2017 INFINITI QX30 Button

3. Turn the key to the START position3in the
ignition lock and release it as soon as the
engine is running.
If the engine is very hard to start because it is
flooded, depress the accelerator pedal all the
way to the floor and hold it. Turn the ignition
switch to the START position to start cranking
the engine. After 5 or 6 seconds, stop cranking
by turning the ignition switch to OFF. After
cranking the engine, release the accelerator
pedal. Crank the engine with your foot off the
accelerator pedal by depressing the brake
pedal and turning the ignition switch to start
the engine. If the engine starts, but fails to run,
repeat the above procedure.CAUTION
Do not operate the starter for more than 15
seconds at a time. If the engine does not start,
turn the ignition key to the OFF position and
wait 10 seconds before cranking again, other-
wise the starter could be damaged.
4. Warm-up
Allow the engine to idle for at least 30
seconds after starting. Do not race the en-
gine while warming it up. Drive at moderate
speed for a short distance first, especially in
cold weather. In cold weather, keep the
engine running for a minimum of2-3
minutes before shutting it off. Starting and
stopping the engine over a short period of
time may make the vehicle more difficult to
start.
5. To stop the engine, Shift the transmission to position P (Park) by pressing the

button.
and turn the ignition switch to the OFF
position. NOTE
Care should be taken to avoid situations that can
lead to potential battery discharge and potential
no-start conditions such as:
•Installation or extended use of electronic
accessories that consume battery power
when the engine is not running (Phone char-
gers, GPS, DVD players, etc.)
•Vehicle is not driven regularly and/or only
driven short distances. In these cases, the
battery may need to be charged to maintain
battery health.
Starting and driving5-17

Transmission position display:
NOTE
If the transmission position display in the ve-
hicle information display is not working, you
should pull away carefully to check whether the
desired transmission position IS engaged. Ide-
ally, you should select transmission position D
and automatic drive program E or S.
The shift lever indicator
1located in the lower
part of the vehicle information display shows
the current position of the transmission.
It shows the P,R,N,D modes when the transmis-
sion is in auto mode or the shift position when
the transmission is in manual mode.
WARNING
Apply the parking brake if the shift lever is in
any position while the engine is not running.
Failure to do so could cause the vehicle to move
unexpectedly or roll away and result in serious
personal injury or property damage.
CAUTION
Use the P (Park) or R (Reverse) position only
when the vehicle is completely stopped. P (Park)
:
CAUTION
To prevent transmission damage, use the P
(Park) position only when the vehicle is com-
pletely stopped.
Use this position when the vehicle is parked or
when starting the engine. Always make sure
that the vehicle is completely stopped before
pressing button
1to engage the P (Park)
position. For maximum safety, the brake pedal
must be depressed before engaging the P (Park)
position. Use this position together with the
parking brake. When parking on a hill, first
depress the brake pedal, apply the parking
brake and then engage the P (Park) position.
The parking lock should not be used as a brake
when parking. In order to secure the vehicle,
NSD649NSD586
Starting and driving5-19

always apply the electric parking brake in addi-
tion to the parking lock.
In the event of a malfunction of the vehicle’s
electronics, the transmission may lock in posi-
tion P (Park). Have the vehicle electronics
checked immediately. It is recommended you
visit an INFINITI retailer for this service.
Park position P is automatically engaged if:
•You switch off the engine using the key and
remove the key.
•You open the driver’s door when the vehicle
is stationary or driving at very low speed and
the transmission is in position D (Drive) or R
(Reverse).
R (Reverse)
:
CAUTION
To prevent transmission damage, use the R
(Reverse) position only when the vehicle is
completely stopped.
Use this position to back up the vehicle.
Make sure the vehicle is completely stopped
before selecting the R (Reverse) position. The
brake pedal must be depressed and the shift
lever button pushed in to move the shift lever from P (Park), N (Neutral) or any drive position to
R (Reverse).
N (Neutral)
:
Neither forward nor reverse gear is engaged.
The engine can be started in this position. You
may shift to N (Neutral) and restart a stalled
engine while driving the vehicle.
D (Drive)
:
Use this position for all normal forward driving.
The automatic transmission changes gear auto-
matically. All forward gears are available.
Changing gear
The automatic transmission shifts to the indi-
vidual gears automatically when it is in trans-
mission position D (Drive). Shifting is deter-
mined by:
•The selected drive program.
•The position of the accelerator pedal.
•The road speed.
Accelerator pedal position
:
Your style of driving influences how the auto-
matic transmission shifts gear:
•little throttle: early upshifts
•more throttle: late upshifts
Holding the vehicle stationary on
uphill gradients
WARNING
If the transmission overheats, the electronic
management system is automatically deacti-
vated. This interrupts the power transmission
from the engine to the wheels. The vehicle
may, for example, roll backwards on gradients.
There is a risk of an accident. Never hold the
vehicle stationary on uphill gradients by de-
pressing the accelerator.
The transmission may overheat if you hold the
vehicle stationary on uphill gradients by de-
pressing the accelerator pedal. If the transmis-
sion overheats, a warning tone sounds and the
[Stop Vehicle Shift to P Leave Engine Running]
display message appears in the vehicle infor-
mation display. You will only be able to con-
tinue your journey once the transmission has
cooled down and the display message in the
vehicle information display has disappeared.
5-20Starting and driving

