2017 INFINITI QX30 light

To unlock the vehicle:touch the inner surface of
the door handle.
To lock the vehicle:touch sensor surface
1.or
2.
Make sure that you do not touch the inner
surface of the door handle.
Convenience closing feature:touch recessed
sensor surface
1for an extended period. (See
Convenience closing featurein the
2. Instruments and controlssection).To unlock the lift gate: press the lift gate switch
1.
When unlocking, the turn signals flash once
When locking, they flash three times.
NOTE
When the locator lighting is activated, it lights
up when it is dark after the vehicle is unlocked
with the intelligent key (see separate operating
instructions).
You can also set an audible signal to con firm
that the vehicle has been locked. The audible
signal can be activated or deactivated using the
on-board computer (seeActivating/
deactivating the acoustic locking confirmation
in the2. Instruments and controlssection)LOCKING WITH THE MECHANICAL KEY
The driver’s door can be locked/unlocked from
outside using the mechanical key if the battery
is dead.
To lock the door, insert the mechanical key into
the driver’s door key cylinder and turn it to-
wards the front of the vehicle
1.
To unlock the door, turn the key towards the
rear of the vehicle
2.
SeeMechanical keyearlier in this section for
instructions on accessing the Intelligent Key
system mechanical key.
NPA1489NPA1479SPA2602Z
Pre-driving checks and adjustments3-5

CHILD SAFETY REAR DOOR LOCK
The child safety lock helps prevent doors from
being opened accidentally, especially when
small children are in the vehicle.
When the switch is in the LOCK
2position, the
rear door can only be opened from the outside.
LIFT GATE LOCK
To open the lift gate, unlock it first with one of
the following operations, then push the button
1.
•Push thebutton on the key or Intelli-
gent Key (if equipped). SeeINFINITI intelli-
gent key systemlater in this section.
•Unlock all the doors using the key.
To close the lift gate, pull it down until it
securely locks.
1Locks the vehicle.
2Unlocks the vehicle.
3Panic button.
WARNING
•Radio waves could adversely affect electric
medical equipment. Those who use a pace-
maker should contact the electric medical
equipment manufacturer for the possible in-
fluences before use.
•The Intelligent Key transmits radio waves
when the buttons are pushed. The FAA ad-
vises that the radio waves may affect air-
craft navigation and communication sys-
tems. Do not operate the Intelligent Key
while on an airplane. Make sure that the
buttons are not operated unintentionally
when the unit is stored for a flight.
NIC2641NPA1479NPA1493
INFINITI INTELLIGENT KEY SYSTEM
Pre-driving checks and adjustments3-7

Symptom Possible causeRemedy
The engine
cannot be
started using
the keyThe on-board
voltage is too
low
•Switch off non-essential consumers, e. g. seat heating or interior lighting, and try to start the engine again
If this does not work:
•Check the starter battery and charge it if necessary (seeBatteryin the8. Do-it-yourselfsection)
or
•Jump-start the vehicle (seeJump startingin the6. In case of emergencysection)
or
•Have the system checked. It is recommended you consult an INFINITI retailer.
You have lost
a key—
•Have the key deactivated. It is recommended you visit an INFINITI retailer for this service.•Report the loss immediately to the vehicle insurers•If necessary, have the locks changed as well
You have lost
the emer-
gency key
element
•Report the loss immediately to the vehicle insurers•If necessary, have the locks changed as well.
Pre-driving checks and adjustments3-13

1. Make sure that the windshield wipers are
switched off.
2. Pull the hood lock release lever
1, located
below the instrument panel on the driver’s
side; the hood will spring up slightly.3. Push the lever
2at the front of the hood,
to the left with your fingertips and raise the
hood.4. Insert the support rod3into the slot4on the underside of the hood.
5. When closing the hood, replace the support
rod in its original position
5, slowly lower
the hood to about8–12in.(20–30cm)
above the hood lock, then let it drop. Make
sure the hood is securely latched.
WARNING
•Make sure the hood is completely closed
and latched before driving. Failure to do so
could cause the hood to fly open and result
in an accident.
•If you see steam or smoke coming from the
engine compartment, to avoid injury do not
open the hood.
NDI1603NDI1627NDI1605
HOOD
3-14Pre-driving checks and adjustments

