2017 AUDI A7 flat tire

co
co
.... N
" N .... 0
00
\.J - Check/correct the pressures of all four tires and
store the pressure again in the Infotainment sys­
tem
¢page 231.
ffim (T ire Pressure Monitoring System) T ire
pressu re : S ys tem malfunction !. If ffim
appears
after switching the ignition on or whi le driving
and the
[I] indicator light in the instrument clus­
ter blinks for approximate ly one minute and then
stays on, there is system malfunction. Try to
store the correct tire pressures¢
page 231. If
the ind icator light does turn off or turns on again
after a short period of time, dr ive to an author­
i zed A udi dealer o r authorized Audi Service Fac ili­
ty immediately to have the malfunc tion correct ­
ed .
& WARNING ,___ -
-If the tire pressure indicator appea rs in the
display, reduce your speed immed iate ly and
avoid any hard steer ing or braking maneu­
vers. Stop as soon as possib le and check the
t ires and their pressure.
- The driver is responsib le for maintaining the
correct tire pressure. You must check the
t ire pressure regu larly.
- Under certa in conditions (such as a sporty
driv ing style, winter cond itions or unpaved
roads), the tire p ressure monitoring system
indicator may be delayed.
{D) Tips
- The t ire pressure monitoring system can al­
so stop work ing when there is an ESC mal­
funct ion.
- Using snow chains may result in a system
malfunction .
- The t ire pressure monitoring system in your
Audi was calibrated with "Audi Orig inal
Tires"
¢ page 218. We recommend that you
use these t ires .
Wh eel s
Storing tire pressures
Applies to: vehicles with Tire Pressure Monitor ing System in­
dicator
If the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys­ tem.
.,. Make sure before storing that the tire pressures
of all four tires meet the specified values and
are adapted to the load
¢ page 221.
.,. Switch the ignit ion on.
.,. Select: the
I CAR ! funct ion button > ( C ar) * Sys­
tem s
contro l button > S ervic e & ch eck s> Tire
pres sure monitor > Store tire pre ssure > Yes,
s tore now .
(D Tips
Do not store the tire pressures if snow chains
a re installed.
Tire pressure monitoring
system
ill General notes
Each tire, including the spare (if provided),
shou ld be checked monthly whe n cold and inflat­
ed to the i nflat io n press ure recommended by the
vehicle manufacturer on the veh icle placard or
t ir e inflation pressure labe l. (If your ve hicle has
tires of a different size than the size indicated on
the vehicle placard or tire inflation pressure la­
bel, you should determ ine the proper tire infla­
t ion pressure for those tires).
As an added safety feature, yo ur vehicle has been
equipped with a tire pressure mon itor ing system
(TPMS) that illuminates a low tire pressure tell­
ta le when one or more of your tires is signif icant­
ly under-inflated. According ly, when the low t ire
pressure te lltale illum inates, you sho uld stop and
chec k your tires as soon as possib le, and inflate
t h em to the prope r pressure. Dr iving on a sig nifi­
ca nt ly unde r-inflated t ire causes the t ire to over ­
hea t and can lead to tire fa il ur e. Under-inflat ion
also reduces fue l effic iency and tire tread life,
and may affect the vehicle's handling and stop -
ping ability .
liJJ,-
231

Wheels
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsib ility to ma intain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire pres­
sure telltale.
Your veh icle has also been equ ipped with a TPMS
malfunction indicator to indicate when the sys ­
tem is not operating properly. The TPMS mal­
function indicator is combined with the low tire
pressure telltale . When the system detects a
malfunction, the telltale will flash for approxi­ mately one minute and then remain cont inuously
illum inated. This sequence will continue upon
subsequent vehicle start-ups as long as the mal­
function exists.
When the malfunct ion indicator is illuminated,
the system may not be able to detect or signal
low tire pressure as intended. TPMS ma lfunctions
may occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly . Always check the
TPMS malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure
that the replacement or alternate t ires and
wheels a llow the TPMS to continue to function
properly.
Description
A pp lies to: ve hicles w ith tire p ressure monitoring system
The tire pressure monitoring system monitors
the pressure in the four tires when driving.
