2017 MAZDA MODEL CX-5 brakes

3–49
Before Driving
Driving Tips
Break-In Period
No special break-in is necessary, but a
few precautions in the fi rst 1,000 km
(600 miles) may add to the performance,
economy, and life of the vehicle.
   Do not race the engine.  Do not maintain one constant speed,
either slow or fast, for a long period of
time.
   Do not drive constantly at full-throttle or
high engine rpm for extended periods of
time.
   Avoid unnecessary hard stops.  Avoid full-throttle starts.  Do not tow a trailer.
Saving Fuel and Protection
of the Environment
How you operate your Mazda determines
how far it will travel on a tank of fuel. Use
these suggestions to help save fuel and
reduce CO
2 .   Avoid long warm-ups. Once the engine
runs smoothly, begin driving.
   Avoid fast starts.  Drive at lower speeds.  Anticipate when to apply the brakes
(avoid sudden braking).
   Follow the maintenance schedule
(page 6-4 ) and have an Authorized
Mazda Dealer perform inspections and
servicing.
   Use the air conditioner only when
necessary.
   Slow down on rough roads.  Keep the tires properly in fl ated.   Do not carry unnecessary weight.  Do not rest your foot on the brake pedal
while driving.
   Keep the wheels in correct alignment.  Keep windows closed at high speeds.  Slow down when driving in crosswinds
and headwinds.

WARNING
Never stop the engine when going down
a hill: Stopping the engine when going
down a hill is dangerous. This causes
the loss of power steering and power
brake control, and may cause damage
to the drivetrain. Any loss of steering
or braking control could cause an
accident.

CX-5_8FN1-EA-16L_Edition1.indb 492016/12/12 10:05:37

3–50
Before Driving
Driving Tips
Hazardous Driving
WARNING
Be extremely careful if it is necessary to
downshift on slippery surfaces: Downshifting into lower gear
while driving on slippery surfaces is
dangerous. The sudden change in tire
speed could cause the tires to skid. This
could lead to loss of vehicle control
and an accident.

Avoid sharp turns, excessive speed and
abrupt maneuvers when driving this
vehicle: Sharp turns, excessive speed and
abrupt maneuvering of this vehicle
are dangerous as it could result in the
increased risk of loss of vehicle control,
vehicle roll-over, personal injury or
death.
This vehicle has a higher center of
gravity. Vehicles with a higher center of
gravity such as utility vehicles handle
diff erently than vehicles with a lower
center of gravity.
Utility vehicles are not designed for
cornering at high speeds any more
than low profi le sports cars are
designed to perform satisfactorily
under off -road conditions.
In addition, utility vehicles have a
signifi cantly higher rollover rate than
other types of vehicles.
In a rollover crash, an unbelted person
is signifi cantly more likely to die than a
person wearing a seat belt.

When driving on ice or in water, snow,
mud, sand, or similar hazards:
  Be cautious and allow extra distance for
braking.
   Avoid sudden braking and sudden
maneuvering.
   Do not pump the brakes. Continue to
press down on the brake pedal.
 Refer to Antilock Brake System (ABS) on page 4-82 .
  If you get stuck, select a lower gear and
accelerate slowly. Do not spin the front
wheels.
   For more traction in starting on slippery
surfaces such as ice or packed snow,
use sand, rock salt, chains, carpeting, or
other nonslip material under the front
wheels.

NOTE
Use snow chains only on the front wheels.
CX-5_8FN1-EA-16L_Edition1.indb 502016/12/12 10:05:37

3–52
Before Driving
Driving Tips
Winter Driving
Carry emergency gear, including tire
chains, window scraper, fl ares, a small
shovel, jumper cables, and a small bag of
sand or salt.
Ask an Authorized Mazda Dealer to check
the following:
   Have the proper ratio of antifreeze in the
radiator.
 Refer to Engine Coolant on page 6-25 .
  Inspect the battery and its cables. Cold
reduces battery capacity.
   Use an engine oil appropriate for the
lowest ambient temperatures that the
vehicle will be driven in (page 6-23 ).
  Inspect the ignition system for damage
and loose connections.
   Use washer fl uid made with antifreeze—
but do not use engine coolant antifreeze
for washer fl uid (page 6-27 ).

NOTE
  Remove snow before driving. Snow left
on the windshield is dangerous as it
could obstruct vision.
  Do not apply excessive force to a
window scraper when removing ice or
frozen snow on the mirror glass and
windshield.
  Never use warm or hot water for
removing snow or ice from windows and
mirrors as it could result in the glass
cracking.
  Drive slowly. Braking performance
can be adversely affected if snow or
ice adheres to the brake components. If
this situation occurs, drive the vehicle
slowly, releasing the accelerator pedal
and lightly applying the brakes several
times until the brake performance
returns to normal.

