2017 INFINITI QX30 warning

PRECAUTIONS ON CHILD RESTRAINTS
WARNING
•Failure to follow the warnings and instruc-
tions for proper use and installation of child
restraints could result in serious injury or
death of a child or other passengers in a
sudden stop or collision:– The child restraint must be used and in-
stalled properly. Always follow all of the
child restraint manufacturer’s instruc-
tions for installation and use.
– Infants and children should never be
held on anyone’s lap. Even the strongest
adult cannot resist the forces of a colli-
sion.
– Do not put a seat belt around both a child
and another passenger. –
INFINITI recommends that all child re-
straints be installed in the rear seat.
Studies show that children are safer
when properly restrained in the rear seat
than in the front seat. If you must install
a forward-facing child restraint in the
front seat, see Forward-facing child re-
straint installation using the seat belts
in the 1. Safety — seats, seat belts and
supplemental restraint system section.
– Even with the INFINITI Advanced Air bag
System, never install a rear-facing child
restraint in the front seat. An inflating air
bag could seriously injure or kill a child.
A rear-facing child restraint must only be
used in the rear seat. –
Be sure to purchase a child restraint that
will fit the child and vehicle. Some child
restraints may not fit properly in your
vehicle.
– Child restraint anchorages are designed
to withstand only those loads imposed
by correctly fitted child restraints. Under
no circumstances are they to be used to
attach adult seat belts, or other items or
equipment to the vehicle. Doing so could
damage the child restraint anchorages.
The child restraint will not be properly
installed using the damaged anchor-
ages, and a child could be seriously in-
jured or killed in a collision.
– Never use the anchor points for adult
seat belts or harnesses.
– A child restraint with a top tether strap
should not be used in the front passen-
ger seat.
– Keep seatbacks as upright as possible
after fitting the child restraint.
– Infants and children should always be
placed in an appropriate child restraint
while in the vehicle.
– When the child restraint is not in use,
keep it secured with the LATCH system or
a seat belt. In a sudden stop or collision,
loose objects can injure occupants or
damage the vehicle.
SSS0099ZWRS0256Z
CHILD RESTRAINTS
1-20Safety — seats, seat belts and supplemental restraint system

CAUTION
Remember that a child restraint left in a closed
vehicle can become very hot. Check the seat-
ing surface and buckles before placing your
child in a child restraint.
This vehicle is equipped with a universal child
restraint anchor system, referred to as the
LATCH (Lower Anchors and Tethers for CHildren)
system. Some child restraints include rigid or
webbing-mounted attachments that can be con-
nected to these anchors.
For details, see LATCH (Lower Anchors and
Tethers for CHildren) system in the1. Safety —
seats, seat belts and supplemental restraint
system section.
If you do not have a LATCH compatible child
restraint, the vehicle seat belts can be used.
Several manufacturers offer child restraints for
infants and small children of various sizes.
When selecting any child restraint, keep the
following points in mind:
•Choose only a restraint with a label certifying
that it complies with Federal Motor Vehicle
Safety Standard 213 or Canadian Motor Ve-
hicle Safety Standard 213.
•Check the child restraint in your vehicle to be
sure it is compatible with the vehicle’s seat
and seat belt system.
•If the child restraint is compatible with your
vehicle, place your child in the child restraint
and check the various adjustments to be
sure the child restraint is compatible with
your child. Choose a child restraint that is
designed for your child’s height and weight.
Always follow all recommended procedures.
•If the combined weight of the child and child
restraint is less than 65 lb (29.5 kg), you may
use either the LATCH anchors or the seat belt
to install the child restraint (not both at the
same time).
•If the combined weight of the child and child
restraint is greater than 65 lb (29.5 kg), use
the vehicle’s seat belt (not the lower an-
chors) to install the child restraint.
•Be sure to follow the child restraint manufac-
turer’s instructions for installation.
NOTE
All U.S. states and Canadian provinces or territo-
ries require that infants and small children be
restrained in an approved child restraint at all
times while the vehicle is being operated. Cana-
dian law requires the top tether strap on front- facing child restraints to be secured to the des-
ignated anchor point on the vehicle.
LATCH (Lower Anchors and Tethers
for CHildren) system
Your vehicle is equipped with special anchor
points that are used with LATCH system com-
patible child restraints. This system may also
be referred to as the ISOFIX or ISOFIX compat-
ible system. With this system, you do not have
to use a vehicle seat belt to secure the child
restraint unless the combined weight of the
child and child restraint exceeds 65 lb (29.5 kg).
If the combined weight of the child and child
restraint is greater than 65 lb (29.5 kg), use the
vehicle’s seat belt (not the lower anchors) to
install the child restraint. Be sure to follow the
child restraint manufacturer’s instructions for
installation.
The LATCH anchor points are provided to install
child restraints in the rear outboard seating
positions only.
LATCH lower anchor
WARNING
Failure to follow the warnings and instructions
for proper use and installation of child re-
straints could result in serious injury or death
Safety — seats, seat belts and supplemental restraint system1-21