The system uses sensors that measure the tem ­
perature and pressure in the tires . The data is
sent from these sensors to the contro l module by
radio frequency.
The Tire Pressure Monitoring System shows the current pressures and temperatures of the tir es
in the Infota inment system
c:> page 232. It also
compares the current t ire pressures with the
stored tire pressu res and gives a warning in the
d river information system if the tire pressure is
different from what is stored
r:';> page 233.
232
The system does not detect if the stored tire
pressures match the recommended tire pres­
sures. You must store the tire pressures again
c:> page 233:
-every time the tire pressures change, for exam ­
ple when the load in the vehicle changes,
- after replacing a tire, or
- if wheels with new whee l sensors are used.
_&. WARNING
- The tire pressure monitoring system assists
the driver in monitoring tire pressures. The
driver is responsib le for having the tires in­
flated to the correct pressure.
- Do not change the tire pressure when the
temperature of the tire is high. This could
result in serious damage to the tire and
even cause the tire to burst, increasing the
risk of an accident.
-A tire with low pressure flexes more. This heats the tire up too much. This could cause
the tread to separate and even cause the
tire to burst, increasing the risk of an acc i­
dent.
- The tire pressure monitoring system does
not warn about damage or defects in the
tire construct ion that could cause the tire to
burst, for examp le. Inspect your tires reg u­
larly.
(D Tips
- If tires are replaced, the sensors/valves do
not need to be removed or replaced. Just re­
placed the va lve stem and, if necessary, the
valve and the wheel electronics.
If you have
questions, see your authorized Audi dealer
or authorized Audi Service Facility.
- An incorrect display or a malfunction in the
tire pressure monitoring system can occur
after using the tire mobility kit. Have the
sensors rep laced by an authorized Audi
dealer or author ized Audi Service Facility.
Displaying tire pressures/temperatures
App lies to: vehicles wit h tire pressure monitoring syste m
Requirement: the ignition must be switched on . ...,

Emerg ency assis ta nce
Emergency assistance
General information
... Park the vehicle as far as possible from moving
traffic in the event of a breakdown. In the event
of a flat tire, park the vehicle on a level surface .
It you are on a steep hill, be especially careful.
.,. Set the parking brake .
.,. Switch the emergency flashers on .
... Set up the warning triangle
r=;,page 240 .
... Have the passengers exit the vehicle . They
should move to a safe place, for example be­
hind a guard rail.
A WARNING
Follow the steps given above. This is for your
protection and the for the safety of other driv­
ers.
Equipment
Warning triangle
A ppl ies to: ve hicles w ith warning triangle
Fig. 196 Luggage compartment lid : wa rnin g triangle
The warning triangle placed in the vehicle at the
factory is located in the luggage compartment.
... Turn the twist lock
r::;, fig. 196 and pull the cover
downward to open the cover .
.,. Remove the warning triangle from its holder.
The luggage compartment lid is only designed to
hold the warning triangle offered by the Audi
Genuine Accessories program.
240
Vehicle tool kit
Fig. 197 Luggage compartment: vehicle tool kit, tire mob i­
lity kit and comp ressor
The vehicle tool kit, vehicle jack*, tire mobility
kit* and compressor are stored in the luggage
compartment under the cargo floor cover.
.,. Lift the cargo floor by the plastic handle .
.,. Tu rn the handle counter-clockwise and remove
the cover or the spare ti re*.
A WARNING
Improper use of the vehicle jack can cause se­
rious personal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot
attain the necessary tightening torque if you
use the hex head, potentially causing an ac­
cident.
- The factory-supplied jack is intended only
for your vehicle model. Under no circum­ stances should it be used to lift heavy
veh icles or other loads; you risk injuring
yourself.
- Never start the engine when the veh icle is
raised, which could cause an accident.
- Support the vehicle securely with a ppropri­
ate stands if work is to be performed under­
neath the vehicle; otherwise, there is a po­
tential risk for injury .
- Never use the jack supplied with your Aud i
on another vehicle, particularly on a heavier
one. The jack is only suitable for use on the
veh icle i t came with.
