2017 AUDI A7 fuel

Checking and Filling
-Do not remove the engine cover under any
circumstances . This increases the risk of
burns.
- If tests need to be performed with the en­
gine running, there is additional danger due
to moving components (such as the ribbed belt, alternator and radiator fan) and from
the high voltage ignition system.
- Do not under any circumstances give gas in­
advertently (for example, by hand from the
engine compartment) if the vehicle is sta­
tionary but the engine is running and a gear
is engaged. Otherwise, the vehicle will start
to move immediately and this could result
in an accident.
- Pay attention to the following warnings list­
ed when work on the fuel system or on the
electrical equipment is required.
- Do not smoke .
- Never work near open flames.
- Always have a working fire extinguisher
nearby
- All work on the battery or electrical system
in your vehicle can result in injuries, chemi·
cal burns, accidents or burns. Because of
this, all work must be performed
only by an
authorized Audi dealer or authorized Audi
Service Facility.
- To reduce the risk of electric shock and in­
jury, never touch the following components when the engine is running or is being start­
ed :
- Ignition cable
- Other components in the electronic high-
voltage ignition system
-If you must check or perform work on the
engine while it is running:
- Set the parking brake and place the selec­
tor lever in the P (park) position first .
- Always proceed with extreme caution so
that clothing, jewelry or long hair do not
become caught in the radiator fan, fan
belt or other moving components or do
not come into contact with hot compo­
nents. Tie back long hair before beginning
work and do not wear clothing that can
hang down into the engine.
200
-Limit your exposure to exhaust and chemi­
cals to as short a time as possible
c> A .
A WARNING
California Proposition 65 Warning:
- Engine exhaust, some of its constituents,
and certain vehicle components contain or
emit chemicals known to the State of Cali­
fornia to cause cancer and birth defects and
reproductive harm . In addition, certain flu­
ids contained in vehicles and certain prod­
ucts of component wear contain or emit
chemicals known to the State of California
to cause cancer and birth defects or other
reproductive harm.
- Battery posts, terminals and related acces­
sories contain lead and lead compounds,
chemicals known to the State of California
to cause cancer and reproductive harms.
Wash hands after handling.
(D Note
When filling fluids, be sure not to mix the flu­
ids up. Otherwise severe malfunctions and en­
gine damage will occur.
@:) For the sake of the environment
You should regularly check the ground under
your vehicle in order to detect leaks quickly. If
there are visible spots from oil or other fluids, bring your vehicle to an authorized Audi deal­
er or authori zed Audi Service Facility to be
checked.

