2017 Citroen BERLINGO MULTISPACE RHD light

58
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
DIRECTION INDICATORS
"Motorway" function
Press  the   control   up   or   down   to   flash  
the corresponding direction indicator
three

  times.
LIGHTING
Left: downwards passing the point  of   resistance.
Right:
  upwards   passing   the  
point

  of   resistance.
Front and rear lighting
Lighting off
Automatic illumination of
headlamps
Sidelamps
Dipped beam (green)
Dipped beam/main beam change
Pull
 
the
 
stalk   fully   towards   you.
Lighting-on audible warning
On switching off the ignition, all of the
lamps turn off, except dipped beam if
automatic guide-me-home lighting has
been
 
activated.
 Checking

 
by
 
means
 
of
 
the
 
indicator
 lamps in the instrument panel is


described in the "Instruments and
controls"
 
section
 
of
 
chapter
 
3.
Direction indicators
Selection is by turning this
ring. Main beam (blue)
To activate the lighting
control, turn this ring to
the lighting off position "0"
then to the selection of
your   choice.
On opening the driver's door, there is
an audible warning if you have left the
lighting
  on.
Steering mounted controls

59
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
LED DAYTIME RUNNING LAMPS
Rear foglamps (amber,
2nd rotation of the ring
forwards).
Front foglamps (green,
1st
rotation of the ring
forwards). Rotate this ring forwards
to switch on and
rearwards   to   switch   off.
Their   state   is   confirmed   by  
the warning lamps in the
instrument

  panel. Do not forget to switch them off
when   they   are   no   longer   needed.
Operation of the automatic illumination
of headlamps switches off the rear
foglamps, but the front foglamps
remain   on.
To switch off the front and
rear foglamps, turn the
ring rearwards twice in
succession.
Automatic illumination of headlamps
In foggy weather or in snow,
the sunshine sensor may detect
sufficient   light.
As a consequence, the lighting
will
  not   come   on   automatically.   If  
necessary

, you must switch on
the dipped
  beam   headlamps   manually.
Do not cover the sunshine sensor
located on the windscreen, behind
the
 
mirror.   It   is   used   for   the   automatic  
illu

mination of headlamps and for the
automatic
  rain   sensitive   wipers.
Activation The sidelamps
and dipped beam
headlamps switch
on automatically if
the light is poor, or
during operation of the windscreen
wipers.  
They
  switch   off   as   soon   as   the  
light becomes bright enough or the
windscreen

  wipers   stop.
On starting the vehicle, in daylight the
LED daytime running lamps come on
automatically.
If the sidelamps and headlamps are
switched on manually or automatically,
the
 
daytime
 
running
 
lamps
 
go
 
off.
Programming
For countries where exterior lighting by
day is not a legal requirement, you can
activate or deactivate the function via
the   configuration   menu.
If the user does not operate any
equipment for 30 minutes, the
Economy mode engages to avoid
discharging
 
the
 
battery.
 
Electrical
 
functions are put on standby and the
battery

 
warning
 
lamp
 
flashes.
Sidelamp operation is not affected by
Economy
 
mode.
In clear weather or in rain, both day
and night, rear foglamps dazzle and
their  use   is   prohibited.
Refer to chapter 8, "Battery
section".
Front and rear foglamps
They operate with the sidelamps and
dipped
 
beam
 
headlamps.
Turn the ring to the AUTO  position.  The activation of this function is
accompanied by a message in the
screen.
Deactivation
T
urn   the   ring   forwards   or   rearwards.  
The deactivation of this function is
accompanied by a message in the
screen. This function is not compatible with
daytime
  running   lamps.
Steering mounted controls
EASE OF USE and COMFORT
4

60
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
If the sunshine sensor
does not function correctly,
the lighting comes on
accompanied by the service
warning lamp, an audible
signal
 
and   a   message   in   the   screen.
Contact a CITROËN dealer or a
qualified
  workshop.
Guide-me-home lighting
Keeping the dipped beam headlamps
on temporarily with the ignition off,
makes   the   driver's   exit   easier   when   the  
light

  is   poor.
HEADLAMP BEAM
The beam setting must be adjusted to suit
  the   load   in   the   vehicle.
0 -
  No   load.
1 -
  Partial   load.
2 -
 
A
verage   load.
3 -
  Maximum   authorised   load.
Manual operation
-
 
With

 
the
 
ignition
 
off,
 
"flash"
 
the
 
headlamps within one minute after
switching

 
off
 
the
 
ignition.
The guide-me-home lighting switches
off
 
automatically
 
after
 
a
 
set
 
time.
Automatic operation
Refer to chapter 10, "Screen
menu
 
map"
 
section. Initial setting is position 0.
Activate the function via the
vehicle
 
configuration
 
menu. Programming
The system is activated or deactivated
in
 
the
 
vehicle
 
configuration
 
menu.
The
 
system
 
is
 
activated
 
by
 
default.
Switching off
The
 
system
 
does
 
not
 
operate:
-

below a certain angle of rotation of
the steering wheel,
-

 
above

 
25
 
mph
 
(40
 
km/h),
-
 
when

 
reverse
 
gear
 
is
 
engaged.
Switching on
This
 
function
 
starts:
-

when the corresponding direction
indicator is switched on,
or
-


from a certain angle of rotation of
the

 
steering
 
wheel.
With dipped or main beam headlamps,
this
 
function
 
makes
 
use
 
of
 
the
 
beam
 
from a front foglamp to illu

minate the
inside of a bend, when the vehicle
speed is below 25 mph (approximately
40
 
km/h)
 
