2016 YAMAHA YZ450F wheel

CHASSIS
3-35
EASB111110CHECKING AND ADJUSTING THE STEER-
ING HEAD
1. Use a suitable stand to raise the front wheel
off the ground.
EWA
WARNING
Securely support the vehicle so that there is
no danger of it falling over.
2. Check:
• Steering head
Grasp the bottom of the front fork legs and
gently rock the front fork.
Blinding/looseness  Adjust the steering
head.
3. Remove:
• Handlebar
Refer to “HANDLEBAR” on page 4-32.
• Upper bracket
Refer to “STEERING HEAD” on page 4-51.
4. Adjust:
• Steering head
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Remove the washer “1”.
b. After loosening the ring nut “2” with a steer-
ing nut wrench “3”, tighten it to the specified
torque.
TIP
• Set the torque wrench at a right angle to the
steering nut wrench.
• Move the steering to the left and right a couple
of times to check that it moves smoothly.c. Turn the front fork to the right and left a few
times, and make sure that the steering ro-
tates smoothly. If it does not turn smoothly,
remove the lower bracket and check the up-
per and lower bearings.
Refer to “STEERING HEAD” on page 4-51.
d. Loosen the ring nut fully turn and then tight-
en it to specification with a steering nut
wrench.
EWA
WARNING
Do not overtighten the lower ring nut.
e. Check the steering head for looseness or
binding by turning the front fork all the way in
both directions. If any binding is felt, remove
the lower bracket and check the upper and
lower bearings.
Refer to “STEERING HEAD” on page 4-51.
f. Install the washer “1”.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
1
Steering nut wrench
90890-01403
Exhaust flange nut wrench
YU-A9472
Ring nut (initial tightening torque)
38 Nm (3.8 m·kgf, 27 ft·lbf)
Ring nut (final tightening torque)
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
3
2
T R..
T R..
1

4
CHASSIS
GENERAL CHASSIS........................................................................................ 4-1
REMOVING THE LEFT SIDE COVER ....................................................... 4-2
REMOVING THE SEAT ............................................................................. 4-2
REMOVING THE NUMBER PLATE ........................................................... 4-2
FRONT WHEEL................................................................................................ 4-3
REMOVING THE FRONT WHEEL............................................................. 4-4
CHECKING THE FRONT WHEEL ............................................................. 4-4
DISASSEMBLING THE FRONT WHEEL ................................................... 4-5
ASSEMBLING THE FRONT WHEEL ......................................................... 4-5
INSTALLING THE FRONT WHEEL ........................................................... 4-6
REAR WHEEL.................................................................................................. 4-7
REMOVING THE REAR WHEEL ............................................................... 4-8
CHECKING THE REAR WHEEL................................................................ 4-8
DISASSEMBLING THE REAR WHEEL ..................................................... 4-8
CHECKING AND REPLACING THE REAR WHEEL SPROCKET ............ 4-8
ASSEMBLING THE REAR WHEEL ........................................................... 4-9
INSTALLING THE REAR WHEEL............................................................ 4-10
FRONT BRAKE.............................................................................................. 4-12
INTRODUCTION ...................................................................................... 4-16
CHECKING THE FRONT BRAKE DISC .................................................. 4-16
REMOVING THE FRONT BRAKE CALIPER ........................................... 4-16
DISASSEMBLING THE FRONT BRAKE CALIPER................................. 4-16
CHECKING THE FRONT BRAKE CALIPER ........................................... 4-17
ASSEMBLING THE FRONT BRAKE CALIPER ....................................... 4-17
INSTALLING THE BRAKE CALIPER PISTON ........................................ 4-17
INSTALLING THE FRONT BRAKE CALIPER ......................................... 4-18
REMOVING THE FRONT BRAKE MASTER CYLINDER ........................ 4-19
CHECKING THE FRONT BRAKE MASTER CYLINDER......................... 4-19
ASSEMBLING THE FRONT BRAKE MASTER CYLINDER .................... 4-19
INSTALLING THE FRONT BRAKE MASTER CYLINDER....................... 4-20
REAR BRAKE................................................................................................ 4-22
INTRODUCTION ...................................................................................... 4-26
CHECKING THE REAR BRAKE DISC..................................................... 4-26
REMOVING THE REAR BRAKE CALIPER ............................................. 4-27
DISASSEMBLING THE REAR BRAKE CALIPER ................................... 4-27
CHECKING THE REAR BRAKE CALIPER .............................................. 4-27
ASSEMBLING THE REAR BRAKE CALIPER ......................................... 4-27
INSTALLING THE BRAKE CALIPER PISTON ........................................ 4-28
INSTALLING THE REAR BRAKE CALIPER ............................................ 4-28
REMOVING THE REAR BRAKE MASTER CYLINDER .......................... 4-29
CHECKING THE REAR BRAKE MASTER CYLINDER ........................... 4-29
ASSEMBLING THE REAR BRAKE MASTER CYLINDER....................... 4-30
INSTALLING THE REAR BRAKE MASTER CYLINDER ......................... 4-30

