2017 INFINITI QX30 display

How to change the set vehicle speed
To cancel the preset speed, use any of these
methods:
•Tap the brake pedal when the vehicle is
moving.
•Quickly push the cruise control lever in the
direction of arrow
5.
The message [ICC OFF] appears in the vehicle
information display for 5 seconds.
To reset at a higher cruising speed, use one of
the following methods:
•Depress the accelerator pedal. When the
vehicle attains the desired speed, quickly
pull the cruise control lever towards you
3.
•Pull the cruise control lever up1beyond
the pressure point. The set vehicle speed will
increase by approximately 10 MPH (10 km/h).
•Pull the cruise control lever up (1) at the
pressure point. The set vehicle speed will
increase by approximately 1 MPH (1 km/h).
To reset at a lower cruising speed, use one of
the following methods:
•Lightly tap the brake pedal. When the vehicle
attains the desired speed, quickly pull the
cruise control lever towards you
3.
•Pull the cruise control lever down4beyond
the pressure point. The set vehicle speed will
decrease by approximately 10 MPH (10 km/
h).
•Pull the cruise control lever down4to the
pressure point. The set vehicle speed will
decrease by approximately 1 MPH (1 km/h).
To resume the preset speed, quickly pull the
cruise control lever towards you
4. The vehicle
will resume the last set cruising speed when the
vehicle speed is over 20 MPH (30 km/h).
NOTE
If you do not fully release the accelerator pedal,
the [ICC Deactivated Automatically] message
appears in the vehicle information display. The
set distance to a slower-moving vehicle in front will then not be maintained. You will be driving
at the speed you determine by the position of the
accelerator pedal.
You can also activate ICC when stationary. The
lowest speed that can be set is 20 MPH
(30 km/h).
Stopping
WARNING
•To help avoid risk of injury or death through
unintended operation of the vehicle and/or
its systems, do not leave children, people
who require the assistance of others, or
pets unattended in your vehicle.
•The ICC system should only be used to keep
the vehicle stationary when the driver is
actively using the system. When parking
the vehicle, make sure to turn OFF the ICC
system, use the brake, press the PARK (P)
button, and place the ignition switch in the
LOCK position prior to exiting the vehicle.
Failure to do so could lead to serious injury
or death. The ICC system will not hold the
vehicle in place after coming to a stop when
any of the following conditions occur:
– There is a malfunction in the system or in
the voltage supply.
NSD582A
5-52Starting and driving

–The ICC system has been deactivated
with the cruise control lever, e. g. by a
vehicle occupant.
– The accelerator pedal has been de-
pressed, e.g. by a vehicle occupant.
For further information on deactivating the ICC
system, see ICC switch (cruise control lever)
earlier in this section
If the ICC system detects that the vehicle in
front is stopping, it brakes your vehicle until it
is stationary (within the braking limitations of
the system).
Once your vehicle is stationary, it remains
stationary and you do not need to depress the
brake.
NOTE
•After a short period, the vehicle is secured by
the electric parking brake, thus relieving the
service brake.
•Depending on the specified minimum dis-
tance, your vehicle will come to a standstill
at a sufficient distance behind the vehicle in
front. The specified minimum distance is set
using the control on the cruise control lever. The electric parking brake secures the vehicle
automatically if the ICC system is activated
when the vehicle is stationary and:
•A system fault occurs.
•The power supply is insufficient.
If a malfunction in the electric parking brake
occurs, then the transmission may also be
shifted into position P (Park) automatically.
How to change the set distance to
the vehicle ahead
The distance to the vehicle ahead can be se-
lected at any time depending on the traffic
conditions.
To increase the distance to the vehicle ahead,
turn the knob
3toward the rear2. To de-
crease the distance to the vehicle ahead, turn
the knob
3toward the front1.
You can see this distance in the vehicle infor-
mation display.
The distance to the vehicle ahead will change
according to the vehicle speed. The higher the
vehicle speed, the longer the distance.
NSD583A
Starting and driving5-53