co
co
.... N
" N .... 0
00
\.J ' Using the proper engine oil is important for the
functionality and s ervice life of the engine. Your
engine was factory-filled with a high -quality oil
which can usually be used throughout the entire
yea r.
Note
Your Limited New Vehicle Warranty does not
cover damage or malfunctions d ue to failure
to follow rec ommended maintenance and use
requireme nts as s et forth in the Audi Owner's
Manual and Warranty & Maintenance booklet .
- Use only a high quality engine oi l that ex-
pressly complies with the Au di oil quality
standard specified for your vehicle's engine.
Using any o ther oil can cause serious engine
damage.
- Do not mix any lubricants o r other additives
into the engine oil. Doing so can cause en­
gine damage.
@ Tips
If you need to add oil and there is none availa­
ble that meets the Audi o il quality standard
your eng ine requ ires, you may add a total of
no more than 0 .5 qt (0.5 l) of a h igh-quali ty
"synthet ic"oil that meets the following speci ­
fications.
- Applies to: gaso line engine: ACEA A3 or
API SM with a viscosity grade of SAE OW-30,
SAE 5W-30 or SAE 5W-40.
- Applies to: diesel engine: ACEA C3 or API CF
with a viscosity grade of SAE OW-30 o r
SAE 5W-30 .
- For more information about engine oil that
has been approved for your vehicle, please
contact e ither your authori zed Audi dea ler
or Audi Customer Relat ions at
1 (800) 822-2834 or visit our web site at
www .audiusa .com or www .aud ica nada.ca.
Engine oil consumption
The engine in your vehicle depends on an ade­
quate amount of oil to lubricate and cool all of
its moving parts .
In order to provide effective lub rication and cool­
ing of in ternal engine componen ts, all internal
Ch eck ing and Filling
combustion engines consume a certain amo unt
of oil. Oil consumption vari es from engin e to en­
gine and may change s ignificantly over the life of
the engine . Typ ically, engines w ith a specified
break-in period (see¢
page 65) consume mo re
o il during the break -in per iod than they consume
after o il consumption has stab il ized .
Under normal cond itions, the rate of oil con ­
sump tion depends on the qu ality and viscos ity of
the oil, the RPM (revolutions per minute) at
wh ich the engine is operated, the amb ient tem­
perature and road co ndit ions. Further facto rs a re
the amount of oi l di lution from wate r condensa ­
tion or fuel resid ue and the oxidat ion level of the
o il. As any engine is subject to wear as mileage
builds up, the oil consumption may increase over
time unti l replac ement of worn components may
become necessary.
With a ll these variab les coming into play, no
standard rate of oil consumption can be estab ­
li sh ed or sp ecified . There is no alternative to reg­
u lar and frequent checking of the oi l level, see
Note .
If the yellow engine oil leve l warning symbo l in
the instr ument cluster
Ill lights up, yo u should
check the oi l level as soon as possible
¢
page 204. Top off the o il at your earliest con­
venience ¢
page 204 .
A WARNING
-Before you check anyt hing in the engine com -
partment, always read and heed all WARN­
INGS
¢ .&. in Working in the engine compart­
ment on page 199.
{(D Note
Driving w it h an insufficient oil level is likely to
cause severe damage to the eng ine .
(D Tips
-The oil pressure wa rn ing display. is not
an indicator of the o il leve l. Do not rely on
i t . Instead, check th e oil level in your en­
gine at regular interval s, preferably each
time you refuel, and alway s before going
on a long trip .
203

a)
a)
.--< N
" N .... 0 a) 0.:,
"'
Wheels
Wheels and Tires
General information
.,.Check your tires regularly for
damage (punctures, cuts, cracks
and bulges). Remove foreign ob­
jects from the tire tread.
.,. If driving over curbs or similar
obstacles, drive slowly and ap­
proach the curb at an angle.
.,.Have faulty tires or rims re­
placed immediately.
"'Protect your tires from oil,
grease and fuel.
.,.M ark tires before removing
them so that the same running
direction can be maintained if
they are reinstalled.
"'Lay tires flat when storing and
store them in a cool, dry location
with as little exposure to light as
possible.
(D Note
-Please note that summer and
winter tires are designed for
the conditions that are typical in those seasons. Audi recom­
mends using winter tires dur­
ing the winter months. Low
temperatures significantly de­ crease the elasticity of summ­
er tires, which affects traction
Wheels
and braking ability. If summer
tires are used in very cold
temperatures, cracks can form
on the tread bars, resulting in
permanent tire damage that
can cause loud driving noise
and unbalanced tires.
-Burnished, polished or
chromed rims must not be
used in winter driving condi­
tions. The surface of the rims
does not have sufficient corro­
sion protection for this and
could be permanently dam­ aged by road salt or similar
substances.
Tire designations
Fig. 190 T ir e designations on the side -
wall Ill>
211

Wheel s
Bead separation
means a breakdown of the bond
between components in the bead .
Cord
means the strands forming the
plies in the tire.
Cold tire inflation pressure
means the tire pressure recom­
mended by the vehicle manufac­
turer for a tire of a designated
size that has not been driven for more than a couple of miles (kilo­
meters) at low speeds in the
three hour period before the tire
pressure is measured or adjusted.
Curb weight
means the weight of a motor ve­
hicle with standard equipment in­
cluding the maximum capacity of
fuel, oil, and coolant, air condi­
tioning and additional weight of
optional equipment.
E x tra load tire
means a tire designed to operate
at higher loads and at higher in­
flation pressures than the corre­ sponding standard tire . Extra load
tires may be identified as "XL",
"xl", "EXTRA LOAD", or "RF" on
the sidewal l.
214
Gross Axle Weight Rating
("GAWR ")
means the load-carrying capacity
of a single axle system, measured
at the tire -ground interfaces .
Gross Vehicle Weight Rating
(" GVWR ")
means the maximum total loaded
weight of the vehicle .
Groove
means the space between two ad­
jacent tread ribs .
Load rating (code )
means the maximum load that a
tire is rated to carry for a given in ­
flation pressure. You may not find
this information on all tires be­
cause it is not required by law.
Ma ximum load rating
means the load rating for a tire at
the maximum permissible infla­ tion pressure for that tire.
Ma ximum loaded vehicle
weight
means the sum of :
(a) Curb weight
(b) Accessory weight
(c) Vehicle capacity weight, and
(d) Production options we ight