HANDLEBAR................................................................................................. 4-32
REMOVING THE HANDLEBAR............................................................... 4-34
CHECKING THE HANDLEBAR ............................................................... 4-34
INSTALLING THE HANDLEBAR ............................................................. 4-34
FRONT FORK................................................................................................. 4-38
REMOVING THE FRONT FORK LEGS ................................................... 4-40
DISASSEMBLING THE FRONT FORK LEGS ......................................... 4-40
CHECKING THE FRONT FORK LEGS ................................................... 4-41
ASSEMBLING THE FRONT FORK LEGS ............................................... 4-42
INSTALLING THE FRONT FORK LEGS ................................................. 4-48
STEERING HEAD........................................................................................... 4-51
REMOVING THE LOWER BRACKET...................................................... 4-52
CHECKING THE STEERING HEAD ........................................................ 4-52
INSTALLING THE STEERING HEAD ...................................................... 4-52
REAR SHOCK ABSORBER ASSEMBLY..................................................... 4-55
HANDLING THE REAR SHOCK ABSORBER ......................................... 4-58
DISPOSING OF A REAR SHOCK ABSORBER ...................................... 4-58
REMOVING THE REAR SHOCK ABSORBER ASSEMBLY.................... 4-58
REMOVING THE BEARING..................................................................... 4-59
CHECKING THE REAR SHOCK ABSORBER ASSEMBLY .................... 4-59
CHECKING THE CONNECTING ARM AND RELAY ARM ...................... 4-59
INSTALLING THE RELAY ARM............................................................... 4-59
INSTALLING THE REAR SHOCK ABSORBER ASSEMBLY .................. 4-60
SWINGARM.................................................................................................... 4-62
REMOVING THE SWINGARM................................................................. 4-63
REMOVING THE BEARING..................................................................... 4-63
CHECKING THE SWINGARM ................................................................. 4-63
INSTALLING THE SWINGARM ............................................................... 4-64
CHAIN DRIVE................................................................................................. 4-65
REMOVING THE DRIVE CHAIN.............................................................. 4-66
CHECKING THE DRIVE CHAIN .............................................................. 4-66
CHECKING THE DRIVE SPROCKET...................................................... 4-67
CHECKING THE REAR WHEEL SPROCKET ......................................... 4-67
INSTALLING THE DRIVE CHAIN ............................................................ 4-67

FRONT WHEEL
4-3
EASB111121
FRONT WHEEL
Removing the front wheel
Order Part name Q’ty Remarks
Use a suitable stand to raise the front wheel
off the ground.
1 Front wheel axle pinch bolt 4 Loosen.
2 Front wheel axle nut 1
3 Front wheel axle 1
4 Front wheel 1
5Collars 2
6Oil seals 2
7 Bearing 2
8 Brake disc 1
For installation, reverse the removal proce-
dure.
12 Nm (1.2 mkgf, 8.7 ftIbf)T.R
.
New
New
LT
LS
LS
LS
5
76
5 6 7
(6)
8
12
1 3
21 Nm (2.1 mkgf, 15 ftIbf)T.R.
21 Nm (2.1 mkgf, 15 ftIbf)T.R.
4
115 Nm (11.5 mkgf, 83 ftlbf)T.R.