Approach warning
If your vehicle comes closer to the vehicle
ahead due to rapid deceleration of that vehicle
or if another vehicle cuts in, the system warns
the driver with the chime and distance warning
light. Decelerate by depressing the brake pedal
to maintain a safe vehicle distance if:
•The chime sounds.
•The distance warning light is illuminated.
The warning chime may not sound and the
distance warning light may not illuminate in
some cases when there is a short distance
between vehicles. Some examples are:
•When the vehicles are traveling at the same
speed and the distance between vehicles is
not changing. In this case, the distance
warning light will be on.
•When the vehicle ahead is traveling faster
and the distance between vehicles is increas-
ing.
•When a vehicle cuts in near your vehicle
•The warning chime will not sound and the
distance warning light will not illuminate
when: – The vehicle approaches other vehicles that are parked or moving slowly. – The accelerator pedal is depressed, over-
riding the system.
Also, the sensor sensitivity can be affected by
vehicle operation (steering maneuver or driving
position in the lane) or traffic or vehicle condi-
tion (for example, if a vehicle is being driven
with some damage).
Automatic cancellation
A chime sounds and the message [ICC off] is
displayed in the vehicle information display for
5 seconds under the following conditions and
the control is automatically canceled.
•The electric parking brake is applied.
•The VDC intervenes or the VDC is deacti-
vated.
•The P (Park), R (Reverse) or N (Neutral)
position is engaged.
•The cruise control lever is pulled in order to
pull away but the front passenger door or
one of the rear doors is open.
•The vehicle is skidding or a wheel slips.
•Active Park Assist is activated.
ICC LIMITATIONS
WARNING
Listed below are the system limitations for the
ICC system. Failure to operate the vehicle in
accordance with these system limitations
could result in serious injury or death.
•This system is only an aid to assist the
driver and is not a collision warning or
avoidance device. It is the driver’s responsi-
bility to stay alert, drive safely and be in
control of the vehicle at all times.
•The system is primarily intended for use on
straight, dry, open roads with light traffic. It
is not advisable to use the system in city
traffic or congested areas.
•This system will not adapt automatically to
road conditions. This system should be
used in evenly flowing traffic. Do not use the
system on roads with sharp curves, or on icy
roads, in heavy rain or in fog.
•As there is a performance limit to the dis-
tance control function, never rely solely on
the ICC system. This system does not cor-
rect careless, inattentive or absent-minded
driving, or overcome poor visibility in rain,
fog, or other bad weather. Decelerate the
vehicle speed by depressing the brake
5-54Starting and driving

Crossing vehicles
The ICC system may detect vehicles that are
crossing your lane by mistake. Activating the
ICC system at traffic lights with crossing traffic,
for example, could cause your vehicle to pull
away unintentionally.
1Steering wheel mounted controls (left
side)
2Vehicle information display
ADisplay area
BMENU bar
NSD608
NSD626
5-58Starting and driving

