2017 INFINITI QX30 light

NOTE
HD Radio reception needs to be activated to re-
ceive HD Radio broadcasts. This enables you to
receive radio broadcasts digitally (where avail-
able), providing a better quality sound with clear
reception. When this feature is not activated or
HD Radio broadcasts are not available, you will
receive analog radio (AM/FM broadcasts).
Radio source control
There are 2 elements used in the preset list area
that are associated with radio source:
1Highlight for INFINITI controller opera-
tion.
2(With triangle) Indicator of current se-
lected preset station.
Radio operation
Radio activation and band selection:
Pushor select the preferred radio band
(AM, FM or SXM) from the audio source list to
turn on the radio. Each timeis pushed,
the radio band will change.
For details, seeSelecting audio sourcelater in
this section.NOTE
When the stereo broadcast signal is weak, the
radio will automatically change from stereo to
monaural reception.
Seeking stations/channels
:
AM and FM Radio
Pushto tune from low to
high or high to low frequencies and to stop at
the next broadcasting station.
SiriusXM Satellite Radio
Pushto tune to the first
channel of the next or previous category.
Scan tuning
:
To tune the stations/channels, touch [Control]
on the display and touch [Scan]. The stations/
channels will be tuned form low to high fre-
quencies and stop at each broadcasting
station/channel for 5 seconds. Touching [Scan]
again during this 5 second period will stop scan
tuning and the radio will remain tuned to that
station/channel.
Presetting
:
Up to 36 stations/channels can be registered
for AM, FM and SXM in the preset list.
1. Select a radio band (AM, FM or SXM).
NAA1717
4-68Display screen, heater and air conditioner, and audio system

Two USB (iPod) connectors are located on the
center console box.
USB (Universal Serial Bus) connection port/
iPod
The battery of the iPod will be charged while the
device is connected to the vehicle if the iPod
supports USB connection charging.
Depending on the model and firmware version
of the iPod, the display on the iPod shows an
INFINITI or Accessory Attached screen when the
connection is completed. When the iPod is
connected to the vehicle, the iPod music library
can only be operated using the vehicle audio
controls.
Compatibility
:
Made for
•iPod touchR(5th generation)
•iPod touchR(4th generation)
•iPod touchR(3rd generation)
•iPod touchR(2nd generation)
•iPod touchR(1st generation)
•iPod touchR
•iPodRwith video
•iPod classicR
•iPod nanoR(7th generation)
•iPod nanoR(6th generation)
•iPod nanoR(5th generation)
•iPod nanoR(4th generation)
•iPod nanoR(3rd generation)
•iPod nanoR(2nd generation)
•iPod nanoR(1st generation)
•iPhoneR6 Plus
•iPhoneR6
•iPhoneR5S
•iPhoneR5
•iPhoneR4S
•iPhoneR4
•iPhoneR3GS
•iPhoneR3G
•iPhoneR
The iPod touchRmay not respond quickly with
the system in some cases.
Make sure that the iPod
Rfirmware is up-
dated.The Lightning
TMconnector works with iPhone
R5, iPhoneR5S, iPhoneR6, iPhoneR6
Plus, iPod touch
R(5th generation), and iPod
nano
R(7th generation).
The 30-pin connector works with iPhone
R4S,
iPhone
R4, iPhoneR3GS, iPhoneR3G,
iPhone
R, iPod touchR(1st through 4th
generation), iPod classic
R, and iPod nanoR(1st through 6th generation).
USB works with iPhone
R5, iPhoneR4S,
iPhone
R4, iPhoneR3GS, iPhoneR3G,
iPhone
R, iPod touchR(1st through 5th
generation), iPod classi
Rc, and iPod nanoR(1st through 7th generation).
4-76Display screen, heater and air conditioner, and audio system

DISC/USB MEMORY DEVICE CARE AND
CLEANING
DISCS
•Handle a disc by its edges. Never touch the
surface of the disc. Do not bend the disc.
•Always place discs in their storage cases
when they are not being used.
•To clean a disc, wipe the surface from the
center to the outer edge using a clean, soft
cloth. Do not wipe the disc using a circular
motion.
Do not use a conventional record cleaner or
alcohol intended for industrial use.
•The inner and outer edges of a new disc may
be rough. Remove the rough edges by rub-
bing the inner and outer edges with the side
of a pen or pencil as illustrated.
USB MEMORY DEVICE
•Never touch the terminal portion of the USB
memory device.
•Do not place heavy objects on the USB
memory device.
•Do not store the USB memory device in very
humid locations.
•Do not expose the USB memory device to
direct sunlight.
•Do not spill any liquids on the USB memory
device.
Refer to the owner’s manual for the USB
memory device for details.
SAA0451Z
4-84Display screen, heater and air conditioner, and audio system