The Idle Stop/Start function switches the en-
gine off automatically if the vehicle is stopped
under certain conditions.
When pulling away again, the engine starts
automatically. The Idle Stop/Start function
thereby helps you to reduce the fuel consump-
tion and emissions of your vehicle.
WARNING
If the engine is switched off automatically and
you exit the vehicle, the engine is restarted
automatically. The vehicle may begin moving
There is a risk of accident and injury.
If you wish to exit the vehicle, always turn off
the ignition and secure the vehicle against roll-
ing away.If the
Idle Stop/Start symbol is shown in
green in the vehicle information display, the
Idle Stop/Start function switches the engine off
automatically once the vehicle stops moving.
The Idle Stop/Start function is automatically
activated each time you start the engine with
the ignition key.
If the Idle Stop/Start function has been manu-
ally deactivated (see Deactivating/activating
the Idle Stop/Start function later in this sec-
tion) or a malfunction has caused the system to
be deactivated, the
Idle Stop/Start sym-
bol is not displayed.
AUTOMATIC ENGINE SWITCH-OFF
The Idle Stop/Start function is operational and
theIdle Stop/Start symbol is displayed
in green in the vehicle information display, if:
•The indicator lamp in the ECO button is lit
green.
•The outside temperature is within the range
that is suitable for the system.
•The engine is at normal operating tempera-
ture.
•The set temperature for the vehicle interior
has been reached.
•The battery is sufficiently charged.
•The system detects that the windshield is not
misted up when the air-conditioning system
is switched on.
•The hood is closed.
•The driver’s door is closed and the driver’s
seat belt is fastened.
If the conditions for automatic engine switch-off
are not all fulfilled, the
Idle Stop/Start
symbol is shown in yellow.
All of the vehicle’s systems remain active when
the engine is switched off automatically.
NSD620Idle Stop/Start symbol
IDLE STOP/START SYSTEM (IF EQUIPPED)
Starting and driving5-27

The engine can be switched off automatically a
maximum of four times (initial stop, then three
subsequent stops) in succession. The
Idle Stop/Start symbol is shown in yellow in the
vehicle information display after the engine has
been started automatically for the fourth time.
When the
Idle Stop/Start symbol is
shown in green in the vehicle information dis-
play, automatic engine switch-off is again pos-
sible.
NOTE
If the hood is opened while the engine is running
and the Idle Stop/Start function is operational,
the engine will switch off automatically.
If the vehicle is brought to a standstill in D or N,
the Idle Stop/Start function switches off the
engine automatically.
AUTOMATIC ENGINE START
The engine is started automatically if:
•You switch off the Idle Stop/Start function by
pressing the ECO button.
•You engage Reverse R or Drive D.
•You unfasten your seat belt or open the
driver’s door.
•The vehicle starts to roll.
•The brake system requires this.
•The temperature in the vehicle interior devi-
ates from the set range.
•The system detects moisture on the wind-
shield when the air-conditioning system is
switched on.
•The battery’s charge status is too low.
The engine is started automatically if you:
•Release the brake pedal in transmission
position D (Drive) or N (Neutral).
•Depress the accelerator pedal.
•Move the transmission out of position P
(Park).
Shifting the transmission to position P (Park)
does not start the engine.
If you shift the transmission from R (Reverse) to
D (Drive), the Idle Stop/Start function is avail-
able again once the
Idle Stop/Start
symbol reappears in green in the vehicle infor-
mation display.
DEACTIVATING/ACTIVATING THE IDLE
STOP/START FUNCTION
•To deactivate: press ECO button1. Indicator
lamp
2and theIdle Stop/Start
symbol in the vehicle information display
turn off.
•To activate: press ECO button1. Indicator
lamp
2lights up. If all conditions for auto-
matic engine switch-off (see Automatic en-
gine switch-off earlier in this section) are
fulfilled, the
Idle Stop/Start symbol is
shown in green in the vehicle information
display.
If not all conditions for automatic engine
switch-off are met, the
Idle Stop/Start
symbol is lit yellow in the vehicle information
NIC2633
5-28Starting and driving