SYSTEM TEMPORARILY UNAVAILABLE
When the radar sensor area is covered with dirt
or is obstructed, the system will automatically
be canceled. If the radar sensor area is covered
with ice, a transparent or translucent vinyl bag,
etc., the ICC system may not detect them. In
these instances, the ICC system may not cancel
and may not be able to maintain the selected
following distance from the vehicle ahead.
If the ICC system stops working due to a
malfunction or some other reason, one of the
following messages will be displayed in the
vehicle information display
2.
•[ICC off]
•[ICC Now Available]
•[ICC Currently Unavailable See Operator’s
Manual]
•[ICC Inoperative]
•[ICC Suspended]
•[ICC–––MPH]
[ICC off]: The ICC system has been deactivated.
If it was not deactivated by the driver, a warning
tone also sounds. [ICC Now Available]:
The ICC system is opera-
tional again after having been temporarily un-
available. You can now reactivate the ICC sys-
tem.
[ICC Currently Unavailable See Operator’s
Manual]: The ICC system is temporarily inopera-
tive. Possible causes:
•The function is impaired due to heavy rain or
snow.
•The radar sensor system is temporarily inop-
erative, e. g. due to electromagnetic radia-
tion emitted by nearby TV or radio stations or
other sources of electromagnetic radiation.
•The system is outside the operating tempera-
ture range.
•The on-board voltage is too low.
A warning tone also sounds.
Once the causes listed above no longer apply,
the display message goes out.
If the display message does not disappear:
•Pull over and stop the vehicle safely as soon
as possible, paying attention to road and
traffic conditions.
•Secure the vehicle against rolling away.
•Restart the engine. [ICC Inoperative]:
The ICC system is malfunc-
tioning. The adaptive brake assist function may
also have failed. A warning tone also sounds.
Have the system checked. It is recommended
you visit an INFINITI retailer for this service.
[ICC Suspended]: You have depressed the accel-
erator pedal. The ICC system is no longer
controlling the speed of the vehicle.
The display message should disappear when
you remove your foot from the accelerator pedal
[ICC–––MPH]: An activation condition for the
ICC system is not fulfilled.
Check the activation conditions for the ICC
system.
Starting and driving5-59

The FEB system uses a radar sensorAlocated
behind the INFINITI logo to measure the dis-
tance to the vehicle ahead in the traveling lane.
FEB SYSTEM OPERATION
1Steering wheel mounted controls (left
side)
2Distance warning light
3Forward emergency braking OFF display
NSD645
NSD624
Starting and driving5-61

The FEB system consists of a distance warning
function with an autonomous emergency brak-
ing function and adaptive brake assist function.
The FEB system can help you to minimize the
risk of a collision with the vehicle in front or
reduce the effects of such a collision
If the FEB system detects that there is a risk of
a collision, you will be warned visually and
audibly. If you do not react to the visual and
audible collision warning, autonomous braking
can be initiated in critical situations. If you
apply the brake yourself in a critical situation,
the adaptive brake assist function assists you.
Distance warning function
The distance warning function can help you to
minimize the risk of a collision with the vehicle
in front or reduce the effects of such a collision.
If the distance warning function detects that
there is a risk of a collision, you will be warned
visually and audibly.
The distance warning function issues a warning
at speeds:
•Of approximately 20 MPH (30 km/h) or more,
if, over several seconds the distance main-
tained to the vehicle traveling in front is
insufficient. The distance warning light then
lights up in the combination meter.
•Of approximately 4 MPH (7 km/h) or more, if
you rapidly approach a vehicle in front. An
intermittent warning tone will then sound
and the distance warning light will light up in
the combination meter.
If a warning is issued:
•Brake immediately in order to increase the
distance from the vehicle in front.
or
•Take evasive action provided it is safe to do
so.
WARNING
Due to the nature of the system, particularly
complicated but non-critical driving conditions
may also cause the system to display a
warning.
Up to a speed of approximately 45 MPH (70
km/h), the distance warning function can also
react to stationary (stopped or parked) vehicles.
If you approach a stationary vehicle and the
distance warning function detects a risk of a
collision, the system will alert you both visually
and acoustically.
NSD598Distance warning light
5-62Starting and driving

TURNING THE FEB SYSTEM ON/OFF
1Steering-wheel mounted controls (left
side)
2Vehicle information display
ADisplay area
BMenu barUse the following procedure to turn the FEB
system on or off:
1. Press the
button on the
steering wheel
1to select the [DriveAssist]
menu on the Menu bar
B. 2. Press the
orbutton to select
[Emergency Brake].
3. Press the button on the steering wheel
1. The current selection is displayed.
4. To activate/deactivate the FEB system: press the button again
When the FEB system is deactivated, the
symbolCappears in the vehicle information
display.
NOTE
The FEB system will be automatically turned on
when the engine is restarted.
NSD626
NSD630
5-64Starting and driving