2017 AUDI A7 ECU

Child safety
Please remember that the lower anchorage
points are only intended for installation and at­
tachment of child restraints specifically certified
for use with
LATCH lower anchorages. Child re­
straints that are not equipped with the lower an­
chorage attachments can still be installed in
compliance with the child restraint manufactur­
er's instructions on using vehicle safety belts .
A WARNING
Improper use of LATCH lower anchorages can
cause serious personal injury in an accident.
- Always carefully follow the child restraints
manufacturer's instructions for proper in­
stallation of the child restraint and proper
use of the lower anchorages or safety belts
in your vehicle.
- Never secure or attach any luggage or other
items to the
LATCH lower anchorages.
- Always read and heed the important infor­
mation about child restraints in this chapter
and WARNINGS
¢ page 172, Child safety.
Installing a child restraint with LATCH
lower anchorages
Whenever you install a child restraint always fol­
low the child restraint manufacturer 's instruc­
tions.
Fig. 173 Lowe r an ch orages : proper mou nting
Mounting
.,. Make sure the seatback of the rear seat bench
is in the upright position and securely latched
in place .
.. Attach both hook-on connectors with the spring
catch release on the child safety seat onto the
188 LATCH
lower anchorage so that the connectors
lock into place
¢ fig. 173.
.. Pull on the connector attachments to make
sure they are properly attached to the LATCH
lower anchorage.
.. Pull straps tight following the child restraint
manufacturer's instructions.
Releasing
.. Loosen the tension on the straps following the
child restraint manufacturer's instructions.
.. Depress the spring catches to release the an­
chorage hooks from the lower anchorages .
Remember: Use tether straps to help keep the
child restraint firmly in place.
A WARNING
-
Improper use of the LATCH system can in­
crease the risk of serious personal injury and
death in an accident .
- These anchors were developed only for child safety seats using the "LATCH" system.
- Never attach other child safety seats, belts
or other objects to these anchors .
- Always make sure that you hear a click when
latching the seat in place. If you do not hear
a click the seat is not secure and could fly
forward and hit the interior of the vehicle,
or be ejected from the vehicle.
A WARNING
Improper installation of child restraints will
increase the risk of injury in an accident.
- Always follow the child restraint system
manufacturer's instructions for proper in­
stallation of the child restraint system and
proper use of tether straps as well as the lower anchorages or safety belts in your ve­
hicle.
- Always read and heed the important infor­
mation and WARNINGS about child safety
and the installation of child restraint sys­
tems¢
page 172, Child safety.
-

co
co
.... N
" N .... 0
00
<..:l 'SI"
Tether anchors and tether straps
Fig. 174 Te the r ancho rs: att achm ent hook locatio ns be­
hi nd the rea r seatbacks
The tether anchors for the two/three* re ar seat­
ing positions are located on the backside of the
rear seatbacks
¢ fig. 174. Vehicles with two rear
seating positions are equipped with two tether
anchors.
A tether is a straight or V-shaped strap that at ­
taches the top part of a child restraint to special
anchorage points in the vehicle.
The purpose of the tether is to red uce the for­
ward movement of the child restraint in a crash,
in order to he lp reduce the risk of head injury
that could be caused by striking the vehicle inte­ rior .
F orward facing child restraints manufactured af­
ter September 1, 1999, are required by U.S. fed­
eral regulations to comply with new child head movement performance requirements . These
new performance requirements make a tether
necessary on most new child safety seats .
A WARNING
Improper installation of child restraints will
increase the risk of injury and death in a
crash.
- Always follow the instructions provided by
the manufacturer of the child restra int you
intend to install in your Aud i.
- Improper use of child restra int anchors (in­
cl uding tethe r anchors) ca n l ead to inj ury in
a collision. The anchors are designed to
withstand only those lo ads imposed by cor­
rectly f itted child restraints .
Child sa fety
- Never mount two child restraint systems on
one LATCH lower anchor point.