(urban
 
driving,
 
winding
 
road,
 
intersections,

 
parking
 
manoeuvres...).
CORNERING LIGHTING
Travelling abroad
If using your vehicle in a country
that drives on the other side of the
road,
  the   headlamps   must   be   adjusted  
to

 
avoid   dazzling   on-coming   drivers.
Contact a CITROËN dealer or a
qualified
  workshop.
The function is deactivated temporarily
when you use the manual lighting
control
 
stalk.
Steering mounted controls

91
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
Operating the Row 3 seats
Removing the seat
- 
Lower
  the   head   restraint.
-

Place the seat in the fully folded
position.
-

 
T
ilt   the   entire   seat   forwards.
-
 
On
  each   side,   take   hold   of   the  
uprights of the folded seat, tilting it
forward

  slightly,   and   lift   it.Refitting the seat
The label on the seat indicates the
position
  in   which   it   must   be   installed.
-
 
Place
  the   hooks   of   the   front   feet  
between

  the   two   bars.
-
 
Ensure
  that   no   object   or   foot   is  
obstructing the rear anchorage
points and that the seat belt is
positioned correctly and available
for

  use.
-
 
Fold
  back   the   seat   to   fix   its   rear  
anchoring

  feet.
-

Operate the control to raise the
seat

  back   to   its   initial   position.
-
 
Raise
  the   head   restraint.
Good practice
Following the various operations:
-
do not remove a head restraint
without stowing it; secure it inside
the vehicle,
-


ensure that the passengers can
always access the seat belts and
fasten them easily

,
-
 
passengers
  must   never   take  
their

  seat   without   adjusting   and  
fastening

  their   seat   belt.
-

a passenger seated in row 3 must
ensure that he does not obstruct
the row 2 seat anchorage points,
-


a passenger seated in row 3 must
not have the seat in front of them in
row 2 in the folded position; this is
in case the seat could tip towards
the passenger unexpectedly and
injure

  them.
Do
  not   place   hard   or   heavy   objects   on  
the

  seat   backs   forming   a   table,   they  
could

  become   dangerous   projectiles   in  
the

  event   or   sharp   braking   or   impact.
EASE OF USE and COMFORT
4
Seats

96
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
SEATING AREA FITTINGS
Floor boxes
Two boxes are available, located under
the  rear   passenger   footwells.
To
  open   them,   slide   your   fingers   into  
the

  recess   and   lift   the   lid.
Aircraft style tables
To put the table in place, pull it
upwards  and   fold   it   down.
As a safety precaution, above a high
pressure, the table is designed to
unhook.
To
  put   it   back   in   place,   with   the   table  
vertical, engage one side then the
other

,   forcing   slightly.
Do
  not   place   hard   or   heavy   objects  
on

  the   table.  
They
  could   become  
dangerous

  projectiles   in   the   event   of  
sharp

  braking   or   impact.
A
 

bag   hook   is   provided   on   the   side   of  
each

  table.
Side blinds
Side blinds may be available on the
sliding   side   doors.
Pull the side blind by the tab to install it.
To avoid damaging the blind when
opening  the   door,   check   that   the   tab   is  
hooked

  securely.
Always guide the blind slowly
using the tab, both when raising
and
  when   lowering.
Practical information

11 4
Berlingo2VP_en_Chap05_Securite_ed02-2016
HAZARD WARNING LAMPS
H
ORN
Press the centre of the steering wheel.
PARKING BRAKE
Applying
Pull the parking brake lever up to immobilise
  your   vehicle.
Check
  that   the   parking   brake   is   applied  
firmly

  before   leaving   the   vehicle.Pull
  on   the   parking   brake   lever,   only
with the vehicle stationary.
In the exceptional case of use of the
parking
  brake   when   the   vehicle   is  
moving,

  apply   the   brake   by   pulling  
gently

  to   avoid   locking   the   rear   wheels  
(risk

  of   skidding).
Press this button, the direction
indicators
 
flash.
They
 
can
 
operate
 
with
 
the
 
ignition
 
off.
The hazard warning lamps should only
be used in dangerous situations, when
stopping in an emergency or when
driving
 
in
 
unusual
 
conditions.
When
  parking   on   a   slope,   direct   your  
wheels towards the pavement and pull
the

  parking   brake   lever   up.
There is no advantage in engaging
a
  gear   after   parking   the   vehicle,  
particularly

  if   the   vehicle   is   loaded.
If the parking brake is still on or has not been released properly, this is
indicated by this warning lamp which
comes
  on   in   the   instrument   panel.
Automatic operation of hazard
warning lamps
When braking in an emergency, depending on the force of deceleration,
the hazard warning lamps come
on  automatically.  
They
  switch   off  
automatically

  the   first   time   you  
accelerate.
It is also possible to switch them of

f by
pressing
  the   switch   on   the   dashboard.Releasing
Pull the lever up slightly and press the
button  to   lower   the   parking   brake   lever.
Driving safely