¢j) Tips
The vehicle jack* in your vehicle is mainte­
nance-free.

Emergency assistance
Repairing tires
Applies to: vehicles w ith tire mob ility k it
Fig. 199 Components of the tire mobility kit
F ig. 200 Tire mobility k it connecti on
Requirement: the tire mobility kit must be laid
out and ready for use
o page 240.
Installing the tire mobility kit
.. Open the cover @on the compressor
¢fig. 199 .
.. Remove the connector@) and pressure hose®
with pressure gauge from the housing.
• Install the compressor pressure hose ® onto
the f lange @ on the tire sea lant bottle
(D .
.. Insert the sealant bottle with the flange at the
bottom into the opening @ on the compressor
cover.
.. Remove the valve cap from the fau lty tire.
.. Install the filler hose@) on the valve
0
ofig. 200 .
.. Connect the plug @¢ fig. 199 to a socket in
the vehicle.
.. Switch the ignition on.
Inflating a tire
.. Move the switch @ o fig. 200 on the compres­
sor into position
I.
242
.. Inflate the tire between 29 PSI and 36 PSI (2 .0
and 2.5 bar) and read the tire pressure on the
gauge .
.. If this tire pressure is not reached, remove the
filler hose. Drive slowly approximately 10 m
forward or in reverse so that the sealant can be
distr ibuted in the t ire. Pump up the tir e again
¢ _&. .
.&_ WARNING
-Read and follow the manufacturer's safety
precaut ions on the compressor and in the
instructions on the bottle of sea lant .
- If a tire pressure of 29 psi (2.0 bar) cannot
be reached after inflating for six minutes,
then the tire is too severely damaged. Do
not continue driving.
- If the tire cannot be repa ired with the tire
sealant, see an authorized Audi dealer or au­
thorized Audi Service Facility for assistance.
(D Tips
Do not operate the compressor for more than
six minutes continuously, or it can overheat.
Once the compressor has cooled, you can con­
tinue to use it.
Completing
App lies to : vehicles wit h tire mob ility kit
.. Adhere the sticker that says "max. 50 mph"
(80 km/h) that is provided with the tire mob ili­
ty kit within the driver's field of vision.
.. Stop the vehicle after driv ing for about 10 mi­
nutes and check the tir e pressure.
.. If the tire press ure is lower than 19 PSI (1.3
bar), then the tire is too severely damaged. Do
not continue driving .
.&_ WARNING
Pay attention to the following after repairing
the tire:
- Do not drive faster than 50 mph (80 km/h).
- Avoid hard acceleration, braking sharply,
and fast cornering .
- The vehicle may become more difficult to
control.

co
co
.... N
" N .... 0
00
\.J ' -If the tire is too severely damaged, see an
authorized Aud i dealer or authorized Audi
Service Facility for assistance.
@ For the sake of the environment
You can give the used tire sealant bottle to an
authorized Audi dealer or authorized A udi
Service Facility for disposal.
@ Tips
Remember to obtain a new bottle of sea lant
from an authorized Audi dea ler or authorized
Audi Service Facility after repairing a tire.
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel.
.. After you experience a tire failure, pull the car
well away from moving traffic and try to reach
level ground before you stop c::> &.,.
.. All passengers should leave the car and move
to a safe location (for instance, beh ind the
guardrai l) ¢ ,&. .
.. Engage the
parking brake to prevent your vehi­
cle from rolling unintentionally ¢,&. .
.. Move
selector lever to position P ¢ ,&. .
.. If you are towing a trailer, unhitch the trailer
from your vehicle .
.. Take the
jack and the spare tire* out of the lug­
gage compartment ¢
page 240.
.8, WARNING
You or your passengers could be injured while
changing a wheel if you do not follow these
safety precautions:
- If you have a flat tire, move a safe distance
off the road. Turn off the engine, turn the
emergency flashers on and use other warn­
ing devices to alert other motorists.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic.