- Never attach two child restraint systems to
one tether strap or tether anchorage.
- Never attach a tether strap to a tie-down
hook in the luggage compa rtment.
- Never use child restraint tether anchorages to secure safety be lts or other kinds of occu­
pant restraints.
- Never secure or attach any luggage or other
items to the LATCH lower anchorages or to
the tether anchors.
- If you must install a rearward facing child
safety seat on the front passenger seat be­
cause of exceptional circumstances and the
PAS SENGER AIR BAG OFF light does not
come on and stay on, immediately install
the rea r-facing child safety seat in a rear
seating position and have the a irbag system
i n spe cted by your Audi dea ler.
Installing the upper tether strap on the
anchorage
F ig . 1 75 Tet her st rap: p roper rout ing an d mount ing
Installing the tether strap
.,. Release or deploy the tether strap on the child
restraint according to the ch ild rest raint manu­
facture r's instr uctions .
.,. Guide the upper te ther s trap under or s ideways
of the rear head restraint~
fig. 175 (dependi ng
on the chi ld restraint).
.. Attach the tether strap anchorage hook into
the tether anchorage.
.,. Pull on the tether strap hook so that the spring
catch of the hook engages .
.,. Tighten the tether strap firmly following the
child restra int manufacture r's instructions . .,.
189

co co .... N
" N .... 0
00
\.J - A WARNING ,~
Ad Blue can irritate the skin, eyes and respira­
tory system. If there is contact with the fluid,
flush immediately with plenty of water . Con­
sult a physician if necessary.
CD Note
- Only use Ad Blue that conforms to the
standard ISO 22241 -1. Do not mix any addi ­
tives w ith the AdBlue and do not d ilute it
with water.
- Do not add Ad Blue to the diesel ta nk or add
diesel fuel to the Ad Blue tank. Do not start
the engine under any circumstances if the
wrong f uel is filled in the tank. There is a
risk of damaging the fuel tank system and
the engine. See an author ized Audi dealer or
authorized Audi Service Facility for ass is­
tance .
- Ad B lue attacks surfaces such as pa inted ve ­
hicle components, plast ic and carpet . Re­
move the fluid as quickly as poss ible with a
damp cloth and plenty of cold water. If the
Ad Blue has already crysta llized, use warm
water and a sponge . AdBlue residue that is
not removed will crysta llize a nd can damage
the affected surface.
- Do not store refill bottles or canisters per ­
mane ntly in the vehicle . If the container
l ea ks, the escaping AdBl ue could damage
t h e veh icle inter io r.
- Do not allow AdBlue to come into co ntact
with clothing. If there is contact w ith the
f lui d, f lush immed iate ly w ith p lenty of wa­
te r.
(j) Tips
Follow the Ad B lue man ufact urer's instr uc­
t ions fo r use and storage.
Refilling AdBlue using a bottle
Applies to: vehicles with selective catalytic reduction
.. Remove the cap from the refi ll bottle ¢ A in
Filling AdBlue on page 197, ¢(Din Filling
AdBlue on page 197 .
Check ing and Filling
.. Position the bott le on the fi ller tube and turn
the bottle clockwise until it stops turning .
.. Press lightly against the bottom of the bottle
to empty it. Cont inue pressing the bottom of
the bottle until it is empty or until fluid stops
flow ing into the tank .
.,. Remove the bottle and seal the filler neck
¢ page 198, Completing AdBlue refill.
CD Note
Only use refill bottles that are approved for
your vehicle . Using other systems can cause
Ad B lue to leak.
@ Tips
- You can obtain ref ill bottles from an author­
ized Aud i dea le r o r aut horized Aud i Serv ice
Facility.
- A permitted refi ll bottle contains approxi­
mately 0.5 gallon (1.9 liters) of AdBl ue.