Top tether anchor
WARNING
•Child restraint anchorages are designed to
withstand only those loads imposed by cor-
rectly fitted child restraints. Under no cir-
cumstances are they to be used to attach
adult seat belts, or other items or equip-
ment to the vehicle. Doing so could damage
the child restraint anchorages. The child re-
straint will not be properly installed using
the damaged anchorage, and a child could
be seriously injured or killed in a collision.
•If the cargo cover (if so equipped) contacts
the top tether strap when it is attached to
the top tether anchor, remove the cargo
cover from the vehicle or secure it on thecargo floor below its attachment location. If
the cargo cover is not removed, it may dam-
age the top tether strap during a collision. A
child could be seriously injured or killed in a
collision if the top tether strap is damaged.
•Do not allow cargo to contact the top tether
strap when it is attached to the top tether
anchor. Properly secure the cargo so it does
not contact the top tether strap. Cargo that
is not properly secured or cargo that con-
tacts the top tether strap may damage it
during a collision. A child could be seriously
injured or killed in a collision if the top
tether strap is damaged.
Top tether anchor point locations
:
1Top tether straps
2Anchor points
If you have any questions when installing a top
tether strap, it is recommended that you visit an
INFINITI retailer for this service.
REAR-FACING CHILD RESTRAINT
INSTALLATION USING LATCH
For additional information, refer to all Warnings
and Cautions in the Child safetyin the
1. Safety — seats, seat belts and supplemental
restraint system section andChild restraints
in the 1. Safety — seats, seat belts and supple-
mental restraint system section before install-
ing a child restraint. Do not use the lower
anchors if the combined weight of the child and
SSS0644ZLATCH rigid-mounted attachmentNIC2849
Safety — seats, seat belts and supplemental restraint system1-23

4. After attaching the child restraint, test itbefore you place the child in it. Push it from
side to side while holding the child restraint
near the LATCH attachment path. The child
restraint should not move more than 1 inch
(25 mm), from side to side. Try to tug it
forward and check to see if the LATCH
attachment holds the restraint in place. If
the restraint is not secure, tighten the LATCH
attachment as necessary, or put the re-
straint in another seat and test it again. You
may need to try a different child restraint or
try installing by using the vehicle seat belt (if
applicable). Not all child restraints fit in all
types of vehicles. 5. Check to make sure the child restraint is
properly secured prior to each use. If the
child restraint is loose, repeat steps 2
through 4.
REAR-FACING CHILD RESTRAINT
INSTALLATION USING THE SEAT BELTS
WARNING
The three-point seat belt with Automatic Lock-
ing Retractor (ALR) must be used when install-
ing a child restraint. Failure to use the ALR
mode will result in the child restraint not being
properly secured. The restraint could tip over
or be loose and cause injury to a child in a
sudden stop or collision.
Rear-facing child restraints must not be used
on the front seats. For additional information, refer to all Warnings
and Cautions in the
Child safetyin the
1. Safety — seats, seat belts and supplemental
restraint system section andChild restraints
in the 1. Safety — seats, seat belts and supple-
mental restraint system section before install-
ing a child restraint.
Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lb (29.5 kg). If the combined weight
of the child and the child restraint is greater
than 65 lb (29.5 kg), use the vehicle seat belt
(not the lower anchors) to install the child
restraint. Be sure to follow the child restraint
manufacturer’s instructions for installation.
Follow these steps to install a rear-facing child
restraint using the vehicle seat belts in the rear
seats:
LRS0673ZRear-facing — step 3LRS0674ZRear-facing — step 4
Safety — seats, seat belts and supplemental restraint system1-25

