•To interrupt automatic operation: press/pull
the corresponding switch again.
NOTE
•If you press/pull the switch beyond the point
of resistance, automatic operation is started
in the corresponding direction. You can stop
automatic operation by pressing/pulling
again.
•You can continue to operate the side win-
dows after switching off the engine or remov-
ing the key. This function remains active for
five minutes or until the driver’s or front-
passenger door is opened.
•The side windows cannot be operated from
the rear when the override feature for the
side windows is activated. Locking rear side windows
:
To enable/disable the override feature for the
rear side windows, press button
2. If indicator
lamp
1is lit, operation of the rear side win-
dows is disabled. Operation is only possible
using the switches in the driver’s door. If indi-
cator lamp
1is off, operation is possible using
the switches in the rear compartment.
Passenger’s window switch
The passenger’s switch can control its corre-
sponding window.
Convenience opening feature
For vehicles with Intelligent key: you can venti-
late the vehicle before you start driving. The key
can also be used to carry out the following
functions simultaneously:
•Unlock the vehicle
•Open the side windows
NOTE
The convenience opening feature can only be
operated using the key.
The key must be in close proximity to the ve-
hicle.
NIC2716NIC2640
Instruments and controls2-73
Press and hold thebutton until the side
windows are in the desired position.
To interrupt convenience opening: release the
button.
Convenience closing feature
WARNING
When the convenience closing feature is oper-
ating, parts of the body could become trapped
in the closing area of the side window. There is
a risk of injury. Observe the complete closing
procedure when the convenience closing fea-
ture is operating. When closing make sure that
no parts of the body are in the closing area.
For vehicles with Intelligent key: The key can
also be used to carry out the following functions
simultaneously:
•Lock the vehicle
•Close the side windows The driver’s door and the door at which the
handle is used must both be closed. The key
must be outside the vehicle. The gap between
the key and the corresponding door handle
should not be greater than 1 m.
Press and hold the
button until the side
windows are fully closed.
To interrupt convenience closing: release the
button.
You can also use the keyless locking feature to
activate convenience closing: Touch recessed sensor surface
1on the door
handle until the side windows are fully closed.
NOTE
Make sure you only touch recessed sensor sur-
face
1.
To interrupt convenience opening: release the
recessed sensor surface
1on the door handle.
Resetting the side windows
If a side window can no longer be closed fully,
you must reset it.
1. Switch the ignition switch to the ON position.
2. Close the door.
3. Pull the corresponding switch on the door control panel until the side window is com-
pletely closed
NPA1478
2-74Instruments and controls
4. Hold the switch for an additional second.
If the side window opens again slightly:
1. Immediately pull the corresponding switchon the door control panel until the side
window is completely closed.
2. Hold the switch for an additional second.
3. If the corresponding side window remains closed after the button has been released,
the side window has been reset correctly. If
this is not the case, repeat the steps above
again.
If the power window automatic function does
not operate properly after performing the pro-
cedure above, have your vehicle checked. It is
recommended you visit an INFINITI retailer for
this service.
1Close
2Open
CAUTION
•Do not place heavy objects on the glass roof
or surrounding area.
•Do not hang from the sunshade or hang any
objects from it. It may cause damage or de-
formation to the sunshade.
•Close the sunshade when you leave the ve-
hicle for extended periods of time to prevent
the inside of the vehicle from reaching high
temperatures.
SUNSHADE OPERATION
The sunshade operates only when the ignition
switch is in the ON position.
WARNING
To avoid personal injury, keep your hands, fin-
gers and head away from the sunshade arm,
the arm rail and sunshade inlet port.
NOTE
The following notes cover situations where
strong sun shining on the roof of the vehicle
causes the area around the sunshade motor to
reach high temperatures:
•If the temperature of the sunshade motor
reaches a value between 185oF (85oC) and
212oF (100oC), “restricted mode” is enabled,
and the sunshade will only be allowed to
CLOSE.
•If the temperature of the sunshade motor
exceeds 212oF (100oC), the sunshade will
not operate.
NIC2646
FIXED GLASS ROOF (IF EQUIPPED)
Instruments and controls2-75
Luggage compartment
The power outlet is used for powering electrical
accessories such as a cellular telephone.
An emergency cut-off ensures that the on-board
voltage does not drop too low. If the on board
voltage is too low, the power to the sockets is
automatically cut. This ensures that there is
sufficient power to start the engine.