Refilling AdBlue using a canister
Applies to: vehicles with selective catalytic reduction
®
+®
Fig. 181 Can iste r w ith attachable hose
.. Remove the cover from the refill canister¢ A
in Filling AdBlue on page 197, ¢(Din Filling
AdBlue on page 197 .
.,. Secure the end of the hose (Don the opening in
t he caniste r@ by turni ng the hose to the right.
.,. Remove the cap @ from the o ther end of the
hose @.
.. Position the end of the hose @ on the filler
neck in the veh icle and turn the hose to the
r ight to tighten it .
.. Lift the canister up and then t ip it. Cont inue
holding the canister in a tipped pos ition until it ..,.
197

co
co
.... N
" N .... 0
00
<..:l 'SI"
Opening/closing the hood
The hood is released from inside the vehicle.
Fig. 1 82 D rive r footwell: release lever
Fi g. 1 83 Roc ke r sw itc h under the hood
M ake sure the w iper arms a re not raised up from
the windshield . Otherwise the pa int could be
damaged .
Opening the engine compartment lid .. Wi th the driver's doo r open, pu ll the leve r be­
low the instrument panel in the direct ion of the
arrow c>fig.182 .
Checking and Filling
.. Raise the hood slightly c> ,& .
.. Press the rocker switch under the hood upward
¢fig. 183. This releases the catch .
.. Open the hood .
Closing the engin e compartm ent lid
.. Push the hood down until yo u over ride the
force of the strut .
.. Let the hood fall lightly into the latch.
Do not
press it in.
c> ,&.
A WARNING
-
-Never open the hood when there is steam or
coolant escaping from the engine compart­
ment, because there is a risk that you could
be burned. Wait unt il no steam or coolant is
escaping.
- For safety reasons, the hood m ust always be
closed securely while driv ing . Because of
this, a lways check t he hood afte r closing i t
t o make sure it is latched correct ly . T he
hood is latched if the front corners cannot
be lifted.
- If you no tice that t he hood is not latched
while you are d riving, stop immed iately and
close it, because driving when the hood is
not latched increases the risk of an accident .
201

Check ing and F illing
The coolant leve l is monitored through the. in­
dicator light ¢
page 14. However, we do recom­
mend occasionally check ing the coo lant level
manually.
I f you must add coolant, use a mixture of water
and coolant additive. Mixing the coolant additive
with d istilled water is recommended.
Coolant additiv e
The coolant addi tive is made of anti-freezi ng and
corros ion protection agents. Only use the fo llow­
ing coolant additives . These additives may be
mixed with each other.
Coolant additive Specification
Gl3 TL 774)
Gl2++
TL 774 G
The amount of coolant add itive that needs to be
mixed w ith water depends on the climate where
the vehicle will be operated. If the coolant addi­
tive percentage is too low, the coolant can freeze
a nd damage the engine.
Coolant
Freeze protec·
additive tion
Warm reg ions min. 40% m in. -13 ° F
max. 45% (-25 °C)
Cold regions min. 50% max . -40 °F
max . 55% (-40 °C)
([)
Note
-Before the start of winter, have your author­
ized Audi dealer or authorized A udi Se rvice
Fac ility check if the coolant additive in you r
vehicle matches the percentage approp riate
fo r the clim ate. Thi s is especially important
when driving in co lder climates .
- If the approp riate coolant additive is not
available in an emergen cy, do no t add any
other additive. You cou ld damage the en ­
gine. If this happens, only use water and re­ store the correct mixture ratio with the
spec ified coolant additive as soon as possi­
ble.
- Only refill with new coo lant.
- Radiator sealant must not be mixed w ith
the coo lant .
206
· Adding coolant
F ig. 186 En gin e compartment : coolant exp ansion tank
cover
-N
-~
~
Observe the safety precautions ~ .&. in Working
in the engine compartment on page 199.
Check ing the engin e coolant level
Park the vehicle on a leve l surface.
.,. Switch the ignit ion off.