Emergency assistance
- To help prevent the vehicle from moving
suddenly and possibly slipping off the jack,
always fully set the parking brake and block
the wheel diagonally opposite the wheel be­
ing changed . When one front wheel is lifted
off the ground, placing the Automatic
Transmission in P (Park) wi ll
not prevent the
veh icle from moving.
- Before you change a wheel, be sure the
ground is leve l and firm. If necessary, use a
sturdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­
pa rtment
¢page 135.
(D Tips
Before changing the wheel, you must activate
the jacking mode, so that the automatic con­
trols for the Adaptive Air Suspension* do not
make it more difficult to lift the vehicle with
the jack ¢
page 245 .
Changing a wheel
When you change a wheel, follow the sequence
described below step-by-step and in exactly that
order.
1. Activate the vehicle jack mode*¢ page 245.
2. Remove the decorative wheel cover* or the
wheel bolt caps*. For more details see also
¢ page 244, Decorative wheel covers or
¢ page 244, Wheels with wheel bolt caps .
3. Loosen the wheel bolts ¢page 245.
4. Locate the proper mounting point for the
jack and align the jack below that point
¢page 245.
5. Raise the car with the jack¢ page 245 .
6. Remove the wheel with the flat tire and then
install
the spare ¢ page 247.
7. Tighten all whee l bolts lightly.
8.
Lower the vehicle with the jack.
9. Use the wheel bolt wrench and
firmly tighten
all wheel bolts
c::>page 245.
10. Replace the decorative wheel cover* or the
wheel bolt caps*.
11. Deactivate the vehicle jack mode* in the
MMI:
I CARI funct ion button> (C ar )* systems .,.
243

Emergency assistance
control button > Servicing & checks > Air
susp.: jack mode> Off .
The vehicle jack mode* switches off automatical­
ly at speeds above 6 mph (10 km/h).
&_ WARNING
Always read and fo llow all WARNINGS and in­
formation ¢
.&. in Raising the vehicle on
page 246
and¢ page 248.
After changing a wheel
A wheel change is not complete without the do­
ing the following.
.. Always store the vehicle tool kit, the jack* and
the replaced tire in the luggage compartment
¢page 135.
.. Check the tire pressure on the spare wheel im­
med iately after mounting it.
.. As soon as possible, have the
tightening tor­
ques
on all wheel bolts checked with a torque
wrench. The correct tightening torque is
90 ft
lb (120 Nm).
.. Have the flat tire
replaced as soon as possible.
(D Tips
-If you notice that the wheel bolts are cor­
roded and difficu lt to t urn wh ile changing a
tire, they should be replaced before you
check the tightening torque.
- Drive at reduced speed until you have the
tightening torques checked.
- After changing a wheel, the tire pressure in
a ll four tires must be checked/corrected and
the tire pressure mon itor ing indicato r must
be stored in the MMI
¢page 231,
¢pa ge 233 .
244
Decorative wheel covers
Applies to: vehicles with decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts.
Fig. 201 Changing a whee l: Removing the whee l cover
Removing
.. Insert the hook (provided w ith the vehicle tool
kit) in the hole in the wheel hub cover.
.. Pull off the
decorative wheel cover ¢ fig. 201 .
Wheels with wheel bolt caps
Applies to: vehicles with wheel bolts with caps
The caps must be removed first from the wheel
bolts before the bolts can be unscrewed.
Fig. 202 Chang ing a wheel: remov ing the wheel bolt caps
Removing
.. Push the plastic clip (provided with the vehicle
tool kit) over the wheel bolt cap until the inne r
reta iners on the clip align with the edge of the
cover .
.. Remove the cap with the
plastic clip (vehicle
tool kit)
<:!> fig. 202.
Refitting
.. Place the caps over the wheel bolts and push
them back on.

Emerg ency assis ta nce
• Align the jack so that its arm @ c::> fig. 205 en­
gages in the designated lifting point in the door
s ill and the movable base ® lies flat on the
ground. The base ® must be
vertical under the
lifting point @.
• Wind the jack up further until the flat tire
comes off the ground
c::> ,&. .
Position the vehicle jack on ly unde r the designat­
ed lifting points on the sill
c::> fig . 204 . There is ex­
actly
one locat ion for each wheel. The jack must
not be positioned at any other location
c::> .&. c::>0.