CAUTION
•The outlet and plug may be hot during or
immediately after use.
•Only certain power outlets are designed for
use with a cigarette lighter unit. Do not use
any other power outlet for an accessory
lighter. It is recommended you visit an
INFINITI retailer for additional information.
•Do not use with accessories that exceed a 12
volt, 180W (15A) power draw. Do not use
double adapters or more than one electrical
accessory.
•Use this power outlet with the engine run-
ning to avoid discharging the vehicle bat-
tery.
•Avoid using when the air conditioner, head-
lights or rear window defogger is on.
•Push the plug in as far as it will go. If good
contact is not made, the plug may overheat
or the internal temperature fuse may blow.
•Before inserting or disconnecting a plug, be
sure that the electrical accessory being
used is turned OFF.
•When not in use, be sure to close the cap. Do
not allow water to contact the outlet.
WARNING
Keep the storage lids closed while driving to
help prevent injury in an accident or a sudden
stop.
NIC2684
STORAGE
Instruments and controls2-77
Adjusting
The outside rear view mirror remote control will
operate only when the ignition switch is in the
ACC or ON position.
1. Move the switch to select the left
1or right
mirror
2.
2. Adjust each mirror to the desired position using the large switch
3.
Defogging
The exterior rear view mirrors will be heated
when the rear window defogger switch is oper-
ated.
WARNING
•Objects viewed in the outside mirror on the
passenger side are closer than they appear.
Be careful when moving to the right. Using
only this mirror could cause an accident.
Use the inside mirror or glance over your
shoulder to properly judge distances to
other objects.
•Do not adjust the mirrors while driving. You
could lose control of your vehicle and cause
an accident.
Folding
Manual type (if equipped):
Fold the outside rear-view mirror by pushing it
towards the rear of the vehicle. Remote control type (if equipped)
:
The exterior rear view mirror remote control
operates when the ignition switch is in the ACC
or ON position.
Briefly press button
1. Both exterior mirrors
fold in or out.
Power folding outside mirrors (if so
equipped)
CAUTION
•Do not touch the mirrors while they are mov-
ing. Your hand may be pinched, and the
mirror may malfunction.
•Do not drive with the mirrors stored. You will
be unable to see behind the vehicle.
The exterior rear-view mirrors automatically un-
fold when the ignition is switched on or when
the vehicle doors are unlocked. Use the [Fold
Mirrors in when Locking] option under the [CON-
VENIENCE] menu of the Vehicle Information
Display to specify that the mirrors are to be
automatically folded and unfolded. The Auto
fold feature can also be switched off. See
Switching the [Fold Mirrors in when Locking]
function on/off in the2. Instruments and
controls section.
NIC2636NIC2638
3-18Pre-driving checks and adjustments
•The RearView Monitor is a convenience fea-
ture but it is not a substitute for proper
backing up. Always turn and look out the
windows, and check mirrors to be sure that
it is safe to move before operating the ve-
hicle. Always back up slowly.
•The system is designed as an aid to the
driver in showing large stationary objects
directly behind the vehicle, to help avoid
damaging the vehicle.
•The distance guide line and the vehicle
width line should be used as a reference
only when the vehicle is on a level paved
surface. The distance viewed on the monitor
is for reference only and may be different
than the actual distance between the ve-
hicle and displayed objects.
CAUTION
Do not scratch the camera lens when cleaning
dirt or snow from the lens.
The RearView Monitor system automatically
shows a rear view of the vehicle when the shift
lever is placed in the R (Reverse) position.
The radio can still be heard while the RearView
Monitor is active. To display the rear view, the RearView Monitor
system uses a camera located just above the
vehicle’s rear license plate
1.
REARVIEW MONITOR SYSTEM
OPERATION
With the ignition switch in the ON position,
move the shift lever to the R (Reverse) position
to operate the RearView Monitor.
HOW TO READ THE DISPLAYED LINES
Guiding lines which indicate the vehicle width
and distances to objects with reference to the
bumper line
Aare displayed on the monitor.
Distance guide lines:
Indicate distances from the bumper.
•Red line1: approx. 1.5 ft (0.5 m)
•Yellow line2: approx. 3 ft (1 m)
•Green line3: approx. 7 ft (2 m)
•Green line4: approx. 10 ft (3 m)
Vehicle width guide lines
5:
Indicate the approximate vehicle width when
backing up.
