2017 AUDI A7 service

Turn off ignit ion before lea ving vehi cle. Batte ry
i s di schar ging
This message appea rs if the driver's door is
opened while the ignition is sw itched on . Always
switch off the ignition if you are leaving the vehi­
cle. Also see
9 page 73.
Shift to P and turn off i gnition b efore l eaving
ca r, otherwi se vehicle can roll aw ay
This message appears if the driver's door is
opened while the igni tion is sw itched on and the
selecto r lever is not in t he P posit ion. Move the
selecto r lever in to the P pos ition and switch the
ignit ion off when you exit the vehicle. Otherwise
the vehicle could roll. A lso see
9 page 73 .
Starting the engine when there is a
malfunction
It may not be possible to start the engine under
certain circumstances, for example if the battery
in the vehicle key is drained, if interference is af­
fected the key or if there is a system malfunc­ tion .
Fig. 77 Center console/remote control key : starting the
engine if there is a malfunctio n
Requirement: the message Key is not r ecog ­
nized . Hold ba ck of key again st mark ed area .
See owner 's manual
must appear and the DJ in­
d icator light mus t turn on.
• Hold the remote control key in the location in­
dicated as shown in the illustrat ion
f >l) c::> fig . 77 .
• Press the b rake pedal.
• Press the
I START ENGINE STOPI button. The
~ engi ne will s tart .
.... N
" N .... 0
00
~ ll Market -specific
Drivi ng
• Drive to an authorized Audi dea ler or author ­
ized Audi Service Facility immediately to have
the malfunction corrected.
@ Tips
You can view the message again by pressing
the
I START ENGINE STOP I button.
Start-Stop system
Description
Applies to: veh icles w ith Start/Stop system
T he Sta rt/Stop system can help increase fue l
eco nomy and reduce CO2 emissions.
In Start/Stop mode, the engine shuts off auto­
matically when the vehicle is stopped, such as at
a traffic ligh t. The ignition rema ins switched o n
dur ing this stop phase. The engine w ill restart
automat ica lly when needed.
Applies to A7 Sportback: the Start/Stop system
activates automatically once the ignit ion is
switched on.
Applies to 57 Sportback: the last Start/Stop sys­
tem setting is restored when the ignit ion is
switched on.
Ba sic requirements for Start /Stop m ode
- The driver's door must be closed .
- The driver's seat belt much be fastened.
- The hood must be closed.
- The vehicle must have dr iven faster than
2.5 mph (4 km/h) since the last time it stop­
ped .
- A trailer must not be hitched to the vehicle.
(D Note
A lways swi tch the Sta rt/S top sys tem off when
driv ing th ro ugh wa ter
c::> page 71.
© Tips
The engine stops short ly before the ve hicle
comes to a s top
l) .
71

co
co
.... N
" N .... 0
00
<..:l 'SI'
-The vehicle battery charge leve l is too low .
- Power consumpt ion is high .
The engine can turn off again when the condi­
tions fo r Start-S top mode a re met .
Ignition i s switched off automatically
To prevent the veh icle battery from draining, the
ignit ion will sw itch off
automaticall y under the
following conditions :
- The vehicle must have already been driven.
- The Start/Stop system has stopped the engine.
- T he driver's door must be open.
- The driver's safe ty be lt must be unb uck led.
- The brake pedal must not be p ressed .
- The veh icle must be stationary .
In this case, the activated low beam is replaced by the parking light. The parking lights will
switch off after app roximately 30 minutes or
when yo u lock the vehicle .
If the Start/Stop system has not turned off the
engine or if you have sw itched the Start/Stop sys­
tem off manually, the ignition will not be auto­ mat ical ly switched off and the engine w ill contin ­
ue to run~&. .
A WARNING
To red uce the r isk of poisoning, never allow
t he engine to r un in conf ined s paces.
@ Tips
If you select the Dor N se lector lever position
after sh ifting into reverse, the vehicle m ust
be driven f ast er than 6 mph (10 km/ h) in or­
der fo r th e engine to switch off ag ain.
-
D rivi ng
Manually switching the Start/Stop system
off/on
Applies to : vehicles wit h Start/Stop sys te m
If you do not wish to use th e system, you can
switch it off manually.
Fi g. 79 Cen te r console: S tart/Stop system butto n
.. To switch the Start/Stop system off/on man­
ually, press the
l (A) ~ I button . The LED in the b ut­
ton turns on when the system is switched off.