display. If this is the case, the Idle Stop/Start
function is not active.
If indicator lamp
2on ECO button1is off, the
Idle Stop/Start function has been deactivated
manually or as the result of a malfunction. The
engine will then not be switched off automati-
cally when the vehicle stops.
WARNING
Failure to follow the warnings and instructions
for proper use of the LDW system could result
in serious personal injury or death. The LDW
system will not steer the vehicle or prevent
loss of control. It is the driver’s responsibility
to stay alert, drive safely, keep the vehicle in
the traveling lane, and be in control of the
vehicle at all times.
The LDW system warns the driver with a warn-
ing light and intermittent steering vibration that
the vehicle is beginning to leave the traveling
lane. The LDW system uses a camera
1installed
behind the windshield to monitor the lane
markers of your traveling lane.
NSD644
LANE DEPARTURE WARNING (LDW)
SYSTEM (IF EQUIPPED)
Starting and driving5-29

HOW TO ENABLE/DISABLE THE LDW
SYSTEM
1. Press theorbutton on the
steering wheel
1to select the [DriveAssist]
menu on the Menu bar
B.
2. Press the
orbutton to select
[Lane Departure Warning].
3. Press the button on the steering wheel
1. The current selection is displayed.
4. Press the to confirm.
5. Press the
orbutton to set [Off],
[Standard] or [Adaptive].
6. Press the button to save the setting.
When the LDW is activated, the vehicle
information display shows the lane mark- ings as bright lines in the assistance graphic
in the display area
A
When [Standard] is selected, no warning vibra-
tion occurs if:
•You have switched on the turn signals. In this
event, the warnings are suppressed for a
certain period of time.
•A driving safety system intervenes, such as
ABS, brake assist system (BAS) or VDC.
When [Adaptive] is selected, no warning vibra-
tion occurs if:
•You have switched on the turn signals. In this
case the warnings are suppressed for a
certain period of time.
•A driving system intervenes, such as ABS,
BAS or VDC.
•You accelerate forcefully.
•You brake forcefully.
•You steer actively, for example, swerve to
avoid an obstacle or change lane quickly.
•You cut the corner on a sharp bend.
The system may detect certain conditions and
warns you accordingly. The warning vibration occurs earlier if:
•You approach the outer lane marking on a
bend.
•The road has very wide lanes, for example, a
freeway.
•The system detects solid lane markings.
The warning vibration occurs later if:
•The road has narrow lanes.
•You cut across a corner on a bend.
LDW SYSTEM LIMITATIONS
WARNING
Listed below are the system limitations for the
LDW system. Failure to operate the vehicle in
accordance with these system limitations
could result in serious injury or death.
•This system is only a warning device to in-
form the driver of a potential unintended
lane departure. It will not steer the vehicle
or prevent loss of control. It is the driver’s
responsibility to stay alert, drive safely,
keep the vehicle in the traveling lane, and
be in control of the vehicle at all times.
NSD599Assistance graphic
Starting and driving5-31

1Steering wheel mounted controls
2Vehicle information display
ADisplay area
BMenu bar
LDW SYSTEM TEMPORARILY
UNAVAILABLE
Under the following conditions, the LDW system
will be canceled automatically, and the mes-
sage [Lane Departure Warning Currently Un-available See Operator’s Manual] is displayed
in the vehicle information display
2. The LDW
system is temporarily unavailable.
•The windshield is dirty in the camera’s field
of vision.
•Visibility is impaired due to heavy rain, snow
or fog.
•There have been no lane markings for an
extended period.
•The lane markings are worn, dark, or covered
by dirt or snow, etc..
Action to take: When the above conditions no
longer exist, the message goes out and the LDW
system is operational again. If the message
continues to appear, stop the vehicle in a safe
location, press the P (Park) button , and clean
the windshield.
NSD626
Starting and driving5-33