VANITY MIRROR
To use the front vanity mirror3, pull down the
sun visor
1and pull up the cover4.
AUTOMATIC ANTI-GLARE REAR VIEW
MIRROR
The inside mirror is designed so that it auto-
matically dims according to the intensity of the
headlights of the vehicle following you. The
automatic anti-glare feature operates only when
the ignition switch is in the ON position. It will
not operate if reverse gear is engaged or if the
interior lighting is switched on.
OUTSIDE MIRRORS
The driver’s-side outside mirror is designed so
that it automatically dims according to the inten-
sity of the headlights of the vehicle following you.
The automatic anti-glare feature operates only
when the ignition switch is in the ON position. It
will not operate if reverse gear is engaged or if
the interior lighting is switched on.
Adjusting
The outside rear view mirror remote control will
operate only when the ignition switch is in the
ACC or ON position.
1. Move the switch to select the left
1or right
mirror
2.
2. Adjust each mirror to the desired position
using the large switch
3.
Defogging
The exterior rear view mirrors will be heated
when the rear window defogger switch is oper-
ated.
NIC2676NDI1630NIC2636
MIRRORS
Pre-driving checks and adjustments3-17

Clock settings
Clock settings can be changed.
1. Push

Backing up near a projecting object
The predicted course linesAdo not touch the
object in the display. However, the vehicle may
hit the object if it projects over the actual
moving course.
Backing up behind a projecting
object
The positionCis shown further than the
position
Bin the display. However, the posi-
tion
Cis actually at the same distance as theposition
A. The vehicle may hit the object
when backing up to the position
Aif the object
projects over the actual moving course.
HOW TO PARK WITH PREDICTED
COURSE LINES
WARNING
•If the tires are replaced with different sized
tires, the predicted course line may not be
displayed correctly.
•On a snow-covered or slippery road, there
may be a difference between the predicted
course line and the actual course line.
•The displayed lines will appear slightly off
to the right because the rear view camera is
not installed in the rear center of the ve-
hicle.
•If the battery is disconnected or becomes
discharged, the predicted course lines may
be displayed incorrectly. If this occurs,
please perform the following procedures:
–Turn the steering wheel from lock to lock
while the engine is running.
–Drive the vehicle on a straight road for
more than 5 minutes.
SAA1923SAA1980
4-20Display screen, heater and air conditioner, and audio system

•Objects in the RearView Monitor will appear
visually opposite than when viewed in the
rear view and outside mirrors.
•Use the displayed lines as a reference. The
lines are highly affected by the number of
occupants, fuel level, vehicle position, road
conditions and road grade.
•Make sure that the lift gate is securely
closed when backing up.
•Do not put anything on the rear view cam-
era. The rear view camera is installed above
the license plate.
•When washing the vehicle with high-
pressure water, be sure not to spray it
around the camera. Otherwise, water may
enter the camera unit causing water con-
densation on the lens, a malfunction, fire or
an electric shock.
•Do not strike the camera. It is a precision
instrument. Otherwise, it may malfunction
or cause damage resulting in a fire or an
electric shock.The following are operating limitations and do
not represent a system malfunction:
•When the temperature is extremely high or
low, the screen may not clearly display ob-
jects.
•When strong light shines directly on to the
camera, objects may not be displayed
clearly.
•Vertical lines may be seen in objects on the
screen. This is due to strong reflected light
from the bumper.
•The screen may flicker under fluorescent
light.
•The colors of objects on the RearView Moni-
tor may differ somewhat from the actual
color of objects.
•Objects on the monitor may not be clear in a
dark environment.
•Do not use wax on the camera window. Wipe
off any wax with a clean cloth dampened
with mild detergent diluted with water.
SYSTEM MAINTENANCE
CAUTION
•Do not use alcohol, benzine or thinner to
clean the camera. This will cause discolou-
ration. To clean the camera, wipe with a
cloth dampened with diluted mild cleaning
agent and then wipe with a dry cloth.
•Do not damage the camera as the monitor
screen may be adversely affected.
If dirt, rain or snow accumulates on the camera
1, the RearView Monitor may not display
objects clearly. Clean the camera by wiping it
with a cloth dampened with a diluted mild
cleaning agent and then wiping it with a dry
cloth.
NAA1688
4-24Display screen, heater and air conditioner, and audio system