(D Tips
If you switch the system off during a stop phase, the engine will start aga in automati­
cally .
Messages in the instrument cluster display
Applies to: vehicles wit h Start/Stop syste m
Start-stop system deactivated: Please re start
engine manually
T his message appears w hen spec ific conditions
are no t me t du ring a stop phase. The S tart/Stop
system will
not b e a ble to restart the engine . The
engine m ust be star ted with the
I S TAR T ENGINE S TOP ! button .
Start-stop system: Syst em fault! Currently
unavailable
T he re is a ma lfunction in the Start/Stop system.
Drive the vehicle to an a uth orized Aud i dea ler or
author ized Service Facility as soon as possible to
have the malfunction corrected .
73

co
co
.... N
" N .... 0
00
\.J ' During emergency braking, your vehicle will
brake similar to heavy braking. ESC and the
associated components (ABS, ASR, EDL)
cannot overcome the laws of physics . In cor­
ners and when road or weather conditions
are bad, a full brake application can cause
the vehicle to skid or the rear end to swerve,
which increases the risk of an accident.
- If the power supply fails, you cannot set the
parking brake if it is released. In this case,
park the vehicle on level ground and secure
it by placing the selector lever in the P posi­
tion. See an authorized Audi dealer or au­
thorized Audi Service Facility for assistance.
- Always take the vehicle key with you when leaving your vehicle, even for a short period
of time. This applies particularly when chil­
dren remain in the vehicle. Otherwise chil­
dren could start the engine, release the
parking brake or operate electrical equip­
ment such as power windows, which in­
creases the risk of an accident.
- No one should remain in the vehicle when it
is locked -especially children. Locked doors
make it more difficult for emergency work­
ers to get into the vehicle, which puts lives
at risk.
(D) Tips
When stopping at a traffic signal or stopping
in city traffic, you can set the parking brake
manually. The vehicle does not have to be
held with the brake pedal. The parking brake
eliminates the tendency to creep when a se­
lector lever position is engaged. As soon as
you press the accelerator pedal, the parking
brake releases automatically and your vehicle
starts to move
c::> page 75.
(D Tips
- Occasional noises when the parking brake is
set and released are normal and are not a
cause for concern.
- The parking brake goes through a self-test
cycle at regular intervals when the vehicle is
stopped. Any noises associated with this are normal.
Driving
- If there is a power failure, the parking brake
will not set if it is released, and it will not
release if it is set
c::> &. . See an authorized
Audi dealer or authorized Audi Service Fa­
cility for assistance.
Starting from a stop
Various convenience and safety functions may be
available when the vehicle begins driving, de­
pending on vehicle equipment .
Starting on hills with the parking brake set
Requirement: the driver's door must be closed
and the driver's safety belt must be fastened.
.,. To start driving comfortably when on a hill, set
the parking brake and begin driving as usual.
The braking force of the parking brake does not
release automatically until the wheels build up
enough driving force.
Starting on hills with hill hold assist
Hill hold assist makes it easier to start on hills.
Requirement: the driver's door must be closed
and the engine must be running.
.. To activate hill hold assist, press and hold the
brake pedal for several seconds. The vehicle
must be in an uphill direction of travel.
After releasing the brake pedal, the braking pow­ er is maintained for a brief moment
c::> ..&. to pre ­
vent the vehicle from rolling back when starting .
During this time, you can easily begin to move
your vehicle.
_& WARNING
A ppl ies to: ve hicles with hill hold assist
- If you do not begin driving immediately or
the engine stalls after releasing the brake
pedal, your vehicle may begin to roll back­
ward. Press the brake pedal or set the park­
ing brake immediately .
- The intelligent technology of hill hold assist
cannot overcome the limitations imposed by
natural physical laws. The increased comfort
offered by hill hold assist should not cause
you to take safety risks.
Ill-
75

-When accelerating using the la unch control
program, all vehicle parts are subject to
heavy loads . T hi s can lead to increased
wear.
Transmission malfunction
ml Tran smission : ple ase press b ra ke peda l and
s e le ct gear aga in
Press the brake pedal and se lect the desired se­
lector lever posit ion aga in. You can then continue
driving.
ml Transm ission o verheat ing : Please dri ve con­
ser vat ively .