ABS
ABS
11 8
Berlingo2VP_en_Chap05_Securite_ed02-2016
ANTI-LOCK BRAKING SYSTEM
(ABS / EBFD)
The ABS   and   EBFD   (electronic   brake  force distribution) systems improve the
stability and manoeuvrability of your
vehicle
  on   braking,   in   particular   on  
poor

  or   slippery   surfaces.
The
 
ABS
  prevents   locking   of   the  
wheels, the EBFD provides control of
the

  braking   pressure   wheel   by   wheel.If this warning lamp comes
on, accompanied by an
audible signal and a message
in the screen, it indicates a
malfunction of the ABS which
could result in a loss of control of the
vehicle
  on   braking.
If this warning lamp comes
on,
  together   with   the   brake  
and ST

OP warning lamps,
accompanied by an audible
signal and a message in the
screen, it indicates a malfunction of
the
  electronic   brake   force   distribution  
which could result in a loss of control of
the

  vehicle   on   braking.
EMERGENCY BRAKING
ASSIST

ANCE (EBA)
In an emergency, this system enables
the  optimum   braking   pressure   to   be  
reached

  more   quickly,   press   the   pedal  
firmly

  without   releasing   it.
It is triggered by the speed at which the
brake
  pedal   is   pressed   down.
This
  alters   the   resistance   of   the   brake  
pedal

  under   your   foot.
To maintain operation of the
emergency
  braking   assistance   system:  
keep

  your   foot   on   the   brake   pedal.
Good practice
The anti-lock braking system comes into operation automatically when
there  is   a   risk   of   wheel   lock.   It   does   not  
reduce

  the   braking   distance.
On very slippery surfaces (ice,
oil, etc...)
  the  
ABS
  may   increase   the  
braking

  distance.   When   braking   in  
an emergency

, do not hesitate to
press
  the   brake   pedal   firmly,   without  
releasing the pressure, even on a
slippery surface, you will then be able
to continue to manoeuvre the vehicle
to

  avoid   an   obstacle.
Normal operation of the ABS may be
felt
  by   slight   vibration   of   the   brake  
pedal.
When changing wheels (tyres and
rims), ensure that these are listed by
CITROËN

  for   the   vehicle. Stop as soon as it is safe to do so.
In both cases, contact a CITROËN
dealer
  or   a   qualified   workshop.
Driving safely

126
Berlingo2VP_en_Chap05_Securite_ed02-2016
126
Berlingo2VP_en_Chap05_Securite_ed02-2016
SEAT BELTS
Height adjustment
Squeeze the control with the return and
slide the assembly on the driver's seat
side and on the individual passenger
seat  side.
Fastening
Pull the strap, then insert the tongue
into  the   buckle.
Check
  that   the   seat   belt   is   fastened  
correctly

  by   pulling   the   strap.
Seat belt(s) not fastened
warning lamp Unfastening
Press the red button.
When the vehicle is started,
this warning lamp comes on
if a user at the front has not
fastened
  their   seat   belt.
Good practice
The driver must ensure that
passengers use the seat belts correctly
and that they are all strapped in
securely  before   moving   off.
Wherever you are seated in the
vehicle, always fasten your seat belt,
even
  for   short   journeys.
The
  seat   belts   are   fitted   with   an   inertia  
reel

  which   automatically   adjusts   the  
length

  of   the   strap   to   your   size.
Do not use accessories (clothes pegs,
clips,
  safety   pins,   etc.)   which   allow   the  
seat

  belt   straps   to   fit   loosely.
Ensure that the seat belt has reeled in
correctly
  after   use.
After folding or moving a seat or a rear
bench seat, ensure that the seat belt
has reeled in correctly and that the
buckle
  is   ready   to   accommodate   the  
tongue.
Depending on the nature and
seriousness of any impact, the
pretensioning device may be deployed
before

  and   independently   of   inflation  
of

  the   airbags.   It   instantly   tightens  
the seat belts against the body of the
occupants.
Deployment of the pretensioners is
accompanied by a slight discharge
of

  harmless   smoke   and   a   noise,   due  
to the activation of the pyrotechnic
cartridge

  incorporated   in   the   system.
The front passenger's seat may be
fitted
 
with

 
a

 
presence

 
detector

,
 
in

 
which

 
case you should not place anything
heavy on this seat as this could trigger
the

 
alert.
Seat belts