2017 CHEVROLET SILVERADO fuel

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
314 Driving and Operating
Warning (Continued)
.Fuel can spray out if therefueling nozzle is insertedtoo quickly. This spray canhappen if the tank is nearlyfull, and is more likely in hotweather. Insert the refuelingnozzle slowly and wait forany hiss noise to stop priorto beginning to flow fuel.
The vehicle has a capless refuelingsystem and does not have a fuelcap. The filling nozzle must be fullyinserted and latched prior to startingfuel flow.
{Warning
Overfilling the fuel tank by more
than three clicks of a standard fill
nozzle may cause:
.Vehicle performance issues,including engine stalling anddamage to the fuel system.
.Fuel spills.
.Potential fuel fires.
Be careful not to spill fuel. Wait afew seconds after you have finishedpumping before removing thenozzle. Clean fuel from paintedsurfaces as soon as possible. SeeExterior Care0441.
{Warning
If a fire starts while you are
refueling, do not remove the
nozzle. Shut off the flow of fuel by
shutting off the pump or by
notifying the station attendant.
Leave the area immediately.
For models with dual fuel tanks, thefuel gauge shows an average ofboth tanks. The rear tank is emptiedfirst. When refueling, refuel the fronttank first, then add fuel to therear tank.
Filling the Tank With a PortableGas Can
If the vehicle runs out of fuel andmust be filled from a portablegas can:
1. Locate the capless funneladapter from inside the vehicle.
2. Insert and latch the funnel intothe capless fuel system.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
Driving and Operating 315
{Warning
Attempting to refuel without using
the funnel adapter may cause fuel
spillage and damage the capless
fuel system. This could cause a
fire and you or others could be
badly burned and the vehicle
could be damaged.
3. Remove and clean the funneladapter and return to thestorage location.
Filling a Portable Fuel
Container
{Warning
Filling a portable fuel container
while it is in the vehicle can cause
fuel vapors that can ignite either
by static electricity or other
(Continued)
Warning (Continued)
means. You or others could be
badly burned and the vehicle
could be damaged. Always:
.Use approved fuelcontainers.
.Remove the container fromthe vehicle, trunk, or pickupbed before filling.
.Place the container on theground.
.Place the nozzle inside thefill opening of the containerbefore dispensing fuel, andkeep it in contact with the fillopening until filling iscomplete.
.Fill the container no morethan 95% full to allow forexpansion.
.Do not smoke, lightmatches, or use lighterswhile pumping fuel.
.Avoid using cell phones orother electronic devices.
Trailer Towing
General Towing
Information
Only use towing equipment that hasbeen designed for the vehicle.Contact your dealer or traileringdealer for assistance with preparingthe vehicle for towing a trailer. Readthe entire section before towing atrailer.
For towing a disabled vehicle, seeTo w i n g t h e V e h i c l e0436.Fortowing the vehicle behind anothervehicle such as a motor home, seeRecreational Vehicle Towing0437.
Driving Characteristics
and Towing Tips
Driving with a Trailer
When towing a trailer:
.Become familiar with the stateand local laws that apply totrailer towing.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
318 Driving and Operating
If parking the rig on a hill:
1. Press the brake pedal, but donot shift into P (Park) yet. Turnthe wheels into the curb iffacing downhill or into traffic iffacing uphill.
2. Have someone place chocksunder the trailer wheels.
3. When the wheel chocks are inplace, release the regularbrakes until the chocks absorbthe load.
4. Reapply the brake pedal. Thenapply the parking brake andshift into P (Park).
5. Release the brake pedal.
Leaving After Parking on a Hill
1. Apply and hold the brakepedal.
2. Start the engine.
3. Shift into a gear.
4. Release the parking brake.
5. Let up on the brake pedal.
6. Drive slowly until the trailer isclear of the chocks.
7. Stop and have someone pickup and store the chocks.
Maintenance when Trailer
Towing
The vehicle needs service moreoften when pulling a trailer. SeeMaintenance Schedule0452.Things that are especially importantin trailer operation are automatictransmission fluid, engine oil, axlelubricant, belts, cooling system, andbrake system. It is a good idea toinspect these before and duringthe trip.
Check periodically to see that allhitch nuts and bolts are tight.
Trailer Towing
If the vehicle has a diesel engine,see the Duramax dieselsupplement.
If the vehicle is bi-fuel, see thebi-fuel supplement.
Do not tow a trailer during break-in.SeeNew Vehicle Break-In0267.
{Warning
The driver can lose control when
pulling a trailer if the correct
equipment is not used or the
vehicle is not driven properly. For
example, if the trailer is too heavy
or the trailer brakes are
inadequate for the load, the
vehicle may not stop as expected.