FRONT WHEEL
4-4
EASB111122REMOVING THE FRONT WHEEL
1. Use a suitable stand to raise the front wheel
off the ground.
EWA
WARNING
Securely support the vehicle so that there is
no danger of it falling over.
2. Remove:
• Front wheel
EASB111123CHECKING THE FRONT WHEEL
1. Check:
• Front wheel axle
Roll the front wheel axle on a flat surface.
Bends  Replace.
EWA
WARNING
Do not attempt to straighten a bent wheel
axle.
2. Check:
•Tire(s)
• Front wheel
Damage/wear  Replace.
Refer to “CHECKING THE TIRES” on page
3-34 and “CHECKING THE WHEELS” on
page 3-34.
3. Check:
• Spokes
Bend/damage  Replace.
Loose  Tighten.
Tap the spokes with a screwdriver.
TIP
A tight spoke will emit a clear, ringing tone; a
loose spoke will sound flat.
4. Tighten:
• Spokes
Refer to “CHECKING AND TIGHTENING
THE SPOKES” on page 3-34.
TIP
After tightening the spokes, measure the wheel
runout.
5. Measure:
• Wheel radial runout “a”
• Wheel lateral runout “b”
Out of specification  Repair/replace.
6. Check:
•Collars
Damage/wear  Replace.
7. Check:
• Bearing
Front wheel turns roughly or is loose  Re-
place the wheel bearings.
• Oil seals
Damage/wear  Replace.
Spokes
2.5 Nm (0.25 m·kgf, 1.8 ft·lbf)
Radial wheel runout limit
2.0 mm (0.08 in)
Lateral wheel runout limit
2.0 mm (0.08 in)
T R..
ab

FRONT WHEEL
4-5
EASB111124DISASSEMBLING THE FRONT WHEEL
1. Remove:
• Oil seals
• Bearings
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Clean the outside of the front wheel hub.
b. Remove the oil seals “1” with a flat-head
screwdriver.
TIP
To prevent damaging the wheel, place a rag “2”
between the screwdriver and the wheel sur-
face.
c. Remove the bearings with a bearing puller.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
EASB111125ASSEMBLING THE FRONT WHEEL
1. Install:
• Bearing (left side) “1”
• Spacer “2”
• Bearing (right side) “3”
• Oil seals “4”
TIP
• Apply the lithium-soap-based grease to the
bearing and the oil seal lip when installing.
• Left side of bearing shall be installed first.
• Install the oil seal with its manufacture’s
marks or numbers facing outward.
ECA
NOTICE
Install the bearing by pressing its outer race
parallel.
TIP
Use a socket “1” that matches the diameter of
the bearing outer race and that of the oil seal.
2. Install:
• Brake disc “1”
• Brake disc bolt “2”
TIP
Tighten the bolts in stages and in a crisscross
pattern.
12
New
Brake disc bolt
12 Nm (1.2 m·kgf, 8.7 ft·lbf)
LOCTITE®
4
3
2
1
4
New
New
1
T R..

FRONT WHEEL
4-6
3. Install:
• Collar “1”
TIP
Apply the lithium-soap-based grease on the oil
seal lip.
EASB111126INSTALLING THE FRONT WHEEL
1. Install:
• Front wheel
TIP
Install the brake disc “1” between the brake
pads “2” correctly.
2. Install:
• Front wheel axle “1”
TIP
Apply the lithium-soap-based grease to the
front wheel axle.3. Tighten:
• Front wheel axle nut “1”
ECA
NOTICE
Before tightening the front wheel axle nut,
push down hard on the handlebar(s) several
times and check if the front fork rebounds
smoothly.
4. Tighten:
• Front wheel axle pinch bolt “1”
1
LS
Front wheel axle nut
115 Nm (11.5 m·kgf, 83 ft·lbf)
Front wheel axle pinch bolt
21 Nm (2.1 m·kgf, 15 ft·lbf)
T R..
1
T R..
1 1

REAR WHEEL
4-7
EASB111127
REAR WHEEL
Removing the rear wheel
Order Part name Q’ty Remarks
Use a suitable stand to raise the rear wheel
off the ground.
1 Nut (rear wheel axle) 1
2 Rear wheel axle 1
3 Drive chain puller 2
4 Rear wheel 1
5Collars 2
6 Rear wheel sprocket 1
7Oil seals 2
8 Circlip 1
9 Bearing 3
10 Brake disc 1
For installation, reverse the removal proce-
dure.
(6)
21 Nm (2.1 m•kgf, 15 ft•Ibf)T.R.
2 5
7 9
LS
LS(6)
46
1
(6) 3
LS
8
9 10
7 5
LT
14 Nm (1.4 m•kgf, 10 ft•Ibf)T.R.
3
21 Nm (2.1 m•kgf, 15 ft•Ibf)T.R.
42 Nm (4.2 m•kgf, 30 ft•Ibf)T.R.
135 Nm (13.5 m•kgf, 98 ft•lbf)T.R.