2017 Citroen BERLINGO MULTISPACE RHD light

20
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Don't forget
When  leaving   the   vehicle,   check   that  
the lighting is of

f and nothing of value
is
  visible.
As a safety precaution (with children
on
  board),   remove   the   key   from   the  
ignition when leaving the vehicle, even
for

  a   short   time.
Good practice
Do not make any modifications to the electronic  immobiliser   system.
Operating the remote control, even
when
  it   is   in   your   pocket,   may   result   in  
involuntary

  unlocking   of   the   doors.
The simultaneous use of other
high frequency equipment (mobile
telephones, domestic alarms…), may
interfere with the operation of the
remote
  control   temporarily.
The remote control does not operate
while
  the   key   is   in   the   ignition,   even   if  
the

  ignition   is   off.
ELECTRONIC
IMMOBILISER
If you lose your keys
Visit a CITROËN dealer with the
vehicle's  V5   registration   certificate   and  
your

  identification   document.
A CITROËN dealer will be able
to
  retrieve   the   key   code   and  
the transponder code so that a
replacement

  key   can   be   ordered.When purchasing a second-hand
vehicle,
  have   the   keys   memorised   by  
a CITROËN dealer

, so as to be sure
that   the   keys   in   your   possession   are  
the only ones that can be used to start
the

  vehicle.
ALARM
If fitted on your vehicle, this provides two
  types   of   protection:
-
 
exterior
  protection:   it   sounds   if   a  
front/rear

  door   or   the   bonnet   is  
opened.
-

 
interior
  protection:   it   sounds   if  
the volume inside the passenger
compartment

  changes   (breaking   of  
a window or a movement inside the
vehicle).
If

 
your
 
vehicle
 
is
 
fitted
 
with
 
a
 
separation
 
partition, the interior protection is not
active

  in   the   load   space.
Locking the vehicle with
complete alarm
Setting the alarm
- Switch off the ignition and get out of
the   vehicle.
-
 
Set
  the   alarm   within   five   minutes   of  
getting

  out   of   the   vehicle,   by   locking  
or

  deadlocking   using   the   remote  
control.

 
The
  red   LED,   located   in   the  
button,

  flashes   once   per   second.
All of the keys contain an electronic immobiliser  device.
This
  device   locks   the   engine   supply  
system.

  It   is   activated   automatically  
when

  the   key   is   removed   from   the  
ignition.
After the ignition is switched on, a
dialogue

  is   established   between   the   key  
and

  the   electronic   immobiliser   system.
The
  metal   part   of   the   key   must   be  
unfolded correctly for correct dialogue
to

  take   place.
Access

28
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Dials
1. Distance  recorder   in   kilometres   /  miles.
2.
 
Display
  screen.
3.

Fuel gauge, coolant temperature
gauge.
4.

 
Rev
  counter.
5.
 
T
rip   distance   recorder   /   service  
indicator

  reset.
6.
 
Instrument
  panel   lighting   dimmer.Level 1
INSTRUMENT PANELDisplay screens
Screens
The format of the information
presented in the screen depends on
the
  vehicle's   equipment   level.
Level 2
with the touch screen tablet

33
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Warning lamp isindicatesSolution - action
Coolant
temperature
and level on with needle
in the red
zone.
an abnormal increase in
temperature.
Park
  and   switch   off   the   ignition   then   allow   to   cool.  
V

isually   check   the   level.
flashing. a
  drop   in   the   coolant   level.Chapter
  7,   "Levels"   section.
Contact
  a   CITROËN dealer   or   a   qualified  
workshop.
Service on

  temporarily. minor   faults   or   warnings.Consult
  the   alert   log   in   the   display   or   screen.
If your vehicle is equipped with a trip computer or
a
  screen:   refer   to   the   "Steering   mounted   controls"  
section

  in   Chapter   4.
Contact
  a   CITROËN   dealer   or   a   qualified  
workshop.
remaining

  on. major   faults.
Seat belt not
fastened on then
flashing.
the
  driver   and/or   front  
passenger has not fastened
their

  seat   belt.Pull
  the   strap   then   insert   the   tongue   in   the   buckle.
accompanied
by an audible
signal then
remains
  on.the vehicle is moving with
the
  driver's   and/or   front  
passenger's seat belt not
fastened.Check

  that   the   seat   belt   is   fastened   by   pulling   the  
strap.
Chapter

  5,   "Seat   belts"   section.
ECO on.
The Stop & Start
system
has put the engine in STOP
mode following a vehicle
stop
  (red   light,   traffic   jam,  
etc...).As soon as you want to move of

f, the warning
lamp goes off and the engine restarts
automatically
  in   START
 
mode.
flashes
  for   a  
few seconds,
then

  goes   off.STOP mode is temporarily
unavailable.
or
START mode has been
invoked
  automatically.Chapter
  3,   "Stop   &   Start"   section.
READY TO GO
3