The driver and passengers could
be seriously injured. The vehicle
may also be damaged; the
resulting repairs would not be
covered by the vehicle warranty.
Pull a trailer only if all the steps in
this section have been followed.
Ask your dealer for advice and
information about towing a trailer
with the vehicle.
Caution
Pulling a trailer improperly can
damage the vehicle and result in
costly repairs not covered by the
(Continued)

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
Driving and Operating 319
Caution (Continued)
vehicle warranty. To pull a trailer
correctly, follow the advice in this
section and see your dealer for
important information about
towing a trailer with the vehicle.
SeeVehicle Load Limits0259formore information about the vehicle'smaximum load capacity.
To i d e n t i f y t h e t r a i l e r i n g c a p a c i t y o fthe vehicle, read the information in“Weight of the Trailer”later in thissection.
Trailering is different than justdriving the vehicle by itself.Trailering means changes inhandling, acceleration, braking,durability, and fuel economy.Successful, safe trailering takescorrect equipment, and it has to beused properly.
The following information has manytime-tested, important trailering tipsand safety rules. Many of these are
important for your safety and that ofyour passengers. Read this sectioncarefully before pulling a trailer.
Weight of the Trailer
Safe trailering requires monitoringthe weight, speed, altitude, roadgrades, outside temperature, andhow frequently the vehicle is used topull a trailer. Take into considerationany special equipment on thevehicle, and the amount of tongueweight the vehicle can carry. See“Weight of the Trailer Tongue”laterin this section for more information.
Trailer weight rating (TWR) forpickup models is calculatedassuming the tow vehicle has thedriver, a front seat passenger, andall required trailering equipment.Weight of additional optionalequipment, passengers, and cargoin the tow vehicle must besubtracted from the trailer weightrating.
Ask your dealer for traileringinformation or advice.
For kingpin weight and trailertongue weight information, see“Weight of the Trailer Tongue”laterin this section.
Use the following chart to determinehow much the vehicle can weigh,based upon the vehicle model andoptions.
Weights listed apply forconventional trailers andgooseneck/fifth-wheel trailers unlessotherwise noted.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
340 Driving and Operating
selection of Tow/Haul when thevehicle is unloaded. Such aselection when unloaded may resultin unpleasant engine andtransmission driving characteristicsand reduced fuel economy. Tow/Haul is recommended only whenpulling a heavy trailer or a large orheavy load.
Integrated Trailer Brake
Control System
The vehicle may have an IntegratedTrailer Brake Control (ITBC) systemfor use with electric trailer brakes ormost electric over hydraulic trailerbrakes.
This symbol is on the Trailer BrakeControl Panel on vehicles with anITBC system. The power output tothe trailer brakes is based on theamount of brake pressure beingapplied by the vehicle’sbrake
system, and on the type of trailerbrakes detected. This availablepower output to the trailer brakescan be adjusted to a wide range oftrailering situations.
The ITBC system is integrated withthe vehicle’sbrake,antilockbrake,and StabiliTrak systems. In traileringconditions that cause the vehicle’santilock brake or StabiliTraksystems to activate, power sent tothe trailer's brakes will beautomatically adjusted to minimizetrailer wheel lock-up. This does notimply that the trailer has StabiliTrak.
If the vehicle’sbrake,antilockbrake,or StabiliTrak systems are notfunctioning properly, the ITBCsystem may not be fully functionalor may not function at all. Make sureall of these systems are fullyoperational to ensure fullfunctionality of the ITBC system.
The ITBC system is poweredthrough the vehicle's electricalsystem. Turning the ignition off willalso turn off the ITBC system. TheITBC system is fully functional onlywhen the ignition is in ON/RUN.
{Warning
Connecting a trailer that has an
air brake system may result in
reduced or complete loss of trailer
braking. There may be an
increase in stopping distance or
trailer instability which could
result in personal injury or
damage to the vehicle, trailer,
or other property. Use the ITBC
system only with electric or
electric over hydraulic trailer
brakes.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
Driving and Operating 347
Front axle reserve capacity is thedifference between the Gross AxleWeight Rating (GAWR) and the frontaxle weight of the vehicle with fullfuel and passengers. This is theamount of weight that can be addedto the front axle before reaching thefront GAWR.
United States
Canada
The front axle reserve capacity forthe vehicle is in the lower rightcorner of the Certification/Tire label.
To c a l c u l a t e t h e a m o u n t o f w e i g h tany front accessory, such as a snowplow, is adding to the front axle, usethis formula:
(W x (A + W.B.)) /W.B.= Weight theaccessory is adding to thefront axle.
