuous operation, the wiper will automatically switch to intermit-tent operation.  It is possible to modify functions as follows: • Adjustment of the interval for intermittent operation • Changing intermittent
wiper operation to
continuous wi
per operation
For details, consult a certified i-MiEV dealer.
 The washer fluid rese
rvoir is located under-
neath the hood. Check the fluid level regularly and refill ifnecessary. (Refer to
“Washer fluid” on page
9-7.)
using wipers and washers
CAUTION If the washer is used in cold weather, the washer fluid spraye
d onto the glass might
freeze, blocking your view. In cold weather, heat the glass with the
defroster before using
the washer.
NOTE
 Do not use the wipers when the windshield is dry. This could scratch the glass and wear thewiper blades prematurely.  Before using the wipe
rs in cold weather,
check to be sure that the wiper blades are notfrozen to the windshield. Using the wipers while the blades are frozen could cause the wiper motor to burn out.  If the wipers are left on the glass out of the parked position and they become blocked byice or other deposits on the glass, the motor may still burn out even
if the wiper switch is
OFF. If deposits form on the windshield,park your vehicle in a safe place, turn off the electric motor switch, and clean the glass so that the wipers ca
n operate smoothly.
 Avoid using the washer for more than 20 sec- onds at a time. Do not operate the washerwhen the fluid reservoir is empty or the pump may fail.  During cold weather, add a recommended washer solution that will not freeze in the washer reservoir. Otherwise the washer maynot work or may be damaged.  Replace the wiper blades when they are worn. Use the proper size replacement blades. If you have questions, ask a certified i-MiEV dealer.
Electric rear window defog- ger switch
BK0220401US.book 52 ページ ２０１５年６月３日　水曜日　午前７時４２分

Horn switch
Features and controls 5-53
5
N00523800172
To honk the horn, press around the “ ” mark on the steering wheel.
N00563700030
The Link System takes ove
rall control of the
devices connected via the USB input terminal or the Bluetooth
® 2.0 interface allowing the
connected devices to be operated by using theswitches in the vehicl
e or voice commands.
See the following sect
ion for details on how
to operate. Refer to “Bluetooth
® 2.0 interface” on page
5-53. Refer to “USB input terminal” on page 5-73.
Refer to “To play iPod/USB memory device tracks via voice operation” on page 7-20. Bluetooth
® is a registered trademark of
BLUETOOTH SIG, INC.
N00563800015
You have acquired a devi
ce that includes soft-
ware licensed by Mitsub
ishi Motors Corpora-
tion from JOHNSON CONTROLS Inc (the automotive experience business unit), and their subsequent 3rd
party suppliers. For a
complete list of these
3rd party products and
their end user license
agreements, please go
to the following website.http://www.jciblueconne
ct.com/faq/fulldis-
closure.pdf
N00563901286
The Bluetooth
® 2.0 interface allows for mak-
ing/receiving ha
nds-free calls in the vehicle
using a Bluetooth
® compatible cellular phone
based on the wireless communication tech- nology commonly known as Bluetooth
®. It
also allows the user to play music, saved in a
CAUTION The rear window defogge
r is not designed to
melt snow. Remove
any snow manually
before using the rear window defogger. Use the rear window de
fogger only after the
ready indicator is illuminated. Be sure to turnthe defogger switch off immediately after the window is clear to sa
ve on 12V starter bat-
tery power. Do not place stickers,
tape, or other items
that are attached with adhesive over the gridwires on the rear window. When cleaning the inside
rear window, use a
soft cloth and wipe lightly over the grid wires.NOTE
 If your vehicle is equi
pped with heated mir-
rors, mist can also be removed from the out-side rearview mirrors when the rear window defogger switch is pressed. (Refer to “Heated mirror”
on page 5-18.)
vated automatically when the Remote Cli-mate Control is activated in Pre-DefrosterMode. Refer to “Remote Climate Control” on page 3-36, 3-47 and “For persons with electro-medical apparatus such
as implantable car-
diac pacemaker or im
plantable cardiovascu-
lar defibrillator” on page 3-6.
Horn switch Link System
(if so equipped)
Agreement

Bluetooth
® 2.0 interface
(if so
equipped)
BK0220401US.book 53 ページ ２０１５年６月３日　水曜日　午前７時４２分

Interior lights
Features and controls 5-77
5
N00525300559 N00525800222
The dome light can be turned on by sliding the dome light switch.Interior lights 1- Dome light (Rear)
 P.5-78
2- Dome light (Fr
ont)/Reading lights
 P.5-77
Dome light (Front)/Reading lights
(if so equipped)
Dome light (Front)

1- Door 2- Off 1- (DOOR)
 The dome light comes on when any door or the liftgate
is opened. It goes
off approximately 30 seconds afterthe door or liftgate is closed (delayed off function). However, the light goes off immediately if:• The door and the liftgate are closed and the electric motor switch is turned to the “ON” position.• The driver’s door is closed after all the other doors are closed while the lock knob of the driver’s door is in the lock position. • The door and the liftgate are closedand the power door lock switch is used to lock the doors. • The keyless entry system remotecontrol transmitter is used to lock the doors.
BK0220401US.book 77 ページ ２０１５年６月３日　水曜日　午前７時４２分