2017 MAZDA MODEL CX-5 clutch

Ignition Switch
▼Push Button Start Positions
The system operates only when the key is
within operational range.
Each time the push button start is pressed,
the ignition switches
in the order of off,
ACC, and ON. Pressing the push button
start again from ON switches the ignition
off.
Indicator light
Push button start
NOTE
•The engine starts by pressing the push
button start while depressing the clutch
pedal (manual transaxle) or the brake
pedal (automatic transaxle). To switch
the ignition position, press the push
button start without depressing the
pedal.
•Do not leave the ignition switched ON
while the engine is not running. Doing
so could result in the battery going
dead. If the ignition is left in ACC (For
automatic transaxle, the selector lever is
in the P position, and the ignition is in
ACC), the ignition switches off
automatically after about 25 minutes.
Off
The power supply to electrical devices
turns off and the push button start
indicator light (amber) also turns off.
In this position the steering wheel is
locked.
WA R N I N G
Before leaving the driver's seat, always
switch the ignition off, set the parking
brake, and make sure the selector lever is in
P (automatic transaxle) or in 1st gear or R
(manual transaxle):
Leaving the driver's seat without switching
the ignition off, setting the parking brake,
and shifting the selector lever to P
(automatic transaxle) or to 1st gear or R
(manual transaxle) is dangerous.
Unexpected vehicle movement could occur
which could result in an accident.
In addition, if your intention is to leave the
vehicle for even a short period, it is
important to switch the ignition off, as
leaving it in another position will disable
some of the vehicle's security systems and
run the battery down.
NOTE
(Locked steering wheel)
If the push button start indicator light
(green) is flashing and the beep sound is
heard, this indicates that the steering
wheel is not unlocked. To unlock the
steering wheel, press the push button start
while moving the steering wheel left and
right.
ACC (Accessory)
Some electrical accessories will operate
and the indicator light (amber) illuminates.
When Driving
Start/Stop Engine
4-4
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

This is for improved exhaust gas
purification and does not indicate any
parts defect.
1. Make sure you are carrying the key.
2. Occupants should fasten their seat belts.
3. Make sure the parking brake is on.
4. Continue to press the brake pedal firmly until the engine has completely
started.
5. (Manual transaxle)
Continue to press the clutch pedal
firmly until the engine has completely
started.
(Automatic transaxle)
Put the vehicle in park (P). If you must
restart the engine while the vehicle is
moving, shift into neutral (N).
NOTE
•(Manual transaxle)
The starter will not operate if the
clutch pedal is not depressed
sufficiently.
•(Automatic transaxle)
The starter will not operate if the
selector lever is not in P or N and
the brake pedal is not depressed
sufficiently.
6. Verify that the KEY indicator light
(green) (if equipped ) in the instrument
cluster and the push button start
indicator light (green) illuminate.
Indicator light
Push button start
NOTE
•If the push button start indicator
light (green) flashes, make sure that
the key is being carried (for vehicles
with a type A instrument cluster
(page 4-42), messages are
displayed in the instrument cluster).
•If the push button start indicator
light (green) flashes with the key
being carried, touch the key to the
push button start and start the
engine (for vehicles with a type A
instrument cluster (page 4-42),
messages are displayed in the
instrument cluster). Refer to Engine
Start Function When Key Battery is
Dead on page 4-9.
When Driving
Start/Stop Engine
4-6
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

CAUTION
If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) flashes, this
could indicate a problem with the
engine starting system. This may
prevent the engine from starting or
from switching the ignition to ACC or
ON (for vehicles with a type A
instrument cluster (page 4-42),
messages are displayed in the
instrument cluster). Have your vehicle
inspected at an expert repairer, we
recommend an Authorised Mazda
Repairer as soon as possible.
NOTE
•Under the following conditions, the
KEY warning light (red) flashes after
the push button start is pressed. This
informs the driver that the push
button start will not switch to ACC,
even if it is pressed from off (for
vehicles with a type A instrument
cluster (page 4-42), messages are
displayed in the instrument cluster).
•The key battery is dead.
•The key is out of operational
range.
•The key is placed in areas where it
is difficult for the system to detect
the signal (page 3-6).
•A key from another manufacturer
similar to the key is in the
operational range.
•(Forced engine starting method)
If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) flashes, this
could indicate that the engine may
not start using the usual starting
method (for vehicles with a type A
instrument cluster (page 4-42),
messages are displayed in the
instrument cluster). Have your
vehicle inspected at an expert
repairer, we recommend an
Authorised Mazda Repairer as soon
as possible. If this occurs, the engine
can be force-started. Press and hold
the push button start until the engine
starts. Other procedures necessary
for starting the engine, such as
having the key in the cabin, and
depressing the clutch pedal (manual
transaxle) or the brake pedal
(automatic transaxle) are required.
•When the engine is force-started, the
KEY warning light (red) (if
equipped) remains illuminated and
the push button start indicator light
(amber) remains flashing.
•(Automatic transaxle)
When the selector lever is in the
neutral (N) position, the KEY
indicator light (green) (if equipped)
and the push button start indicator
light (green) do not illuminate.
7. Press the push button start after both
the KEY indicator light (green) (if
equipped) in the ins trument cluster and
the push button start indicator light
(green) illuminate.
When Driving
Start/Stop Engine
4-7
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