Wheels
and follow the important safe­
ty precautions in
q page 224,
Tires and vehicle load limits.
-The tire must flex more if the
tire pressure is too low or if
the vehicle speed or load are
too high. This heats the tire up
too much. This increases the
risk of an accident because it
can cause the tire to burst and
result in loss of vehicle con­
trol.
-Incorrect tire pressure in­
creases tire wear and has a
negative effect on driving and
Tire pressure table
Please note that the information
contained in the following table
was correct at the time of print­ ing, and the information is sub­
ject to change. If there are differ­
ences between this information
and the tire pressures specified
on the label on the driver's side B­
pillar, always follow the specifica ­
tion on the B-pillar label
q page 221, fig. 192.
222
braking behavior, which in­
creases the risk of an accident.
(D Note
Replace lost valve caps to re­
duce the risk of damage to the
tire valves.
@ For the sake of the environment
Tire pressure that is too low in­
creases fuel consumption.
(D Tips
Audi recommends using the
tire pressure specified for a
normal load
q table on
page 223
or for a full load
when the vehicle is partially
loaded.
Make sure that the tire designa­
tion on your tire matches the des­
ignation on the tire pressure label
and the tire pressure table.
The following table lists recom­
mended tire pressures in cold
tires according to the load and
the size of the tires installed.

Wheels
Model/ Tire designation Tire pressure
Engine Normal load Maximum load
(up to 2/3* people)a>
front rear front rear
PSI kPA PSI kPA
PSI kPA PSI kPA
RS 7 275/35 ZR20 102Y
Sportback:
36 250 30 210 39 270
39 270
High Performance
4.0 L 275/30 ZR21 98Y
41 280 38 260 45 3 10 4 5 310
8-cylinder
High Performance
RS 7 275/30 ZR21 98Y
Sportback
perform- High Performance
ance:
46 320 44
300 51 350 51 350
4.0 L
8-cylinder
a) Vehicles with 4 seating positions: t wo people i n the front, Vehicles with 5 seating
positions:
two peop le in t he front , one pe rson in the re ar
A WARNING
Please note the important safe­
ty precautions regarding tire pressure ¢
page 221 and load
limits¢
page 224.
Tires and vehicle load limits
There are limits to the amount of
load or weight that any vehicle
and any tire can carry. A vehicle
that is overloaded will not handle
well and is more difficult to stop.
Overloading can not only lead to
loss of vehicle control, but can al­
so damage important parts of the
vehicle and can lead to sudden
224
tire failure, including a blowout
and sudden deflation that can
cause the vehicle to crash.
Your safety and that of your pas­
sengers also depends on making
sure that load limits are not ex­
ceeded. Vehicle load includes ev­
erybody and everything in and on
the vehicle. These load limits are
technically referred to as the vehi­
cle's
Gross Vehicle Weight Rat­
ing
("GVWR").
The "GVWR" includes the weight
of the basic vehicle, all factory in­
stalled accessories, a full tank of
fuel, oil, coolant and other fluids
111-