Snow Tires
Use snow tires on all four wheels
Do not go faster than 120 km/h (75 mph)
while driving with snow tires. In fl ate snow
tires 30 kPa (0.3 kgf/cm
2 , 4.3 psi) more
than recommended on the tire pressure
label (driver's door frame), but never
more than the maximum cold-tire pressure
shown on the tires.

Except Mexico
The vehicle is originally equipped with
all season radials designed to be used all
year around. In some extreme climates you
may fi nd it necessary to replace them with
snow tires during the winter months to
further improve traction on snow and ice
covered roads.
Mexico
The vehicle is originally equipped with
summer tires designed for optimum
traction on wet and dry roads. If your
vehicle is to be used on snow and ice
covered roads, Mazda recommends that
you replace the tires originally equipped
on your vehicle with snow tires during the
winter months.
WARNING
Use only the same size and type tires
(snow, radial, or non-radial) on all four
wheels: Using tires diff erent in size or type is
dangerous. Your vehicle's handling
could be greatly aff ected and result in
an accident.

CAUTION
Check local regulations before using
studded tires.

CX-5_8FN1-EA-16L_Edition1.indb 522016/12/12 10:05:38

3–53
Before Driving
Driving Tips
Tire Chains
Check local regulations before using tire
chains.
CAUTION
 Chains may aff ect handling. Do not go faster than 50 km/h
(30 mph) or the chain manufacturer's
recommended limit, whichever is lower.
 Drive carefully and avoid bumps, holes, and sharp turns.
 Avoid locked-wheel braking. Do not use chains on a temporary spare tire; it may result in damage to the
vehicle and to the tire.
 Do not use chains on roads that are free of snow or ice. The tires and chains could
be damaged.
 Chains may scratch or chip aluminum wheels.

NOTE
If your vehicle is equipped with the tire
pressure monitoring system, the system
may not function correctly when using tire
chains.

Install the chains on the front tires only.
Do not use chains on the rear tires.
Please consult an Authorized Mazda
Dealer.
Installing the chains
1. Secure the chains on the front tires as tightly as possible.
Always follow the chain manufacturer's instructions.
2. Retighten the chains after driving 1/2—1 km (1/4—1/2 mile).

Driving In Flooded Area
WARNING
Dry off brakes that have become
wet by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the brake
performance returns to normal: Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been aff ected.

CAUTION
Do not drive the vehicle on fl ooded
roads as it could cause short circuiting
of electrical/electronic parts, or
engine damage or stalling from
water absorption. If the vehicle has
been immersed in water, consult an
Authorized Mazda Dealer.

CX-5_8FN1-EA-16L_Edition1.indb 532016/12/12 10:05:38

3–60
Before Driving
Towing
Safety Chains
Safety chains must be used as a precautionary measure should the trailer\
become
unintentionally unhitched. They should cross under the trailer tongue and attach to the hitch.
Leave enough slack to allow full turns. Consult literature published by \
your trailer or hitch
manufacturer for more details.
WARNING
Make sure the safety chain is securely attached to both the trailer and the vehicle prior
to departure: Towing a trailer without using a safety chain securely attached to both the trailer and the
vehicle is dangerous. If damage occurs to the coupling unit or hitch ball, the trailer could
wander into another lane and cause a collision.

Trailer Lights
Trailer lights must comply with all federal, state, and local regulations\
. Equip your trailer as
required before towing it day or night.
CAUTION
Do not connect a trailer lighting system directly to the lighting system of your Mazda. This
may damage your vehicle's electrical system and lighting systems. Have a recreational
vehicle dealer or trailer rental agency connect the system, and inspect the brake lights
and turn signals yourself before each trip.

Trailer Brakes
If the total trailer weight exceeds 450 kg (1,000 lb), trailer brakes \
are required. If your trailer
has brakes, make sure they comply with all federal, state, and local reg\
ulations.
WARNING
Do not connect a hydraulic trailer-brake system to your vehicle's brake system: Connecting a hydraulic trailer-brake system directly to the vehicle brake system is
dangerous and will result in inadequate braking and possible injury.