NOTE
•After starting the engine, the push
button start indicator light (amber)
turns off and the ignition switches to
the ON position.
•(SKYACTIV-G 2.0, SKYACTIV-G
2.5)
After pressing the push button start
and before the engine starts, the
operation sound of the fuel pump
motor from near the fuel tank can be
heard, however, this does not
indicate a malfunction.
•(SKYACTIV-D 2.2)
•The starter does not rotate until
the glow indicator light turns off.
•If the ignition is left switched ON
for a long period of time without
the engine running after the glow
plugs are warmed up, the glow
plugs may warm up again which
will illuminate the glow indicator
light.
•When starting the engine, do not
release the clutch pedal (manual
transaxle) or the brake pedal
(automatic transaxle) until the
glow indicator light in the
instrument cluster turns off and
the engine starts, after pressing
the push button start.
•If the clutch pedal (manual
transaxle) or the brake pedal
(automatic transaxle) is released
before the engine starts, depress
the clutch pedal (manual
transaxle) or the brake pedal
(automatic transaxle) again and
press the push button start to start
the engine.
8. After starting the e ngine, let it idle for
about ten seconds (Prohibited in
Germany).
NOTE
•(Germany)
Drive immediately after starting the
engine. However do not use high
engine speeds until reaching the
operating temperature.
•(SKYACTIV-G 2.0, SKYACTIV-G
2.5)
•Whether the engine is cold or
warm, it should be started without
the use of the accelerator.
•If the engine does not start the first
time, refer to Starting a Flooded
Engine under Emergency Starting.
If the engine still does not start,
have your vehicle inspected by an
Authorised Mazda Repairer (page
7-35).
•(SKYACTIV-D 2.2)
If the ambient temperature is lower
than about
－ 10 °C (14 °F), the
maximum engine speed may not be
attained for about three minutes
after the engine starts to protect the
engine.
When Driving
Start/Stop Engine
4-8
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•(Manual transaxle vehicle with
i-stop function)
If the engine has stopped due to
stalling, it can be restarted by
depressing the clutch pedal within 3
seconds of the engine stopping.
The engine cannot be restarted even
if the clutch pedal is depressed under
the following conditions:
•The driver's door is open.
•The driver's seat belt is
unfastened.
•The clutch pedal is not released
completely after the engine stalled.
•The clutch pedal is depressed with
the engine not stopped completely.
▼Engine Start Function When Key
Battery is Dead
CAUTION
When starting the engine by holding the
transmitter over the push button start due
to a dead key battery or a malfunctioning
key, be careful not to allow the following,
otherwise the signal from the key will not
be received correctly and the engine may
not start.

Metal parts of other keys or metal objects
touch the key.
Spare keys or keys for other vehicles
equipped with an immobilizer system
touch or come near the key.
Devices for electronic purchases, or
security passage touch or come near the
key.
If the engine cannot be started due to a
dead key battery, the engine can be started
using the following procedure:
1. Continue to depress the brake pedal firmly until the engine has completely
started.
2. (Manual transaxle)
Continue to depress the clutch pedal
firmly until the engine has completely
started.
3. Verify that the push button start
indication light (green) flashes.
4. Touch the push button start using the
backside of the ke y (as shown) while
the push button start indicator light
(green) flashes.

Push button start
Indicator light
Key
When Driving
Start/Stop Engine
4-9
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