7. Check to make sure that the child restraint isproperly secured prior to each use. If the
seat belt is not locked, repeat steps 1
through 6.
After the child restraint is removed and the
seat belt fully retracted, the ALR mode (child
restraint mode) is canceled.
FORWARD-FACING CHILD RESTRAINT
INSTALLATION USING LATCH
For additional information, refer to all Warnings
and Cautions in the Child safetyin the
1. Safety — seats, seat belts and supplemental
restraint system section andChild restraints
in the 1. Safety — seats, seat belts and supple-
mental restraint system section before install-
ing a child restraint.
Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lb (29.5 kg). If the combined weight
of the child and the child restraint is greater
than 65 lb (29.5 kg), use the vehicle seat belt
(not the lower anchors) to install the child
restraint. Be sure to follow the child restraint
manufacturer’s instructions for installation.
Follow these steps to install a forward-facing
child restraint in the rear seats using the LATCH
system: 1. Position the child restraint on the seat. Al-
ways follow the child restraint manufactur-
er’s instructions.
2. Secure the child restraint anchor attach-ments to the LATCH lower anchors. Check to
make sure the LATCH attachment is properly
attached to the lower anchors.
If the child restraint is equipped with a top
tether strap, route the top tether strap and
secure the tether strap to the tether anchor
point. For additional information, refer to
Installing top tether strap in the1. Safety
— seats, seat belts and supplemental re-
straint system section.
Do not install child restraints that require
the use of a top tether strap in seating
positions that do not have a top tether
anchor.
3. The back of the child restraint should be secured against the vehicle seatback.SSS0645ZForward-facing web-mounted — step 2
1-28Safety — seats, seat belts and supplemental restraint system

Installing top tether strap
The child restraint top tether strap must be
used when installing the child restraint with the
LATCH lower anchor attachments. First, secure
the child restraint with the LATCH lower anchors
(rear outboard seating positions only).
WARNING
Child restraint anchorages are designed to
withstand only those loads imposed by cor-
rectly fitted child restraints. Under no circum-
stances are they to be used to attach adult seat
belts, or other items or equipment to the ve-
hicle. Doing so could damage the child re-
straint anchorages. The child restraint will not
be properly installed using the damaged an-
chorage, and a child could be seriously injured
or killed in a collision.
Outboard seating positions with removable
head restraints/headrests
:
1. If necessary, raise or remove the head restraint/headrest and store it in a secure
place. Be sure to reinstall the head restraint/
headrest when the child restraint is re- moved. For additional information about
head restraint/headrest adjustment, removal
and installation, refer to
Head
restraints/Headrests in the1. Safety —
seats, seat belts and supplemental restraint
system section.
2. Position the top tether strap
1over the
seatback.
3. Secure the tether strap to the tether anchor point
2on the seatback behind the child
restraint.
4. Tighten the tether strap according to the manufacturer’s instructions to remove any
slack.
Outboard seating positions with fixed head
restraints/headrests
:
1. If the child restraint has a single tether strap, route the strap
1over the top of the outer
head restraint/headrest. If the child restraint
has two tether straps, route them round each
side of the outer head restraint/headrest.
2. Secure the tether strap to the tether anchor point
2on the seatback behind the child
restraint.
3. Tighten the tether strap according to the manufacturer’s instructions to remove any
slack.
NIC2849
1-30Safety — seats, seat belts and supplemental restraint system