CX-5_8FN1-EA-16L_Edition1.indb 602016/12/12 10:05:39

3–62
Before Driving
Towing
Passing
Plan well ahead to pass other vehicles, and provide plenty of room befor\
e changing lanes.
Crosswinds from passing vehicles, especially larger ones, and the effects of rough roads will
affect handling.
If swaying occurs, fi rmly grip the steering wheel and reduce speed immediately, but
gradually.
Steer straight ahead. If no extreme correction of steering or braking is\
made, the
combination of less speed and fi rm steering will result in stability.
Backing up
Backing a vehicle with a trailer requires practice and patience. Back sl\
owly, and have a
helper outside at the rear of the trailer to reduce the risk of an accid\
ent.
To turn the trailer, place your hand at the bottom of the steering wheel and turn it in the\

direction you want the trailer to go. Make only slight movements to prev\
ent sharp or
prolonged turning.
Ascending a hill
Shift into a lower gear to reduce the possibility of overloading or over\
heating the engine, or
both.
Descending a hill
Shift into a lower gear and use engine compression as a braking effect.
WARNING
Always use lower gears to reduce speed: Holding the brake pedal down too long or too frequently is dangerous as it could cause
the brakes to overheat and lose power, resulting in loss of control and a serious accident.
Use lower gears to help reduce speed. Pull off the road and allow brakes to cool down
whenever braking performance feels reduced.

Overheated engine
The extra weight of the trailer may strain the engine on hot days and on\
long or steep
upgrades.
If the temperature gauge indicates overheating, turn off the air conditioner, drive safely
to the side of the road, park off the right-of-way and wait for engine to cool. Refer to
Overheating on page 7-18 .
CX-5_8FN1-EA-16L_Edition1.indb 622016/12/12 10:05:39

4–43
When Driving
Automatic Transaxle
Shift-Lock System
The shift-lock system prevents shifting out
of P unless the brake pedal is depressed.

To shift from P:

1. Depress and hold the brake pedal.
2. Start the engine.
3. Press and hold the lock-release button.
4. Move the selector lever.

NOTE
  When the ignition is switched to ACC or
the ignition is switched off, the selector
lever cannot be shifted from P.
  The ignition cannot be switched to OFF
if the selector lever is not in P.

Shift-Lock Override
If the selector lever will not move from P
using the proper shift procedure, continue
to hold down the brake pedal.

1. Remove the shift-lock override cover using a cloth-wrapped fl at head
screwdriver.
2. Insert a screwdriver and push it down.

Cover

3. Press and hold the lock-release button.
4. Move the selector lever.

Take the vehicle to an Authorized Mazda
Dealer to have the system checked.
Transaxle Ranges
   The shift position indicator light in the
instrument cluster illuminates. Refer
to Warning/Indicator Lights on page
4-32 .
   The selector lever must be in P or N to
operate the starter.

P (Park)
P locks the transaxle and prevents the front
wheels from rotating.
WARNING
Always set the selector lever to P and set
the parking brake: Only setting the selector lever to the
P position without using the parking
brake to hold the vehicle is dangerous.
If P fails to hold, the vehicle could move
and cause an accident.

CAUTION
 Shifting into P, N or R while the vehicle is moving can damage your transaxle.
 Shifting into a driving gear or reverse when the engine is running faster than
idle can damage the transaxle.

R (Reverse)
In position R, the vehicle moves only
backward. You must be at a complete
stop before shifting to or from R, except
under rare circumstances as explained in
Rocking the Vehicle (page 3-51 ).
N (Neutral)
In N, the wheels and transaxle are not
locked. The vehicle will roll freely even
on the slightest incline unless the parking
brake or brakes are on.
CX-5_8FN1-EA-16L_Edition1.indb 432016/12/12 10:05:52

4–50
When Driving
Automatic Transaxle
Driving Tips
WARNING
Do not let the vehicle move in a
direction opposite to the direction
selected by the selector lever: Do not let the vehicle move backward
with the selector lever in a forward
position, or do not let the vehicle
move forward with the selector lever
in the reverse position. Otherwise, the
engine may stop, causing the loss of
the power brake and power steering
functions, and make it diffi cult to
control the vehicle which could result
in an accident.

Passing
For extra power when passing another
vehicle or climbing steep grades, depress
the accelerator fully. The transaxle will
shift to a lower gear, depending on vehicle
speed.
NOTE
   The accelerator pedal may initially feel
heavy as it is being depressed, then feel
lighter as it is depressed further. This
change in pedal force aids the engine
control system in determining how
much the accelerator pedal has been
depressed for performing kickdown,
and functions to control whether or not
kickdown should be performed.
  While the selector lever is in the M
position and the TCS is turned off,
manual shift mode does not switch
to automatic shift mode even if the
accelerator pedal is completely
depressed. Operate the selector lever.

Climbing steep grades from a stop
To climb a steep grade from a stopped
position:

1. Depress the brake pedal.
2. Shift to D or M1, depending on the load weight and grade steepness.
3. Release the brake pedal while gradually accelerating.

Descending steep grades
When descending a steep grade, shift to
lower gears, depending on load weight and
grade steepness. Descend slowly, using the
brakes only occasionally to prevent them
from overheating.
CX-5_8FN1-EA-16L_Edition1.indb 502016/12/12 10:05:53