.,. Read the coolant level on the coolant expansion
tank ¢
page 202, fig . 184. The coolant level
must be betwee n the MIN and MAX mark ings
when the e ngine in co ld. When the engine is
wa rm it c an be slightly above the MAX marking.
Adding coolant
Requirement: there must be a residual amount of
coolant in the expansion tank ¢(D .
.,. Let the engine cool down .
.,. Place a cloth over the coolant expansion tank
cap and unscrew the cap counterclockw ise
¢ .8_ .
.,. Add coo lant m ixed in the correct rat io
¢ page 205 up to t he MAX mar king.
.,. Make sure that the f luid level remains stab le.
Add mo re coolant if necessary.
.,. Close the cap securely .
Coolant loss usually ind icates there is a lea k. Im­
med iate ly dr ive your vehi cle to a n author ized
Audi dealer or author ized A udi Service Fac ility
and have the cooling system inspected . If the
cooling system is not leaking, a loss can come
from the coolant boiling through overheating
and being pushed out of the cooling system.

Emerg ency assis ta nce
Emergency assistance
General information
... Park the vehicle as far as possible from moving
traffic in the event of a breakdown. In the event
of a flat tire, park the vehicle on a level surface .
It you are on a steep hill, be especially careful.
.,. Set the parking brake .
.,. Switch the emergency flashers on .
... Set up the warning triangle
r=;,page 240 .
... Have the passengers exit the vehicle . They
should move to a safe place, for example be­
hind a guard rail.
A WARNING
Follow the steps given above. This is for your
protection and the for the safety of other driv­
ers.
Equipment
Warning triangle
A ppl ies to: ve hicles w ith warning triangle
Fig. 196 Luggage compartment lid : wa rnin g triangle
The warning triangle placed in the vehicle at the
factory is located in the luggage compartment.
... Turn the twist lock
r::;, fig. 196 and pull the cover
downward to open the cover .
.,. Remove the warning triangle from its holder.
The luggage compartment lid is only designed to
hold the warning triangle offered by the Audi
Genuine Accessories program.
240
Vehicle tool kit
Fig. 197 Luggage compartment: vehicle tool kit, tire mob i­
lity kit and comp ressor
The vehicle tool kit, vehicle jack*, tire mobility
kit* and compressor are stored in the luggage
compartment under the cargo floor cover.
.,. Lift the cargo floor by the plastic handle .
.,. Tu rn the handle counter-clockwise and remove
the cover or the spare ti re*.
A WARNING
Improper use of the vehicle jack can cause se­
rious personal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot
attain the necessary tightening torque if you
use the hex head, potentially causing an ac­
cident.
- The factory-supplied jack is intended only
for your vehicle model. Under no circum­ stances should it be used to lift heavy
veh icles or other loads; you risk injuring
yourself.
- Never start the engine when the veh icle is
raised, which could cause an accident.
- Support the vehicle securely with a ppropri­
ate stands if work is to be performed under­
neath the vehicle; otherwise, there is a po­
tential risk for injury .
- Never use the jack supplied with your Aud i
on another vehicle, particularly on a heavier
one. The jack is only suitable for use on the
veh icle i t came with.
¢j) Tips
The vehicle jack* in your vehicle is mainte­
nance-free.

Emerg ency assis ta nce
• Align the jack so that its arm @ c::> fig. 205 en­
gages in the designated lifting point in the door
s ill and the movable base ® lies flat on the
ground. The base ® must be
vertical under the
lifting point @.
• Wind the jack up further until the flat tire
comes off the ground
c::> ,&. .
Position the vehicle jack on ly unde r the designat­
ed lifting points on the sill
c::> fig . 204 . There is ex­
actly
one locat ion for each wheel. The jack must
not be positioned at any other location
c::> .&. c::>0.