NOTE
When touching the push button start
using the backside of the key as shown
in the illustration, touch the push
button start with the lock switch side of
the key facing up.
5. Verify that the push button start
indicator light (green) turns on.
6. Press the push button start to start the engine.
NOTE
•The engine cannot be started unless
the clutch pedal is fully depressed
(manual transaxle) or the brake
pedal is fully depressed (automatic
transaxle).
•If there is a malfunction with the
push button start function, the push
button start indica tor light (amber)
flashes. In this ca se, the engine may
start, however, have the vehicle
checked at an expert repairer, we
recommend an Authorised Mazda
Repairer as soon as possible.
•If the push button start indicator
light (green) does not illuminate,
perform the operation from the
beginning again. If it does not
illuminate, have the vehicle checked
at an expert repairer, we recommend
an Authorised Mazda Repairer.
•To switch the ignition position
without starting the engine, perform
the following operations after the
push button start indicator light
(green) turns on.
1. Release the clutch pedal (manual transaxle) or brake pedal
(automatic transaxle).
2. Press the push button start to
switch the igniti on position. The
ignition switches in the order of
ACC, ON, and off each time the
push button start is pressed. To
switch the ignition position
again, perform the operation
from the beginning.
▼ Emergency Operation for Starting
the Engine
If the KEY warning ligh
t (red) illuminates,
or the push button start indicator light
(amber) flashes, this could indicate that
the engine may not s tart using the usual
starting method (for vehicles with a type A
instrument cluster (page 4-42), messages
are displayed in the instrument cluster).
Have your vehicle inspected at an expert
repairer, we recommend an Authorised
Mazda Repairer as soon as possible. If this
occurs, the engine can be force-started.
Press and hold the push button start until
the engine starts. Other procedures
necessary for starting the engine such as
having the key in the cabin, and
depressing the clutch pedal (manual
transaxle) or the bra ke pedal (automatic
transaxle) are required.
When Driving
Start/Stop Engine
4-10
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

i-stop*
The i-stop function automatically stops the engine when the vehicle is stopped at a traffic
light or stuck in traffic, and then restarts the engine automatically to resume driving. The
system provides improved fuel economy, reduced exhaust gas emis sions, and eliminates
idling noise while the engine is stopped.
Engine idle stopping and restarting
NOTE
•The i-stop indicator light (green) turn s on under the following conditions:
•When engine idling is stopped.
•Engine idling stop conditions are met while the vehicle is being driven.
•The i-stop indicator light (green) turns off when the engine is restarted.
Manual transaxle
(AUTOHOLD operation turned off)
1. Stop the vehicle by depressing the brake pedal and then the c lutch pedal.
2. While depressing the clutch pe dal, shift the shift lever to the neutral position. Engine
idling stops after the clutch pedal is released.
3. (SKYACTIV-G 2.0, SKYACTIV-G 2.5)
The engine restarts automatically when you depress the clutch p edal or start to release it.
NOTE
The engine restart timing varies depending on the brake pedal depression force.
(SKYACTIV-D 2.2)
The engine restarts automatically when the clutch pedal is depressed.
When Driving
Start/Stop Engine
4-12*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

(When the vehicle is stopped by the AUTOHOLD function)
1. Bring the vehicle to a complet e stop by depressing the brake pedal first and then the
clutch pedal.
2. While depressing the clutch ped al, shift the shift lever to neutral. After releasing your
foot from the clutch pedal, engi ne idling stops and continues to be stopped even if the
brake pedal is released.
3. The engine restarts automatically when the clutch pedal is de pressed.
Automatic transaxle
(AUTOHOLD operation turned off and When not using Mazda Radar C ruise Control
with Stop & Go function (MRCC with Stop & Go function))
1. Engine idling stops when the b rake pedal is depressed while the vehicle is driven (except
for driving in the R or M positi on second gear fixed mode) and the vehicle is stopped.
2. The engine restarts automatical ly when the brake pedal is released with the selector lever
in the D or M position (not in second gear fixed mode).
3. If the selector lever is in the N or P position, the engine does not restart when the brake
pedal is released. The engine restarts when the brake pedal is depressed again or the
selector lever is shifted to the D, M (not in second gear fixed mode) or the R position.
(For the purposes of safety, always keep the brake pedal depres sed when shifting the
selector lever while engine idling is stopped.)
(When the vehicle is s topped by the Mazda Radar Cruise Control with Stop & Go
function (MRCC with St op & Go function) stop hold control)
1. When the vehicle is stopped by the Mazda Radar Cruise Control with Stop & Go
function (MRCC with Stop & Go fun ction), engine idling stops and continues to be
stopped without depressing the brake pedal.
2. When the accelerator pedal is depressed or the RES switch is operated while the vehicle
is kept stopped by the Mazda Radar Cruise Control with Stop & G o function (MRCC
with Stop & Go function), the engine automatically restarts. Th e engine restarts
automatically when the accelerator pedal is depressed with the selector lever in the D/M
position (not in second gear fixed mode).
(When the vehicle is stopped by the AUTOHOLD function)
1. When the brake pedal is depressed while the vehicle is being driven (except for driving
in the R or M position second gear fixed mode) and the vehicle is brought to a stop, the
i-stop function will operate and i t continues to operate even if the brake is released.
2. The engine restarts automatically when the accelerator pedal is depressed with the
selector lever in the D/M position (not in second gear fixed mo de).
3. If the selector lever is in the N or P position, the engine does not restart when the brake pedal is released. The engine restarts when the brake pedal is depressed again or the
selector lever is shifted to the D, M (not in second gear fixed mode) or the R position.
(For the purposes of safety, always keep the brake pedal depres sed when shifting the
selector lever while engine idling is stopped.)
When Driving
Start/Stop Engine
4-13
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2