2017 Hyundai Elantra lock

7-76
Maintenance
3.Loosen the assembly retaining
nuts.
4.Remove the rear combination light
assembly from the body of the
vehicle.
Stop/Tail lamp and turn signal
lamp
5.Remove the socket from the
assembly by turning the socket
anticlockwise until the tabs on the
socket align with the slots on the
assembly.
OAD075037
OAD075038
■Ty p e A
■Ty p e B , C
Ta i l / s t o p
Tu r n s i g n a l
Tu r n s i g n a l
OAD075051OAD075050

7-77
7
Maintenance
6.Remove the bulb from the socket
by pressing it in and rotating it anti-
clockwise until the tabs on the bulb
align with the slots in the socket.
Pull the bulb out of the socket.
7.Insert a new bulb by inserting it into
the socket and rotating it until it
locks into place.
8.Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
Inside lamp
1.Open the boot.
2.Loosen the retaining screw of the
boot lid cover and then remove the
cover.
3.Disconnect the connector and then
remove the nuts by turning the nuts
anticlockwise.
Reverse lamp
1.Take the light assembly out.
OAD075056
OAD075055
OAD075052

7-78
Maintenance
2.Remove the socket from the
assembly by turning the socket
anticlockwise until the tabs on the
socket align with the slots on the
assembly.
3.Remove the bulb by pulling it out.
4.Insert a new bulb by inserting it into
the socket.
5.Install the light assembly to the
boot.
6.Reinstall the nuts and connector
and then the boot lid cover by
pushing in the screw.
Tail and rear fog lamp (if equipped)
1.Remove the socket from the
assembly by turning the socket
anticlockwise until the tabs on the
socket align with the slots on the
assembly.
2.Remove the bulb from the socket
by pressing it in and rotating it anti-
clockwise until the tabs on the bulb
align with the slots in the socket.
Pull the bulb out of the socket.
3.Insert a new bulb by inserting it into
the socket and rotating it until it
locks into place.
4.Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
OAD075069L
OAD075070L
■Ty p e A
■Ty p e B , C
Back up
Ta i lFog(if equipped)
Fog(if equipped)
Back up

7-79
7
Maintenance
High mounted stop lamp
replacement
1.Open the boot.
2.Remove the socket by turning it
anticlockwise until the tabs on the
socket align with the slots.
3.Remove the bulb from the socket
by pressing it in and rotating it anti-
clockwise until the tabs on the bulb
align with the slots in the socket.
Pull the bulb out of the socket.
4.Insert a new bulb by inserting it into
the socket and rotating it until it
locks into place.
5.Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
Licence plate light bulb
replacement
1.Remove the cover by pressing it in
the direction of the arrows.
2.Remove the bulb by pulling it
straight out.
3.Install a new bulb.
4.Reinstall in the reverse order.
OAD075043
OAD075041
OAD075042

8-10
Specifications & Consumer information
The tyres supplied on your new vehi-
cle are chosen to provide the best
performance for normal driving.
The tyre label located on the driver's
side centre pillar gives the tyre pres-
sures recommended for your vehicle.
The engine number is stamped on
the engine block as shown.A compressor label informs you of
the type of compressor your vehicle
is equipped with such as; model,
supplier part number, production
number, refrigerant (1) and refriger-
ant oil (2).
TTYYRREE SSPPEECCIIFFIICCAATTIIOONN AANNDD
PPRREESSSSUURREE LLAABBEELL
EENNGGIINNEE NNUUMMBBEERR
OAD085007ROHC081001
AAIIRR CCOONNDDIITTIIOONNEERR
CCOOMMPPRREESSSSOORR LLAABBEELL
OAD085009L