2017 KIA OPTIMA PLUG-IN HYBRID service

EMERGENCY STARTING
Connect cables in numerical order and
disconnect in reverse order. ❈ (A): Jumper cables
(B): Booster battery
(C): Discharged battery
Jump starting
Jump starting can be dangerous if done
incorrectly. Therefore, to avoid harm to yourself or damage to your vehicle or
battery, follow the jump starting pro‐
cedures. If in doubt, we strongly rec‐ ommend that you have a competent
technician or towing service jump start
your vehicle.
CAUTION
Use only a 12-volt jumper system.You can damage a 12-volt startingmotor, ignition system, and otherelectrical parts beyond repair by useof a 24- volt power supply (eithertwo 12-volt batteries in series or a24-volt motor generator set).
WARNING
nBattery
Never attempt to check the electro‐lyte level of the battery as this maycause the battery to rupture or ex‐plode causing serious injury.
WARNING
nBattery
(Continued)
(Continued)
•Keep all flames or sparks awayfrom the battery. The batteryproduces hydrogen gas which mayexplode if exposed to flame orsparks.If these instructions are not fol‐lowed exactly, serious personal in‐jury and damage to the vehiclemay occur! If you are not sure howto follow this procedure, seekqualified assistance. Automobilebatteries contain sulfuric acid. Thisis poisonous and highly corrosive.When jump starting, wear protec‐tive glasses and be careful not toget acid on yourself, your clothingor on the vehicle.
•Do not attempt to jump start thevehicle if the discharged battery isfrozen or if the electrolyte level islow; the battery may rupture orexplode.
•Do not allow the (+) and (-) jumpercables to touch. It may causesparks.
•The battery may rupture or ex‐plode when you jump start with alow or frozen battery.

8-05
8
What to do in an emergency

When the tire pressure monitoring sys‐
tem warning indicators are illuminated and warning massage displayed on the
cluster LCD display, one or more of
your tires is significantly under-infla‐ ted. The low tire pressure position tell‐
tale light will indicate which tire is sig‐
nificantly under-inflated by illuminating the corresponding position light.
If either telltale illuminates, immediate‐
ly reduce your speed, avoid hard cor‐
nering and anticipate increased stop‐ ping distances. You should stop and
check your tires as soon as possible. In‐
flate the tires to the proper pressure as
indicated on the vehicle’s placard or tire inflation pressure label located on the
driver’s side center pillar outer panel. If
you cannot reach a service station or if the tire cannot hold the newly added
air, replace the low pressure tire with a
spare tire.
If you drive the vehicle for about 10 mi‐ nutes at speeds above 25 km/h after
replacing the low pressure tire with the
spare tire, one of the following will hap‐ pen: • The TPMS malfunction indicator may
blink for approximately 1 minute and
then remain continuously illuminated
because the TPMS sensor is not
mounted on the spare wheel. (changed tire equipped with a sensor
not in the vehicle)
• The TPMS malfunction indicator will remain continuously illuminated while
driving because the TPMS sensor is
not mounted on the spare wheel. (changed tire equipped with a sensor
in the vehicle)
CAUTION
In winter or cold weather, the lowtire pressure telltale may illuminateif the tire pressure was adjusted tothe recommended tire inflation pres‐sure in warm weather. It does notmean your TPMS is malfunctioningbecause the decreased temperatureleads to a lowering of tire pressure.When you drive your vehicle from awarm area to a cold area or from acold area to a warm area, or theoutside temperature is higher orlower, you should check the tire in‐flation pressure and adjust the tires
(Continued)
(Continued)
to the recommended tire inflationpressure.
WARNING
nLow pressure damage
Significantly low tire pressure makesthe vehicle unstable and can contrib‐ute to loss of vehicle control and in‐creased braking distances.Continued driving on low pressuretires can cause the tires to overheatand fail.
TPMS (Tire Pressure
Monitoring System)
malfunction indicator
The TPMS malfunction indi‐ cator will illuminate after it blinks for
approximately one minute when there is a problem with the Tire Pressure
Monitoring System.
We recommend that the system be
checked by an authorized Kia dealer to determine the cause of the problem.

