2017 CHEVROLET LOW CAB FORWARD light

Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
290 Vehicle Care
Bulb Wattage
PositionLights Bulb Wattage (12V)Qty.
Front Headlight Highbeam/Lowbeam
60/55W2
Front Turn Signal Lamp 27W (Amber)2
Parking Lamp 5W2
Cornering Lamp 27W2
Side Turn Signal Lamp 5W (Amber)2
Sidemarker Lamp 5W (Amber)2
Rear Taillamp and Stoplamp
8/27W2
Turn Signal Lamp 27W2
Back-Up Lamp 27W2
License Plate Lamp 7.5W1
Roof Roofmarker Lamp
(Identification/Clearance Lamp) 5W
5
Interior Dome Light
10W1
Speedometer and Gauge Lights 3.4W5
Warning/Indicator Lights LED20

Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
Vehicle Care 291
Contact your dealer when replacing
lights that are not listed here.
Headlamps and Front
Turn Signal
Replacing the Headlamps
When the bulb has blown out,
replace it with a bulb of the
specified wattage. Be careful not to
excessively tighten the mounting
screws when replacing the
headlamp bulbs.
Do not replace a bulb with other
than the specified wattage.
Proper aiming of the headlamps is
important to ensure sufficient
illumination of the highway without
blinding other motorists. When
replacing headlamp bulbs, have the
headlamp aim adjusted at your
dealer.
When replacing a bulb, make sure
the light switch is“OFF”.
See Bulb Replacement 0288.
1. Remove the front grille (3).
Remove the screw (4) from the
center of the grille. Push up on
the tabs of the five clips (1) on
the upper side of the grille and
pull the grille toward you to
remove it. Loosen the nuts (2)
for the turn signal light.2. Remove the turn signal lamp.Open the front door. Use a
phillips head screwdriver to
remove the two screws
between the door and the cab.

Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
294 Vehicle Care
3. To install the lamps, performthe same sequence of
operations in reverse, taking
care to turn the connector
clockwise to lock it securely.
If the socket is not locked securely,
water could get inside the lamp and
lead to a breakdown.
Replacing a Front Turn
Signal Lamp
Do not replace a bulb with other
than the specified wattage. This will
cause abnormal flashing,
particularly for turn signal lamps. When replacing a bulb, make sure
the light switch is OFF.
1. While referring to “Replacing
the Headlights”, tilt the turn
signal lamp assembly down
toward the front of the vehicle
and remove it.
2. Disconnect the connector for the turn signal light and then
remove the socket.
3. Pull the bulb from the socketand replace it with a new one.
4. To install the lamps, perform the same sequence of
operations in reverse, taking
care to turn the connector
clockwise to lock it securely.
If the socket is not locked securely,
water could get inside the light and
lead to a breakdown.

Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
Vehicle Care 295
Roofmarker Lamps
1. Loosen the screws (2) andremove the lens (1).
2. Remove the bulb (3) from the socket (4) and replace it with a
new one.
3. To install the lights, follow the removal procedure in reverse.
If the screwing procedure is
inadequate, water may infiltrate into
the lamp unit.
Sidemarker Lamps
(Including Turn Signal
and Cornering Lamps)
Do not replace a bulb with other
than the specified wattage. This will
cause abnormal flashing,
particularly for turn signal lamps.
When replacing a bulb, make sure
the light switch is "OFF".
1. Open the front door, remove the rubber cap (1) in the lower
part of the door, and loosen
the nut (2).
2. Slide the cornering lamp (3)and the side turn signal lamp
forward relative to the vehicle.
Disconnect the clip (1) on the
lamp’s rear side from the door
panel (2) and pull out the lamp.
If you pull out the light rear
section by too much when
removing the clip on the rear
side, the clip on the lamp front
side may be damaged.

Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
296 Vehicle Care
3. When the clip (1) has beenremoved, pull the lamp out
while sliding it out toward the
rear of the vehicle.
4. Loosen the socket by turning it counterclockwise.5. Pull the bulb out from the
socket and replace it with a
new one.
6. To install the lights, perform the same sequence of operations
in reverse taking care of the
following points:
A. Turn the socket clockwiseto lock securely.
If the socket is not locked
securely, water could get
inside the light and lead to
a breakdown.B. Insert the clip on the backof the rear part of the light
into the door panel.
C. Push the front part of the light into the door panel,
and insert the clip on the
back of the front part of the
light in the door panel.

Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
Vehicle Care 297
D. Open the front door, tightenthe nut from the inside of
the door, and install the
rubber cap.
Taillamps, Turn Signal,
Stoplamps, and Back-Up
Lamps
1. Turn Signal Lamp
2. Taillamp/Stoplamp
3. Back-Up Lamp
4. Lens
1. Loosen the screws and remove the lens.
2. Loosen the bulb by turning it counterclockwise while
pressing on it.
3. To install the lights, follow the removal procedure in reverse.
License Plate Lamp
1. Bulb
2. Lens
3. Screw
4. Cover
1. Loosen the screws and removethe cover.
2. Remove the lens.
3. Loosen the bulb by turning it counterclockwise while
pressing on it.
4. To install the lights, follow the removal procedure in reverse.

Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
298 Vehicle Care
Interior Lamps
1. Remove the lens and pull outthe bulb.
2. To install the lights, follow the removal procedure in reverse.
Electrical System
Electrical System
Overload
Electrical System
Following the after-delivery service,
it is the owner's responsibility to
check all wiring periodically for
cracked, chafed or oil-soaked
insulation and maintain it in a clean
and tight condition to ensure
satisfactory operation of the
electrical system.
Replacing the Fuses and Relays
Your vehicle is equipped with fuses
and fusible links to protect your
electrical wiring and equipment in
case of electrical overload.
When the lights do not come on or
flash, or the equipment in the
electrical system does not operate,
check to see if a fuse has blown.
Fuses : In case of an electrical
overload, the fuse will blow and stop
the flow of current in the circuit
before electrical components
become damaged. The cause of the circuit overload
must be identified and corrected
before the blown fuse is replaced,
or else the new fuse will also blow.
Since different circuits handle
different amounts of current, fuses
of various ampere ratings are used.
Be sure to replace a blown fuse with
a fuse of the correct rating.
To know if a fuse is blown or not,
remove the suspected fuse and look
at the wire for a break. If the wire is
broken, replace the fuse with one of
equal amperage rating.
The amperage rating of each fuse is
molded in its head.
Fuses are installed in the fuse
panel.

Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
304 Vehicle Care
Gasoline Engine Relay LocationRelay locations:
No. Description
1 STOP LAMP
2 DAYTIME RUNNING LAMP
3 KEY ON
4 TCM
5 PARKING/NEUTRAL
6 WIPER MAIN
7 HORN
8 WIPER HI LO
9 TRAILER BRAKE
10 –/REAR POWER
WINDOW (if
equipped)
11 –/CHARGE (ENG
RUN) - Gasoline
12 POWER WINDOW
13 HEAD LAMP LO
14 VACUUM PUMP
15 HEAD LAMP HI
16 TAIL LAMP
17 CIGAR LIGHTER