Wheels
As an added safety feature, your vehicle has been
equipped with a tire pressure mon itor ing system
(TPMS) that illuminates a low tire pressure tell­
tale when one or more of your tires is significant­
ly under-inflated . Accordingly, when the low tire
pressure telltale illuminates, you should stop and
check your tires as soon as possible, and inflate
them to the proper pressure . Driving on a signifi­
cantly under-inflated tire causes the tire to over­
heat and can lead to tire failure. Under-inflation
also reduces fuel efficiency and ti re tread life,
and may affect the vehicle's handling and stop­
ping ability.
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsibility to maintain correct tire pressure,
even if under- inflation has not reached the level
to trigger illumination of the TPMS low tire pres­
sure telltale.
Your vehicle has also been equipped with a TPMS
malfunction indicator to indicate when the sys­
tem is not operating properly. The TPMS mal­
function indicator is combined with the low tire
pressure telltale . When the system detects a
malfunction, the telltale will flash for approxi ­
mately one m inute and then remain cont inuously
illuminated . This sequence will continue upon
subsequent vehicle start-ups as long as the mal­
function exists .
When the malfunct ion indicator is illuminated,
the system may not be able to detect or signal
low tire pressure as intended. TPMS malfunctions
may occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly. Always check the
TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function
properly.
230
Tire pressure monitoring system
Applies to: vehicles with Tire Pressure Monitoring System in­
dicator
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction.
Fig. 194 Instrumen t cl uster : indicator l ig ht with me ssage
Using the ABS sensors, the tire pressure monitor­
ing system compares the tire tread circumfer­
ence and vibration characteristics of the individu­
al tires. If the pressure changes in one or more
tires, this is indicated in the instrument cluster
display with an indicator light
Rt] and a message.
If only one tire is affected, the location of that
tire will be indicated.
The tire pressures must be stored in the Infotain­
ment system again each time the pressures
change (switching between partial and full load
pressure) or after changing or replacing a tire on
your vehicle
¢ page 231. The tire pressure mon i­
toring system only monitors the tire pressure you have stored . Refer to the tire pressure label for
the recommended tire pressure for your vehicle
¢page 221, fig. 193.
Tire tread circumference and vibrat ion character­
istics can change and cause a tire pressure warn­
ing if :
- the tire pressure in one or more tires is too low.
- the tire has structural damage.
- the tire was replaced or the tire pressure was
changed and it was not stored¢
page 231 .
-the spare tire* is installed.
Indicator lights
RI]-Loss of pressure in at least one tire¢.&_ .
Check the tires and replace or repair if necessary . .,..

co
co
.... N
" N .... 0
00
\.J ' Care and cleaning
Component Situation Solution
Decorati ve parts /
Deposits Mild
soap solution al, a cleaning so lution suitable for stain-
less stee l, if necessary
trim
Paint
P aint damage Refer to the paint number on the vehicle data label, repair
with touch up paint
q page 260
Spilled fuel Rinse with water immediately
Surface rust Rust
remover, then protect with hard wax; for questions,
consult an authorized Audi dealer or authorized Audi Serv-
ice Facility.
Corrosion Have it removed by an authorized Aud i dealer or author-
ized Audi Se rvice Facility.
Water no longer Protect with hard wax (at least twice per year)
beads on the surface
of clean paint
No shine even though Treat with suitable polish; then app ly paint protectant if
paint has been pro -the polish that was used does not contain any protectant
tected/paint looks
poor
Deposits such as in - Dampen with water immediately and remove with a m icro-
sects, bird droppings,
fiber cloth
tree sap and road salt
Grease-based con- Remove immediately with a m ild soap solution al and a
taminants such as soft cloth
cosmetics or sunb lock
Carbon parts Deposits clean the same way as painted parts q page 235
a} Mi
ld soap solution: maximum two tab lespoons of neutral soap in 1 quart (1 lite r) of water
Interior cleaning
Component Situation Solution
Windows
Deposits Glass cleaner, then wipe dry
Decorative parts/ Deposits Mild
soap solutional
trim
Plastic parts
Deposits Damp cloth
Heavier deposits Mild soap solution al, detergent-free plastic cleaning solu-
tion, if necessary
Display s Deposits Soft cloth with LCD cleaner
Controls Deposits Soft brush, then a soft cloth with a m ild soap solutional
Safety belts Deposits Mild
soap so lution al, allow to dry before letting them re-
tract
237