36
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Warning lamp isindicatesSolution - action
Dipped beam
headlamps
/
Daytime
running
lamps on.a manual selection or
automatic illumination of
headlamps.
Turn
  the   ring   on   the   lighting   control   stalk   to   the  
second

  position.
illumination of the dipped beam headlamps
from  the   time   the   ignition   is   switched   on: daytime running lamps (depending on the


country
  in   which   the   vehicle   is   sold).
Chapter 4, "Steering mounted controls" section.
Main beam
headlamps pullin
g
 
of
 
the
 
stalk
 
towards
 
you. Pull

  the   stalk   to   return   to   dipped   beam  
headlamps.
Direction
indicators flashing

 
with
 
audible

 
signal. a change of direction via
the
 
lighting
 
stalk. Flashing
  right:   push   stalk   downwards.
Flashing
  left:   push   stalk   upwards.
Front
foglamps on.
a
 
manual
 
selection. The foglamps only operate if the sidelamps or
dipped
  beam   headlamps   are   on.
Rear
foglamps on.
a
 
manual
 
selection. The foglamps only operate if the sidelamps or
dipped
  beam   headlamps   are   on.
In conditions of normal visibility, switch them off
to
  avoid   breaking   the   law.
"This
  lamp   is   a   dazzling   red".

48
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Trip recorder zero
reset button
After this operation, if you wish
to  disconnect   the   battery,   lock  
the

 
vehicle   and   wait   for   at   least   five  
minutes, otherwise the zero re-set will
not

 
be   registered.
Engine oil level indicator
Depending on your vehicle's engine,
when the ignition is switched on,
the engine oil level is indicated for
a few seconds, after the service
information. Oil level
correct
Low oil level
Flashing of "OIL",
linked
  with   the  
service warning lamp,
accompanied by an
audible signal and a message in the
screen, indicates a low oil level which
could
  damage   the   engine.
If   the   low   oil   level   is   confirmed   by   a  
check

  using   the   dipstick,   it   is   essential  
that

  the   level   is   topped   up.
Oil level gauge
fault
Flashing of "OIL--"
indicates a
malfunction of the
engine   oil   level   indicator.   Contact  
a

  CITROËN   dealer   or   a   qualified  
workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been of
f for
more
  than   30   minutes.Dipstick
A = maximum, never exceed
this level as a surplus of oil
may
  damage   the   engine.
Contact a CITROËN dealer
or   a   qualified   workshop  
without

  delay.
B = minimum, top up the level
via   the   oil   filler   cap,   using   the  
grade of oil suited to your
engine.
Lighting dimmer
With the ignition on, press
the button until the zeros
appear.
With the lighting on,
press the button to vary
the brightness of the
instruments
  and   controls.  
When the lighting reaches
the minimum


(or maximum) setting, release the
button then press it again to increase
(or
 
reduce)
 
the   brightness.
As soon as the lighting is of the
required
 
brightness,   release   the   button.
Zero reset
Your CITROËN dealer or a qualified workshop  carries   out   this   operation  
after

  each   service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-

switch of
f the ignition,
-

press and hold the trip recorder
reset button,
-

 
switch
  on   the   ignition.
The
  display   begins   a   countdown.
When the display shows "=0", release
the
  button;   the   spanner   disappears.

49
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
MANUAL GEARBO x
5-speed
6-speed
To change gear easily, always depress
the
 
clutch
 
pedal   fully.
To prevent the mat from becoming
caught
 
under
 
the   pedal:
-

ensure that the mat is positioned
and

 
secured   correctly   on   the   floor,
-
 
never

 
fit
 
one   mat   on   top   of   another.
When driving, avoid leaving your hand
on
 
the
 
gear
 
knob   as   the   force   exerted,  
even if slight, may wear the internal
components

 
of
  the   gearbox   over   time.
Changing into 5th or 6th gear
To engage the gear correctly, move the
gear  lever   fully   to   the   right.
Engaging reverse gear
The lever should be moved slowly
to  reduce   noise.
To engage reverse gear, wait until the
vehicle
  has   come   to   a   complete   stop.
STEERING WHEEL ADJUSTMENT
When the vehicle is stationary,
release
  the   steering   wheel   adjustment  
mechanism

  by   pulling   the   lever.
Adjust
  the   steering   wheel   for   height  
and

  reach,   then   lock   the   mechanism   by  
pushing

  the   lever   fully   forward. In
  the   6-speed   configuration,   raise   the  collar
  below   the   gear   knob.
READY TO GO
3
Gearbox and steering wheel