An unst able s urfa ce under the jack can cause the
ve hicle to slip off the jack . Always provide a firm
base for the jack on the ground . If necessary
p lace a sturdy boa rd or simi lar support under the
jack . On
h ard, slipp ery su rface s (such as tiles)
use a rubbe r mat or similar to prevent the jack
from sl ipping
c::> .&. .
& WARNING
- Yo u or your passengers could be injured
whi le changing a wheel if you do not follow
these safety precautions:
- Position the veh icle jack only at the desig­
nated lifting points and align the jack .
Othe rw ise, the vehicle jack cou ld slip and
cause an injury if i t does not have suffi­
cient hold on the vehicle.
- A soft or unstable s urface unde r the jack
may cause the vehicle to slip off the jack.
A lways provide a firm base for the jack on
the ground. If necessary, use a sturdy
board under the jack .
- On hard, s lippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slipping.
- To help prevent injury to yourself and your
passenge rs:
- Do not raise the vehicle unt il you are sure
the jack is securely engaged .
- Passengers must not remain in the vehicle
when it is jacked up.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traff ic.
246
- Make sure jack position is correct, adjust
as necessary and then continue to ra ise
the jack .
- Changes in temperature or load can affect
the height of the veh icle.
(D Note
Do not lift the vehicle by the si ll. Position the
vehicle jack only at the des ignated lift ing
points on the sill. Otherwise, your vehicle will
be damaged.
(D Tips
The vehicle jack mode * switches off automati­
cally at speeds above 6 mph (10 km/h).
Removing and installing the sill extension
cover
App lies to: vehicles with sill extension
Fig . 206 S ill: rem ovin g the cover
• Pull the cover down to remove it. c::> fig. 206
• To install the cover, insert it in the mount and
pre ss it upward until it clicks into place . The
cover must be flush with the surface of the sill
extens ion .
@ Tips
Some models may also have a cover for the
rear veh icle lift point .

Emergency assistance
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right direction .
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spare t ire with a tread pattern in­
tended for use in a specific direction, please note
the following:
- The direction of rotation is marked by an arrow
on the side of the tire.
- If the spare tire has to be installed in the incor­
rect direction, use the spare tire only tempora­
rily since the tire will not be able to achieve its
optimum performance characteristics with re­
gard to aquaplaning, noise and wear.
- We recommend that you pay particular atten­
tion to this fact during wet weather and that
you adjust your speed to match road condi­
tions.
- Replace the flat tire with a new one and have it
installed on your vehicle as soon as possible to
restore the handling advantages of a unidirec­
tional tire.
Notes on wheel changing
Please read the information q page 218, New
tires or wheels
if you are going to use a spare tire
which is different from the tires on your vehicle.
After you change a tire:
- Check the tire pressure on the spare tire im­
mediately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos­
sible by your authorized Audi dealer or a
qualified service station.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of 90
ft lb
(120 Nm).
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire ,
they should be replaced before you check the
tightening torque.
248
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi­
ble. Remount the wheel cover.
Until then , drive with extra care and at reduced
speeds.
~ WARNING
- If you are going to equip yo ur vehicle with
tires or rims which differ from those which
were factory installed, then be sure to read
the information
q page 218, New tires or
wheels.
- Always make sure the damaged wheel or
even a flat tire and the jack and tool kit are
properly secured in the luggage compart­
ment and are not loose in the passenger
compartment.
- In an accident or sudden maneuver they
could fly forward, injuring anyone in the ve­
hicle.
- Always stor e damaged wheel, jack and tools
secure ly in the luggage compartment. Oth­
erwise, in an accident or sudden maneuver
they could fly forward, causing injury to pas­
sengers in the vehicle.
Spare tire
Space-saving spare tire
App lies to: vehicles wit h spare tire
Fig. 209 Luggage compartment: space -saving spare t ire
The spare tire is intended for short-term use on-
-
ly. Have the damaged tire checked and, if neces­
sary, replaced by an authorized Audi dealer or au­
thorized Audi Service Facility as soon as possible . .,..