The transm ission temperature has increased s ig ­
nificantly due to the sporty driving manner. D rive
in a less sporty manner until the temperature re­
turns to the normal range and the indicator light
switches of .
ml Transmission malfunction: You can continue
dri ving
There is a system malfunct ion in the transmis ­
sion . Yo u may continue driving. Drive to your au ­
thor ized Audi dealer or authorized Audi Service
F acility soon to have the ma lfunction corrected.
ml Transm ission m alfun ction: You can continue
dri ving with limited functionality
There is a system malfunction in the t ransm is­
sion . T he transmission is sw itching to emergency
mode. This mode only sh ifts in to certa in gears or
will no longer shift at all. The engine may stall. D rive to an authorized Audi dea ler or authorized
Aud i Service Facility immediately to have the
malfunct ion corrected.
Applies to: vehicles with S tronic transm ission
ml Ii) Tra nsm is sion malfunction : No reverse
gear. You can continue driving
There is a system malfunct ion in the transm is­
sion. The transmission is sw itchi ng to emergency
mode. This mode only shifts in to certa in gears or
will no longer shift at all. The engi ne may stall .
~ You cannot engage the reverse gear . Drive to an ....
~ author ized Audi dealer or author ized Audi Service N .... 0 co <.,;) 'SI"
D rivi ng
Facility immed iate ly to have the malfunction co r­
rected .
ml Transmiss ion malfunction : Stop vehi cle and
shift to park.
Do not continue dr iving. Se lect the P selector lev­
er posit ion and see an authorized Audi dealer or
authorized Aud i Serv ice Facility for ass istance .
(D Note
If the transm ission has switched to emergen­
cy mode, drive to your authorized Aud i dea ler
or authorized Audi Service Facility immediate­ l y to have the ma lfunction co rrected.
Selector lever emergency release
If the vehicle 's power supply fails, the selector
lever can be released in an emergency.
F ig . 85 Fro nt center conso le: eme rge ncy release for the se ­
lector leve r
... To reach the emergency release mechanism, re­
move the ashtray insert* .
... Loosen and remove the small cap in the asht ray
mou nt
Q fig . 85 .
... You now have a ccess to a pin. Using a screw­
driver or sim ila r object, press the pin down and
hold it in that position .
.,. Press the re lease button in the selector lever
and move it into the N position.
Only move the selec tor lever out of the P posit io n
whe n the ignition is switched on . If the veh icle
must be pushed or towed d ue to a power failure
(for example, the vehicle battery is drained), the
selector lever must first be moved to the N posi­
t ion using the eme rgency re lease mechanism.
81

Ass is t
The system cannot guarantee that it will detect
objects correctly and is switched off. The sensors
have been moved or are faulty. The pre sense
functions may also be affected. Dr ive to an au­
thor ized Audi dealer or authorized Audi Service
Facility immediately to have the malfunction cor ­
rected .
ACC: Currentl y unav ailabl e. No senso r vis ion
ACC and Audi braking guard : Curre ntly un avail­
a ble . No se nsor v ision
This message appea rs if the sensor view is ob­
s truc ted, for example by leaves, snow, heavy
spray or d irt. C lean the sensors ¢
page 89,
fig. 91.
ACC: Curre ntly unavailable. Gradient too steep
The road exceeds the max imum possible angle
for safe adapt ive cruise control operation . Adap­
tive c ruise contro l is switched off.
AC C: onl y availab le in D, S or M
Select the 0/5 or M selector lever position .
ACC: Currentl y unavailable . Parking brake ap •
pl ied
The adaptive c ruise contro l system switches off
automatically if the park ing bra ke is set.
ACC: Curre ntly unavail abl e. Stab ility control
( ESC) input .
This message appears if the Electronic Stabiliza­
tion Control (ESC) is tak ing action to stabilize the
ve hicle . In this case, adapt ive cruise control
sw itches off automatically.
AC C off: Manual control!
This message appears when adaptive cr uise con­
trol cannot set the parking brake . Press the brake
pedal to prevent the vehicle from rolling.
•••
Three white dots appear if a sett ing cannot be se­
lected wi th the ope rating lever. For example, this
h a ppens if adaptive c ruise cont ro l canno t start
driving automatically in stop -and-go traffic be­
cause the driver has not fastened their safety
be lt.
96
Door open
The adaptive cru ise cont rol system cannot switc h
o n when a door is open.
Stationary obj ect ah ead
This message appears if you wo uld like to switch
adaptive cruise control on and there is a station­
ary object or obstacle direct ly ahead of your vehi­
cle .