8-11
8
What to do in an emergency

NOTICE
If there is a malfunction with the
TPMS, the low tire pressure position
telltale will not be displayed even
though the vehicle has an under-in‐
flated tire.
CAUTION
•The TPMS malfunction indicatormay blink for approximately 1 mi‐nute and then remain continuouslyilluminated if the vehicle is movingaround electric power supply ca‐bles or radio transmitters such asat police stations, government andpublic offices, broadcasting sta‐tions, military installations, air‐ports, or transmitting towers, etc.This can interfere with normal op‐eration of the Tire Pressure Moni‐toring System (TPMS).
(Continued)
(Continued)
•The TPMS malfunction indicatormay blink for approximately 1 mi‐nute and then remain continuouslyilluminated if snow chains are usedor some separate electronic devi‐ces such as notebook computer,mobile charger, remote starter ornavigation etc., are used in the ve‐hicle.This can interfere with normal op‐eration of the Tire Pressure Moni‐toring System (TPMS).
Changing a tire with TPMS
If you have a flat tire, the low Tire
Pressure and Position telltales will come on. We recommend that the sys‐
tem be checked by an authorized Kia
dealer.
CAUTION
We recommend that you use thesealant approved by Kia.The sealant on the tire pressuresensor and wheel shall be eliminatedwhen you replace the tire with a newone.
Each wheel is equipped with a tire pres‐
sure sensor mounted inside the tire be‐ hind the valve stem. You must use
TPMS specific wheels. It is recommen‐
ded that you have your tires serviced by an authorized Kia dealer.
If you drive the vehicle for about 10 mi‐
nutes at speeds above 25 km/h after
replacing the low pressure tire with the spare tire, one of the following will hap‐
pen: • The TPMS malfunction indicator may blink for approximately 1 minute and
then remain continuously illuminated because the TPMS sensor is not
mounted on the spare wheel.
(changed tire equipped with a sensor
not in the vehicle)
• The TPMS malfunction indicator will remain continuously illuminated whiledriving because the TPMS sensor is
not mounted on the spare wheel.
(changed tire equipped with a sensor
in the vehicle)
What to do in an emergency
8-12

WARNING
nCarbon monoxide
Carbon monoxide poisoning and suf‐focation is possible if the engine isleft running in a poorly ventilated orunventilated location (such as insidea building).
Distributing the sealant
11. Immediately drive approximately7~10 km (4~6 miles or, about 10
min) to evenly distribute the seal‐
ant in the tire.
CAUTION
Do not exceed a speed of 80 km/h(50 mph). If possible, do not fall be‐low a speed of 20 km/h (12 mph).While driving, if you experience anyunusual vibration, ride disturbanceor noise, reduce your speed anddrive with caution until you cansafely pull off of the side of theroad. Call for road side service ortowing.
(Continued)
(Continued)
When you use the Tire Mobility Kit,the tire pressure sensors and wheelmay be stained by sealant. There‐fore, remove the tire pressure sen‐sors and wheel stained by sealantand we recommend to have it in‐spected by an authorized Kia dealer.
Checking the tire inflation
pressure
0+')
1. After driving approximately 7~10 km (4~6 miles, or about 10
minutes), stop at a suitable loca‐
tion. 2. Connect connection hose (10) of
the compressor directly to the tire
valve.
3. Connect between compressor and the vehicle battery using the cable
and connectors.
4. Adjust the tire inflation pressure to 200 kPa (29 psi). With the ignition
switched on, proceed as follows. -
To increase the inflation pres‐sure: Switch on the compressor,
position I. To check the current
inflation pressure setting, briefly switch off the compressor.
WARNING
Do not let the compressor run formore than 10 minutes, otherwisethe device will overheat and may bedamaged.
-To reduce the inflation pressure:
Press the button (9) on the com‐
pressor.

8-19
8
What to do in an emergency

CAUTION
If the inflation pressure is not main‐tained, drive the vehicle a secondtime, refer to Distributing the seal‐ant. Then repeat steps 1 to 4.Use of the TMK may be ineffectualfor tire damage larger than approxi‐mately 4 mm (0.16 in).We recommend that you contact anauthorized Kia dealer if the tire can‐not be made roadworthy with theTire Mobility Kit.
WARNING
The tire inflation pressure must beat least 200 kPa (29 psi). If it is not,do not continue driving.Call for road side service or towing.
Notes on the safe use of the
Tire Mobility Kit
• Park your car at the side of the roadso that you can work with the TMK
away from moving traffic. Place your warning triangle in a prominent place
to make passing vehicles aware of
your location. • To be sure your vehicle will not move,
even when you're on fairly level
ground, always set your parking brake.
• Only use the TMK for sealing/inflation passenger car tires. Do not use on
motorcycles, bicycles or any other
type of tires.
• Do not remove any foreign objects such as nails or screws -that have
penetrated the tire.
• Before using the TMK, read the pre‐ cautionary advice printed on the seal‐ ant bottle!
• Provided the car is outdoors, leave the engine running. Otherwise oper‐
ating the compressor may eventually
drain the car battery.
• Never leave the TMK unattended while it is being used.
• Do not leave the compressor running for more than 10 min. at a time or it
may overheat.
• Do not use the TMK if the ambient temperature is below -30°C (-22°F).
• When the tire and wheel are dam‐ aged, do not use Tire Mobility Kit foryour safety.
Technical data
System voltage: DC 12 V
Working voltage: DC 10 - 15 VAmperage rating: max. 15 A
Suitable for use at temperatures:
-30 ~ +70°C (-22 ~ +158°F)
Max. working pressure: 6 bar (87 psi)Size
Compressor: 168 x 150 x 68 mm (6.6 x 5.9 x 2.7 in)
Sealant bottle: 104 x 85 ø mm
(4.1 x 3.3 ø in.)
Compressor weight: 1.05 kg (2.31 lbs)
Sealant volume: 300 ml (18.3 cu. in.) ❈ Sealant and spare parts can be ob‐
tained and replaced at an author‐
ized vehicle or tire dealer. Empty
sealant bottles may be disposed of
at home. Liquid residue from the
sealant should be disposed of by
your vehicle or tire dealer or in ac‐
cordance with local waste disposal
regulations.
What to do in an emergency
8-20