If you have any questions when installing a
top tether strap, it is recommended that you
visit an INFINITI retailer for this service.
FORWARD-FACING CHILD RESTRAINT
INSTALLATION USING THE SEAT BELTS
WARNING
The three-point seat belt with Automatic Lock-
ing Retractor (ALR) must be used when install-
ing a child restraint. Failure to use the ALR
mode will result in the child restraint not being
properly secured. The restraint could tip over
or be loose and cause injury to a child in a
sudden stop or collision. Also, it can change
the operation of the front passenger air bag.
For additional information, refer toFront pas-
senger air bag and status light in the1. Safety
— seats, seat belts and supplemental restraint
system section.
For additional information, refer to all Warnings
and Cautions in the Child safetyin the
1. Safety — seats, seat belts and supplemental
restraint system section andChild restraints
in the 1. Safety — seats, seat belts and supple-
mental restraint system section before install-
ing a child restraint. Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lb (29.5 kg). If the combined weight
of the child and the child restraint is greater
than 65 lb (29.5 kg), use the vehicle seat belt
(not the lower anchors) to install the child
restraint. Be sure to follow the child restraint
manufacturer’s instructions for installation.
Follow these steps to install a forward-facing
child restraint using the vehicle seat belt in the
rear seats or in the front passenger seat:
1.If you must install a child restraint in the front
seat, it should be placed in a forward-facing
direction only. Move the seat to the rearmost
position. Child restraints for infants must be
used in the rear-facing direction and, there-
fore, must not be used in the front seat.
2. Position the child restraint on the seat. Always follow the child restraint manufactur-
er’s instructions. The back of the child re-
straint should be secured against the vehicle
seatback. If necessary, adjust or remove the
head restraint/headrest to obtain the correct
child restraint fit. If the head restraint/
headrest is removed, store it in a secure
place. Be sure to reinstall the head restraint/
headrest when the child restraint is removed.
For additional information about head
restraint/headrest adjustment, removal and
WRS0699ZForward-facing (front passenger seat) — step 1
Safety — seats, seat belts and supplemental restraint system1-31

10. If the child restraint is installed in the frontpassenger seat, place the ignition switch in
the ON position. The front passenger air
bag status OFF light should illuminate. If
this light is not illuminated refer to Front
passenger air bag and status light in the
1. Safety — seats, seat belts and supple-
mental restraint system section.Move the
child restraint to another seating position.
Have the system checked. It is recom-
mended you visit an INFINITI retailer for this
service. After the child restraint is removed
and the seat belt is fully retracted, the ALR
mode (child restraint mode) is canceled.
If the indicator
lamp does NOT light continuously when a
child restraint is installed on the front passenger seat, the seat may not be used
for a child restraint. Move the child re-
straint to another position. See
Troubleshooting
later in this section. Have
the system checked. It is recommended you
visit an INFINITI retailer for this service.
Installing top tether strap
WARNING
Child restraint anchorages are designed to
withstand only those loads imposed by cor-
rectly fitted child restraints. Under no circum-
stances are they to be used to attach adult seat
belts, or other items or equipment to the ve-
hicle. Doing so could damage the child re-
straint anchorages. The child restraint will not
be properly installed using the damaged an-
chorage, and a child could be seriously injured
or killed in a collision.
The child restraint top tether strap must be
used when installing the child restraint with
seat belts.
First, secure the child restraint with the seat
belt. Outboard seating positions with removable
head restraints/headrests
:
1. If necessary raise or remove the head
restraint/headrest and store it in a secure
place. Be sure to reinstall the head restraint/
headrest when the child restraint is re-
moved. For additional information about
head restraint/headrest adjustment, removal
and installation, refer to Head
restraints/Headrests in the1. Safety —
seats, seat belts and supplemental restraint
system section.
2. Position the top tether strap
1over the
seatback.
3. Secure the tether strap to the tether anchor point
2on the seatback behind the child
restraint.
SSS0676ZForward-facing — step 10NIC2848Rear seat - Type A
1-34Safety — seats, seat belts and supplemental restraint system