53
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
STOP & START
The Stop & Start system puts the
engine temporarily on standby - ST OP
mode
  -   during   stops   in   the   traffic   (red  
lights,

  traffic   jams,   or   other...).
The engine restarts automatically -
START mode - as soon as you want to
move
  off.
The
  restart   takes   place   instantly,  
quickly

  and   silently.
Perfect for urban use, the Stop & Start
system reduces fuel consumption and
exhaust emissions as well as the noise
level
  when   stationary.
Operation
Going into engine STOP modeThe "ECO" warning lamp
comes on in the instrument
panel and the engine goes
into
  standby:
-

with a manual gearbox
, at speeds
below
  12   mph   (20   km/h),   when   you  
put the gear lever into neutral and
release the clutch pedal,
-


with a 6-speed electronic
gearbox

, at speeds below 5 mph
(8
  km/h),   when   you   press   the   brake  
pedal or put the gear lever into
position

N. If
  your   vehicle   is   fitted   with   the   system,  
a time counter calculates the sum of
the periods in ST

OP mode during a
journey.   It   rests   itself   to   zero   every   time  
the

  ignition   is   switched   on   with   the   key.
With a 6-speed electronic
gearbox, for your comfort during
parking   manoeuvres,   STOP
 
mode  
is not available for a few seconds after
coming

  out   of   reverse   gear.
STOP mode does not affect the
functionality of the vehicle, such as
braking,   power   steering,   for   example.
Never refuel with the engine in
STOP mode; you must switch off
the   ignition   with   the   key.Special cases: STOP mode
unavailable
STOP
 

mode   is   not   invoked   when:
-
the vehicle is on a steep slope
(rising or fallin

g),
-
the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded

6   mph   (10   km/h)   since   the   last  
engine

  start   using   the   key,
-
the engine is needed to maintain
a comfortable temperature in the
passenger compartment,
-

demisting is on,
-

some special conditions (battery
charge, engine temperature,
braking

  assistance,   ambient  temperature...)
  where   the   engine  is needed to assure control of a
system.
In this case, the
"ECO"
warning
  lamp   flashes   for   a  
few

  seconds,   then   goes   off.
This operation is perfectly normal.
READY TO GO
3
Stop & Start

57
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Starting and switching off
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
DRIVING RECOMMENDATIONS
Observe the driving regulations and
remain  vigilant   whatever   the   traffic  
conditions.
Pay

  close   attention   to   the   traffic   and  
keep

  your   hands   on   the   wheel   so   that  
you are ready to react at any time to
any

  eventuality.
As a safety precaution, the driver
must only carry out actions requiring
sustained attention when the vehicle is
stationary.
On
  a   long   journey,   a   break   every  
two hours

  is   strongly   recommended.
In
  difficult   weather,   drive   smoothly,  
anticipate

  the   need   to   brake   and  
increase the distance from other
vehicles.
Driving on flooded roads
We strongly advise against driving
on  flooded   roads,   as   this   could   cause  
serious damage to the engine or
gearbox, as well as to the electrical
systems

  of   your   vehicle. If you are obliged to drive through
water:
-
 
check
  that   the   depth   of   water   does  
not

  exceed   15   cm,   taking   account  
of waves that might be generated
by other users,
-

deactivate the Stop & Start system,
-

drive as slowly as possible without
stallin

g.   In   all   cases,   do   not   exceed  6
  mph   (10   km/h),
- do not stop and do not switch of f
the
  engine.
On
  leaving   the   flooded   road,   as   soon  
as

  circumstances   allow,   make   several  
light

  brake   applications   to   dry   the   brake  
discs

  and   pads.
If in doubt on the state of your vehicle,
contact a CITROËN dealer or a
qualified
  workshop.Never
  drive   with   the   parking   brake  
applied

  -   Risk   of   overheating   and  
damage

  to   the   braking   system!
Risk   of   fire!
As the exhaust system of your vehicle
is very hot, even several minutes
after switching off the engine, do not
park   or   leave   the   engine   running   over  
areas

  where   inflammable   substances  
and

  materials   are   present:   grass,  
leaves, etc.
Never leave a vehicle
unsupervised with the engine
running.
  If   you   have   to   leave  your vehicle with the engine running,
apply
  the   parking   brake   and   put   the  
gearbox into neutral or position

N or P,
depending
  on   the   type   of   gearbox.
Important!
READY TO GO
3