Where:W=WeightofaddedaccessoryA=Distancethattheaccessoryis in front of the front axleW.B. = Vehicle Wheelbase

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
348 Driving and Operating
For example, adding a 318 kg(700 lb) snow plow actually addsmore than 318 kg (700 lb) to thefront axle. Using the formula, if thesnow plow is 122 cm (4 ft) in front ofthe front axle and the wheelbase is305 cm (10 ft), then:W=318kg(700lb)A=122cm(4ft)W.B. = 305 cm (10 ft)
(W x (A + W.B.)/W.B. =(318 x (122 + 305))/305 = 445 kg(980 lb)
This means if the front axle reservecapacity is more than 445 kg(980 lb), the snow plow could beadded without exceeding thefront GAWR.
Heavier equipment can be added onthe front of the vehicle if less cargoor fewer passengers are carried,or by positioning cargo toward therear. This reduces the load on thefront. However, the front GAWR,rear GAWR, and Gross VehicleWeight Rating (GVWR) must neverbe exceeded.
{Warning
On some vehicles that have
certain front mounted equipment,
such as a snow plow, it may be
possible to load the front axle to
the front Gross Axle Weight
Rating (GAWR) but not have
enough weight on the rear axle to
have proper braking performance.
If the brakes cannot work
properly, the vehice could crash.
Always follow the snow plow
manufacturer or installer's
recommendation for rear ballast
to ensure a proper front and rear
weight distribution ratio.
Maintaining a proper front and
rear weight distribution ratio is
necessary to provide proper
braking performance.
To t a l v e h i c l e r e s e r v e c a p a c i t y i s t h edifference between the GVWR andthe weight of the truck with full fueland passengers. It is the amount ofweight that can be added to thevehicle before reaching the GVWR.Reserve capacity numbers are
intended as a guide when selectingthe amount of equipment or cargothe truck can carry. If unsure of thevehicle's front, rear, or total weight,go to a weigh station and weigh thevehicle. Your dealer can also helpwith this.
The total vehicle reserve capacityfor the vehicle is in the lower rightcorner of the Certification/Tire labelas shown previously.
See your dealer for additionaladvice and information about usingasnowplowonthevehicle.Also,seeVehicle Load Limits0259.
Emergency Roof Lamp
Provisions
Vehicles with the RPO VYU snowplow prep package also have anemergency roof lamp provisionpackage, RPO TRW. Wiring for theemergency roof lamp is providedabove the overhead console. SeeAuxiliary Roof-Mounted Lamp0176for switch location.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
374 Vehicle Care
Overheated Engine
Protection
Operating Mode
If an overheated engine conditionexists and the ENGINE POWER ISREDUCED message displays, anoverheat protection mode whichalternates firing groups of cylindershelps to prevent engine damage. Inthis mode, a loss in power andengine performance will be noticed.This operating mode allows thevehicle to be driven to a safe placein an emergency. Driving extendeddistances and/or towing a trailer inthe overheat protection modeshould be avoided.
Caution
After driving in the overheated
engine protection operating
mode, the engine oil will be
severely degraded. Any repairs
performed before the engine is
cool may cause engine damage.
Allow the engine to cool before
(Continued)
Caution (Continued)
attempting any repair. Repair the
cause of coolant loss, change the
oil, and reset the oil life system.
SeeEngine Oil0359.
Engine Fan
If the vehicle has a clutched enginecooling fan, when the clutch isengaged, the fan spins faster toprovide more air to cool the engine.In most everyday driving conditions,the fan is spinning slower and theclutch is not fully engaged. Thisimproves fuel economy and reducesfan noise. Under heavy vehicleloading, trailer towing, and/or highoutside temperatures, the fan speedincreases as the clutch more fullyengages, so an increase in fannoise may be heard. This is normaland should not be mistaken as thetransmission slipping or makingextra shifts. It is merely the coolingsystem functioning properly. The fanwill slow down when additionalcooling is not required and theclutch disengages.
This fan noise may also be heardwhen starting the engine. It will goaway as the fan clutch partiallydisengages.
If the vehicle has electric coolingfan(s), the fans may be heardspinning at low speed during mosteveryday driving. The fans may turnoff if no cooling is required. Underheavy vehicle loading, trailer towing,high outside temperatures,or operation of the air conditioningsystem, the fans may change tohigh speed and an increase in fannoise may be heard. This is normaland indicates that the coolingsystem is functioning properly. Thefans will change to low speed whenadditional cooling is no longerrequired.
The electric engine cooling fansmay run after the engine has beenturned. off. This is normal and noservice is required.