Audi active lane assist
Description
Appl ies to: vehicles with Audi act ive lane assist
Active lane assist detects lane marker lines with­
i n the lim its of the system using a camera in the
windshield. If you are approach ing a detected
lane marker line and it appears like ly that you
will leave the lane, the system w ill warn you with
corrective steering. You can override this steering
at any time. If you pass over a line, the steering
whee l w ill vibrate lightly. In orde r fo r thi s warn­
i ng vibration to occ ur, it must first be switched
on in the Infotainment system. Active lane ass ist
is ready for operation when the lane marker line
is detected on at least one side of the vehicle.
The system is des igned for driving on express­
ways and highways and therefore on ly activates
at speeds above approximately 40 mph (65 km/
h) .
Applies to: vehicles with side assist
If you activate a turn s ignal when act ive lane as­
s ist is ready and it classifies a lane change as crit ­
ica l because of vehicles traveling a longside you or
approach ing you, there wi ll be noticeable correc­
tive steer ing shortly before you leave the lane.
This will attempt to keep your veh icle in the lane.
Applies to: vehicles without side assist
The system will not wa rn you befo re c ross ing a
l ane marke r line if you have act ivated the t urn
s ignal. In this case, it assumes that you are
changing lanes intentionally.
Applies to: vehicles with adaptive cru ise control
The corrective steer ing is targeted based on the
driv ing situation . In add it ion to the lane marke r .,.

Ass is t
@ Tips
Make sure the camera's fie ld of view
¢
fig. 102 i s not obstructed by st ickers or any­
thing else. For information on cleaning, refer
to¢
page 235.
View in instrument cluster display
A ppl ies to: ve hicles w ith Audi active lane assist
Fig . 1 03 Instrument cl uster: act ive lane ass ist is sw itc hed
on a nd prov id ing warn ings
Fi g. 10 4 Inst rument cluster: act ive la ne assist is sw itc hed
on but not ready to provide warnings
You can call up the active lane assist display us­
ing the buttons in the multifunction steering
wheel ¢
page 21.
An addit iona l indicator appears in the Head -up
disp lay*.
White line(s) Active lane assist is activated and ready to p rov ide warnings.
Red line(s) Active lane assist warns you
(left or r ight) before leaving a lane
¢ fig. 103. In addit ion, the
steering wheel vibrates light ly.
Gray line(s) Active lane assist is activated,
b ut not ready to give warning
¢ fig . 104.
98
Messages in the instrument clu ster disp lay
If t he a ctive lane assist sw itches off automa tical­
l y, the indicator light in the display turns off and
one of the fo llow ing messages appears:
Audi a ctive lane assi st : Currentl y unavailable.
No camera v iew
This message appears if the camera is unable to
de tect the lines. This could happe n if:
- The camera field of view¢
page 97, fig. 102 is
dirty or covered in ice . Clean th is area on the
w indshield.
- The camera fie ld of view is fogged over. Wait
until the fog has cleared before switch ing the
active la ne assist on aga in .
- T he system has been unable to detect the lanes
for an extended p eriod of t ime due to road con­
ditions . Switch ac tive lane assist back on when
t he lines a re more visib le.
Audi a cti ve lane assi st: Currently unavailab le
There is a temporary act ive lane assist malfunc­
tion. Try switc hing the active lane assist on again
later.
Audi a cti ve l ane assist: System fault!
D rive to an au thor ized A udi dealer or au thorized
Audi Service Facility immediate ly to have the
malfunction corrected.
Audi active lane a ssis t : Plea se take over steering
This message appears if you are not steer ing by
yourself .
If this is the case, active lane assist does
not switch off, b ut it is "not ready" to provide a
warning. The system can help you keep the vehi­
cl e in the lane. However, you are responsible for
driv ing the vehicle and must steer it yourse lf .
Adjusting the vibration warning
App lies to: vehicles wit h Audi active la ne ass ist
.,. Select: the I CARI function button > (Car ) * Sys­
tems
contro l button > Dri ver assistan ce > Audi
a ct ive lane assist .
Vibrat ion warning
You can swi tch the addit io nal vib ra ti on war ning
in the steering whee l on or off .
Ill-

co
co
.... N
" N .... 0
00
<..:l 'SI"
-If vehicles are approaching or being l.eft
behind very quickly. The display may not
turn on in time.
- In poor weather conditions such as heavy
rain, snow or heavy mist.
- On very wide lanes, in tight curves, or if
there is a rise in the road surface. Vehicles
in the adjacent lane may not be detected
because they are outside of the sensor
range.