NAA1642SAA1896Z
Display screen, heater and air conditioner, and audio system4-17
not show objects close to the bumper or on
the ground.
•Objects viewed in the RearView Monitor dif-
fer from actual distance because a wide-
angle lens is used.
•Objects in the RearView Monitor will appear
visually opposite than when viewed in the
rear view and outside mirrors.
•Use the displayed lines as a reference. The
lines are highly affected by the number of
occupants, fuel level, vehicle position, road
conditions and road grade.
•Make sure that the lift gate is securely
closed when backing up.
•Do not put anything on the rear view cam-
era. The rear view camera is installed above
the license plate.
•When washing the vehicle with high-
pressure water, be sure not to spray it
around the camera. Otherwise, water may
enter the camera unit causing water con-
densation on the lens, a malfunction, fire or
an electric shock.
•Do not strike the camera. It is a precision
instrument. Otherwise, it may malfunctionor cause damage resulting in a fire or an
electric shock.
The following are operating limitations and do
not represent a system malfunction:
•When the temperature is extremely high or
low, the screen may not clearly display ob-
jects.
•When strong light shines directly on to the
camera, objects may not be displayed
clearly.
•Vertical lines may be seen in objects on the
screen. This is due to strong reflected light
from the bumper.
•The screen may flicker under fluorescent
light.
•The colors of objects on the RearView Moni-
tor may differ somewhat from the actual
color of objects.
•Objects on the monitor may not be clear in a
dark environment.
•Do not use wax on the camera window. Wipe
off any wax with a clean cloth dampened
with mild detergent diluted with water.
SYSTEM MAINTENANCE
CAUTION
•Do not use alcohol, benzine or thinner to
clean the camera. This will cause discolou-
ration. To clean the camera, wipe with a
cloth dampened with diluted mild cleaning
agent and then wipe with a dry cloth.
•Do not damage the camera as the monitor
screen may be adversely affected.
If dirt, rain or snow accumulates on the camera
1, the RearView Monitor may not display
objects clearly. Clean the camera by wiping it
with a cloth dampened with a diluted mild
cleaning agent and then wiping it with a dry
cloth.
NAA1688
Display screen, heater and air conditioner, and audio system4-23
4. Touch [Moving Object Detection].
5. Turn the MOD system on/off.
MOD SYSTEM LIMITATIONS
WARNING
Listed below are the system limitations for
MOD. Failure to operate the vehicle in accor-
dance with these system limitations could re-
sult in serious injury or death.
•Do not use the MOD system when towing a
trailer (if available). The system may not
function properly.
•Excessive noise (for example, audio system
volume or open vehicle window) will inter-
fere with the chime sound, and it may not be
heard.
•The MOD system performance will be lim-
ited according to environmental conditions
and surrounding objects such as:– When there is low contrast between
background and the moving objects.
– When there is blinking source of light.
– When strong light such as another vehi-
cle’s headlight or sunlight is present.
– When camera orientation is not in its
usual position, such as when mirror is
folded. –
When there is dirt, water drops or snow
on the camera lens.
– When the position of the moving objects
in the display is not changed.
•The MOD system might detect something
like flowing water droplets on the camera
lens, white smoke from the muffler, moving
shadows, etc.
•The MOD system may not function properly
depending on the speed, direction, distance
or shape of the moving objects.
•If your vehicle sustains damage to the parts
where the camera is installed, leaving it
misaligned or bent, the sensing zone may
be altered and the MOD system may not
detect objects properly.
•When the temperature is extremely high or
low, the screen may not display objects
clearly. This is not a malfunction.
MOD MALFUNCTION
If the orange MOD icon is displayed in the view,
the system is not functioning properly. This will
not hinder normal driving operation, but the
system should be inspected. It is recommended
you visit an INFINITI retailer for this service.
SYSTEM MAINTENANCE
CAUTION
•Do not use alcohol, benzine or thinner to
clean the cameras. This will cause discolor-
ation. To clean the cameras, wipe with a
cloth dampened with diluted mild cleaning
agent and then wipe with a dry cloth.
•Do not damage the cameras as the monitor
screen may be adversely affected.
If dirt, rain or snow accumulates on any of the
cameras
1, the MOD system may not operate
properly. Clean the cameras by wiping with a
cloth dampened with a diluted mild cleaning
agent and then wiping with a dry cloth.
NAA1689
4-40Display screen, heater and air conditioner, and audio system