GIVING VOICE COMMANDS
1. Push<>located on the steering wheel.
2. A list of commands appears on the screen,
and the system provides a voice menu
prompt.
When this screen is displayed, almost all of
the commands can be recognized. Available
commands for each categories can be shown
on the right side of the screen. Highlight a
category listed in the left side of the screen
with the INFINITI controller to find your pre-
ferred command.
Selecting a category by touching the screen
or pushing<
/OK>will execute the
command. After executing the category com-
mand, only the commands related to the
selected category can be recognized.
Command listin the5. Starting and driv-
ingsection3. After the tone sounds and the icon on the
screen changes from
to, speak a
command. You can also select a command
by directly touching the screen.
The Voice Recognition system will pause
operation when the INFINITI controller is
moved. To resume operation, push<
>
on the steering wheel.
4. Continue to follow the voice menu prompts
and speak after the tone sounds until the
preferred operation is completed.
To cancel the voice command, push and hold<
>.
You can interrupt the voice prompt at any time
by pushing<
>.
Operating tips
•Speak a command after the tone.
•If the command is not accepted, the system
announces, “Please say again”. Repeat the
command in a clear voice.
•Push<>on the steering-wheel switch
once to return to the previous screen.
•Voice commands spoken from the passen-
ger seat cannot be recognized.
NAA1732
4-106Display screen, heater and air conditioner, and audio system

NOTE
The Fuel Prices, Weather Forecast, Current
Weather, Sports Scores and Traffic Information
will not operate without a subscription to
SiriusXM Radio.
VOICE RECOGNITION SETTINGS
Voice recognition functions can be set.
1. Push

SYSTEM UNIT
Liquid crystal display
Symptom Possible cause Possible solution
The screen is too dark. The cabin temperature is too low. Wait until the cabin temperature becomes moderate.
Screen brightness is set to the maximum darkness. Adjust the brightness setting of the screen.
Screen settingsearlier in this section
The screen is too bright. Screen brightness is set to the maximum brightness. Adjust the brightness setting of the screen.
Screen settingsearlier in this section
A small black spot or a small bright spot appears on the
screen.This is a phenomenon typical to liquid crystal
displays.This is not a malfunction.
A dot or stripe pattern appears on the screen. Electromagnetic waves that are generated from neon
billboards, high voltage electric power cables, ham
radios or other radio devices equipped to other
vehicles may adversely affect the screen.This is not a malfunction.
Image lag appears on the screen. Phenomenon typical of liquid crystal displays. This is not a malfunction.
Image motion displayed on the screen is slow. The cabin temperature is below 32
oF(0oC). Wait until the in-cabin temperature rises to above
32oF(0oC).
When looking at the screen from an angle, the screen
lightens or darkens.This is a phenomenon typical to liquid crystal
displays.Adjust the brightness setting of the screen.
Screen settingsearlier in this section
The screen turns blue or an error message is displayed
on the display.The SD card is not inserted into the slot correctly. If the SD card containing map data is accidentally
removed, after re-inserting the SD card containing
map data into the slot, place the ignition switch in
the OFF position and then back in the ON position
again.
A system malfunction has occurred. It is recommended you contact an INFINITI retailer
for inspection.
Display screen, heater and air conditioner, and audio system4-125

Functional:
Symptom Possible cause Possible solution
Keep losing my local stations. The digital coverage is slightly less than the analog
signal coverage.Verify correct operation on another station. This is
expected behavior.
Shadowing (urban/terrain) can cause reduced digital
coverage.Verify correct operation on another station.
Some data fields are blank. Text information is sent at the broadcaster’s
discretion.Verify correct operation on another station. Report
station issues.
Text information is truncated / appears to be more
available.The display is limited to a fixed number of characters
and more data is being sent than can be shown.This is intended behavior. Refer to the Owner’s
Manual for ability to access addition.
AM reception changes at night. AM stations are required by the government (FCC) to
lower their power at night.This is not a malfunction.
Display screen, heater and air conditioner, and audio system4-127

MONITOR SYSTEM
Symptom Possible cause Possible solution
The image on the display is not clear. The front of the camera lens is dirty. Gently wipe off the dirt with a damp soft cloth.
Moisture drops such as rain or snow form on the
camera lens.Gently wipe off the drops with a soft cloth.
Light such as sunlight or a headlight beam from
another vehicle directly enters the camera.This is not a malfunction. It will return to normal
when the light disappears.
Moisture condensation occurs in the camera lens due
to rapid temperature change.This is not a malfunction. It will return to normal after
driving for short period of time.
Objects on the display may not be clear in a dark
place or at night.Adjust the brightness or the contrast settings of the
screen.
The image on the display flickers. The vehicle is under fluorescent light. This is not a malfunction.
The colors of the object on the display look different
from those of the actual object.This is a typical phenomenon for cameras. This is not a malfunction.
Image does not appear on the display. The shift lever is not shifted to the R (Reverse)
position.Shift the shift lever to the R (Reverse) position.
[Automatic Display with Sonar] is OFF. Set [Automatic Display with Sonar] to ON.
The image appears on the display from the wrong
angle.The lift gate is open. Close the lift gate.
The image on the display is not clearly visible. Strong light or reflected light enters the camera. This is not a malfunction.
The sensor is not detective. There is ice or snow on the sensor. Flush out ice and snow with warm water.
There is dirt, mud or wax on the sensor. Gently wipe off the dirt with a damp soft cloth.
Vertical lines appear on the image. Strong reflected light from the bumper enters the
camera.This is not a malfunction.
Display screen, heater and air conditioner, and audio system4-137