- Audi side assist cannot detect all vehicles
under all conditions, which can increase the
risk of accidents.
- Please note that side assist only displays ap­
proaching vehicles or vehicles in your blind
spot if your vehicle is traveling at least 19 mph (30 km/h).
- In certain situations, the system may not
work or its function may be limited . For ex­
ample:
- The display may not turn on at the right
time if vehicles are approaching or passing
very quickly.
- In poor weather conditions, such as heavy
rain, snow or fog.
- In very wide lanes, in tight curves or when
there are slopes in the roadway, vehicles
in the neighboring lanes may not be de­
tected because they are outside of the
sensor range .
(D Note
The sensors can be displaced by impacts or
damage to the bumper, wheel housing and
underbody. This can impair the system. Have
an authorized Audi dealer or authorized Audi
Service Facility check their function.
(D Ti ps
If the window glass in the driver's door or
front passenger's door has been tinted, the
display in the exterior mirror may be incor­
rect.
- For an explanation on conformity with the
FCC regulations in the United States and the
Industry Canada regulations, see
¢page 267.
Assist
Switching on and off
App lies to : vehicles wi th Audi side ass ist
Fig. 109 Driver 's door : side assist button
"' Press the button to switch the system on and
off ¢.&. in General information on page 100 .
The LED in the button turns on when side assist
is switched on.
Adjusting the display brightness
App lies to: vehicles wi th Audi side ass ist
The display brightness can be adjusted in the In­
fotainment system .
"' Select: the I CAR I function button > (Car)* Sys­
tems control button > Driver assistance > Audi
side assis t.
The display brightness adjusts automatically to
the brightness of the surroundings, both in the
information and in the warning stage. In very
dark or very bright surroundings, the automatic
adjustment will set the display to the minimum
or maximum level. In such cases, you may notice
no change when adjusting the brightness, or the
change may only be noticeable once the sur­
roundings change.
Adjust the brightness to a level where the display
in the information stage will not disrupt your
view ahead. If you change the brightness, the dis­
play in the exterior mirror will briefly show the
brightness level in the information stage. The
brightness of the warning stage is linked to the
brightness in the information stage and is adjust-
ed along with the information stage . ..,
101

Ass is t
@ Tips
- Side assist is not active whi le you are mak­
i ng the adjustment.
- Your settings are automatically stored and
assigned to the remote control key being
used.
Messages
Applies to: vehicles with Audi side assist
If side ass ist switches off by itself, the LED in the
button turns off and a message will appear in the
instrument cluster display:
Audi s ide assi st: Curr ently un availabl e. No
s enso r vi sion
The radar sensor vis ion is impaired. Do not cover
the area in front of the sensors with bike wheels,
stickers, dirt or other objects . Clean the area in
front of the sensors, if necessary ¢
page 100,
fig . 108.
Aud i side as sist: Currently un avail able
Side assist cannot be switched on at th is time be ­
cause there is a malfunction (for example, the
battery charge level may be too low).
Aud i side a ssist: S ys tem fault!
The system cannot guarantee that it will detect
vehicles correctly and it has switched off. The
sensors have been moved or are faulty . H ave the
system checked by an authorized Audi dealer or
authorized Audi Service Facility soon .
Audi side assi st : Unav ailable wh en towing
Side assist switches off automatically when a fac­
tory-installed trailer hitch is connected to the
electrical connector on the trailer. There is no
guarantee the system will switch off when using
a retrofitted tra iler hitch. Do not use side ass ist
when towing a trailer.
102
Night vision assist with
pedestrian and wild
animal detection
Description
Applies to : vehicles with night vision assist
The night vision assist con detect, highlight and,
if necessary, warn about pedestrians and large
wild animals.
Night vision assist with pedestrian and wild ani­
mal detection assists you at night by us ing an in­
frared camera to monitor the area in front of
your vehicle, within the limits of the system. It
can display objects up to a distance of approxi­
mately 1000 feet (300 m). The thermal image
detected by the camera is shown in the instru­
ment cluster disp lay. Warm areas appear lighter
and cold areas appear darker.
Highlighting detected pedestrians and wild
animals
Applies to: vehicles with n ight vis ion assist
Fig . 110 In stru men t cl ust er: yellow highlighted pedes ·
trians
Fig. 111 Instrument cl uster: symbol when the infrared im ­
age is not visible
Within the limits of the system, the night v is io n
ass ist can detect pedestr ians and wild animals ..,..