An unst able s urfa ce under the jack can cause the
ve hicle to slip off the jack . Always provide a firm
base for the jack on the ground . If necessary
p lace a sturdy boa rd or simi lar support under the
jack . On
h ard, slipp ery su rface s (such as tiles)
use a rubbe r mat or similar to prevent the jack
from sl ipping
c::> .&. .
& WARNING
- Yo u or your passengers could be injured
whi le changing a wheel if you do not follow
these safety precautions:
- Position the veh icle jack only at the desig­
nated lifting points and align the jack .
Othe rw ise, the vehicle jack cou ld slip and
cause an injury if i t does not have suffi­
cient hold on the vehicle.
- A soft or unstable s urface unde r the jack
may cause the vehicle to slip off the jack.
A lways provide a firm base for the jack on
the ground. If necessary, use a sturdy
board under the jack .
- On hard, s lippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slipping.
- To help prevent injury to yourself and your
passenge rs:
- Do not raise the vehicle unt il you are sure
the jack is securely engaged .
- Passengers must not remain in the vehicle
when it is jacked up.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traff ic.
246
- Make sure jack position is correct, adjust
as necessary and then continue to ra ise
the jack .
- Changes in temperature or load can affect
the height of the veh icle.
(D Note
Do not lift the vehicle by the si ll. Position the
vehicle jack only at the des ignated lift ing
points on the sill. Otherwise, your vehicle will
be damaged.
(D Tips
The vehicle jack mode * switches off automati­
cally at speeds above 6 mph (10 km/h).
Removing and installing the sill extension
cover
App lies to: vehicles with sill extension
Fig . 206 S ill: rem ovin g the cover
• Pull the cover down to remove it. c::> fig. 206
• To install the cover, insert it in the mount and
pre ss it upward until it clicks into place . The
cover must be flush with the surface of the sill
extens ion .
@ Tips
Some models may also have a cover for the
rear veh icle lift point .

Emergency assistance
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right direction .
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spare t ire with a tread pattern in­
tended for use in a specific direction, please note
the following:
- The direction of rotation is marked by an arrow
on the side of the tire.
- If the spare tire has to be installed in the incor­
rect direction, use the spare tire only tempora­
rily since the tire will not be able to achieve its
optimum performance characteristics with re­
gard to aquaplaning, noise and wear.
- We recommend that you pay particular atten­
tion to this fact during wet weather and that
you adjust your speed to match road condi­
tions.
- Replace the flat tire with a new one and have it
installed on your vehicle as soon as possible to
restore the handling advantages of a unidirec­
tional tire.
Notes on wheel changing
Please read the information q page 218, New
tires or wheels
if you are going to use a spare tire
which is different from the tires on your vehicle.
After you change a tire:
- Check the tire pressure on the spare tire im­
mediately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos­
sible by your authorized Audi dealer or a
qualified service station.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of 90
ft lb
(120 Nm).
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire ,
they should be replaced before you check the
tightening torque.
248
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi­
ble. Remount the wheel cover.
Until then , drive with extra care and at reduced
speeds.
~ WARNING
- If you are going to equip yo ur vehicle with
tires or rims which differ from those which
were factory installed, then be sure to read
the information
q page 218, New tires or
wheels.
- Always make sure the damaged wheel or
even a flat tire and the jack and tool kit are
properly secured in the luggage compart­
ment and are not loose in the passenger
compartment.
- In an accident or sudden maneuver they
could fly forward, injuring anyone in the ve­
hicle.
- Always stor e damaged wheel, jack and tools
secure ly in the luggage compartment. Oth­
erwise, in an accident or sudden maneuver
they could fly forward, causing injury to pas­
sengers in the vehicle.
Spare tire
Space-saving spare tire
App lies to: vehicles wit h spare tire
Fig. 209 Luggage compartment: space -saving spare t ire
The spare tire is intended for short-term use on-
-
ly. Have the damaged tire checked and, if neces­
sary, replaced by an authorized Audi dealer or au­
thorized Audi Service Facility as soon as possible . .,..