TOWING
Towing service
0+'-
If emergency towing is necessary, we
recommend having it done by an au‐ thorized Kia dealer or a commercial
tow-truck service. Proper lifting and
towing procedures are necessary to prevent damage to the vehicle. The use
of wheel dollies (1) or flatbed is recom‐
mended. It is acceptable to tow the vehicle with
the rear wheels on the ground (without
dollies) and the front wheels off the
ground.
If any of the loaded wheels or suspen‐ sion components are damaged or the
vehicle is being towed with the front
wheels on the ground, use a towing dolly under the front wheels.
When being towed by a commercial
tow truck and wheel dollies are not
used, the front of the vehicle should al‐ ways be lifted, not the rear.
NOTICE
If the EPB does not release normally,
we recommend that you contact an
authorized Kia dealer.
)9%
)9%
CAUTION
•Do not tow the vehicle backwardswith the front wheels on theground as this may cause damageto the vehicle.
•Do not tow with sling-type equip‐ment. Use wheel lift or flatbedequipment.
When towing your vehicle in an emer‐
gency without wheel dollies: 1. Set the ignition switch in the ACC position.

8-21
8
What to do in an emergency

If towing is necessary, we recommendyou to have it done by an authorizedKia dealer or a commercial tow truckservice.
If towing service is not available in an
emergency, your vehicle may be tem‐ porarily towed using a cable or chain
secured to the emergency towing hook
under the front (or rear) of the vehicle. Use extreme caution when towing the
vehicle. A driver must be in the vehicle
to steer it and operate the brakes.
Towing in this manner may be done on‐ ly on hard-surfaced roads for a short
distance and at low speed. Also, the
wheels, axles, power train, steering and brakes must all be in good condition. • Do not use the tow hooks to pull a vehicle out of mud, sand or other
conditions from which the vehicle
cannot be driven out under its own
power.
• Avoid towing a vehicle heavier than the vehicle doing the towing.
• The drivers of both vehicles should communicate with each other fre‐
quently.
CAUTION
•Attach a towing strap to the towhook.
•Using a portion of the vehicle oth‐er than the tow hooks for towingmay damage the body of your ve‐hicle.
•Use only a cable or chain specifi‐cally intended for use in towingvehicles. Securely fasten the cableor chain to the towing hook provi‐ded.
• Before emergency towing, check if the hook is not broken or damaged.
• Fasten the towing cable or chain se‐ curely to the hook.
• Do not jerk the hook. Apply it steadily and with even force.
• To avoid damaging the hook, do not pull from the side or at a vertical an‐
gle. Always pull straight ahead.
WARNING
Use extreme caution when towingthe vehicle.•Avoid sudden starts or erratic driv‐ing maneuvers which would placeexcessive stress on the emergencytowing hook and towing cable orchain. The hook and towing cableor chain may break and cause seri‐ous injury or damage.
•If the disabled vehicle is unable tobe moved, do not forcibly continuethe towing. We recommend thatyou contact an authorized Kiadealer or a commercial tow truckservice for assistance.
•Tow the vehicle as straight aheadas possible.
•Keep away from the vehicle duringtowing.

8-23
8
What to do in an emergency

(Continued)
1.Stop the vehicle and shift thetransmission in to "P" position,and then depress the parkingbrake. To ventilate smoke from afire, open the windows if possi‐ble.
2.Turn off the Hybrid system bypushing the Engine Start/StopButton.
3.Leave the vehicle and evacuateto the safety place.
4.Call emergency services for helpand let them know the vehicle isa Hybrid vehicle.
If you have an extinguisher, extin‐guish a fire carefully.Do not touch high voltage cables,connectors and package modules.High voltage components are orangein color.Exposed cables or wires may be visi‐ble inside or outside of the vehicle.Never touch the wires or cables, be‐cause an electrical shock may occurcausing injury or death.
WARNING
If a submersion in water occurs:If your vehicle was flooded and hassoaked carpeting or water on theflooring, you should not try to startthe Hybrid system. Never touch thehigh voltage cables, connectors andpackage modules, because an elec‐trical shock may occur causing injuryor death. High Voltage cables are or‐ange in color.We recommend that the car towedto an authorized Kia dealer.
What to do in an emergency
8-26