2016 YAMAHA WR 450F Owners Manual

ENGINE
3-23
INTAKE
Example:
Valve clearance (cold) 0.13–0.20 mm
(0.0051–0.0079 in)
Installed is 175
Measured clearance 0.27 mm (0.0106 in)
Replace 175 pad with 185 pad
Pad No.175 = 1.75 mm (0.0689 in)
Pad No.185 = 1.85 mm (0.0728 in)
120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.03 0.07120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230
0.00 0.02
120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225
0.08 0.12 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235
0.13 0.20 0.21 0.25 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.26 0.30 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.31 0.35 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.36 0.40 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.41 0.45 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.46 0.50 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.51 0.55 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.56 0.60 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.61 0.65 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.66 0.70 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.71 0.75 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.76 0.80 180 185 190 195 200 205 210 215 220 225 230 235 240
0.81 0.85 185 190 195 200 205 210 215 220 225 230 235 240
0.86 0.90 190 195 200 205 210 215 220 225 230 235 240
0.91 0.95 195 200 205 210 215 220 225 230 235 240
0.96 1.00 200 205 210 215 220 225 230 235 240
1.01 1.05 205 210 215 220 225 230 235 240
1.06 1.10 210 215 220 225 230 235 240
1.11 1.15 215 220 225 230 235 240
1.16 1.20 220 225 230 235 240
1.21 1.25 225 230 235 240
1.26 1.30 230 235 240
1.31 1.35 235 240
1.36 1.40 240
A. Measured clearance
B. Installed pad number
C. Standard clearance

ENGINE
3-24
EXHAUST
Example:
Valve clearance (cold) 0.18–0.25 mm
(0.0071–0.0098 in)
Installed is 175
Measured clearance 0.32 mm (0.0126 in)
Replace 175 pad with 185 pad
Pad No.175 = 1.75 mm (0.0689 in)
Pad No.185 = 1.85 mm (0.0728 in)
EAS2GC1100CLEANING THE SPARK ARRESTER
Refer to “CLEANING THE SPARK ARREST-
ER” on page 6-7.
120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.00 0.02120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220
0.03 0.07 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225
0.08 0.12 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230
0.13 0.17 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235
0.18 0.25
0.26 0.30 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.31 0.35 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.36 0.40 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.41 0.45 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.46 0.50 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.51 0.55 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.56 0.60 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.61 0.65 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.66 0.70 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.71 0.75 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.76 0.80 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.81 0.85 180 185 190 195 200 205 210 215 220 225 230 235 240
0.86 0.90 185 190 195 200 205 210 215 220 225 230 235 240
0.91 0.95 190 195 200 205 210 215 220 225 230 235 240
0.96 1.00 195 200 205 210 215 220 225 230 235 240
1.01 1.05 200 205 210 215 220 225 230 235 240
1.06 1.10 205 210 215 220 225 230 235 240
1.11 1.15 210 215 220 225 230 235 240
1.16 1.20 215 220 225 230 235 240
1.21 1.25 220 225 230 235 240
1.26 1.30 225 230 235 240
1.31 1.35 230 235 240
1.36 1.40 235 240
1.41 1.45 240
A. Measured clearance
B. Installed pad number
C. Standard clearance

CHASSIS
3-25
EAS2GC1101
CHASSIS
EAS2GC1102BLEEDING THE BRAKE SYSTEMEWA
WARNING
Bleed the brake system whenever:
• The system is disassembled.
• A brake hose is loosened, disconnected, or replaced.
• The brake fluid level is very low.
• Brake operation is faulty.
1. Remove: • Brake master cylinder cap
• Reservoir diaphragm
• Reservoir float (front brake)
• Protector (rear brake)
TIP
• Be careful not to spill any brake fluid or allow the reservoir to overflow.
• Make sure that there is enough brake fluid be-
fore applying the brake. Ignoring this precau-
tion could allow air to enter the brake system,
considerably lengthening the bleeding proce-
dure.
• If bleeding is difficult, it may be necessary to let the brake fluid settle for a few hours. Re-
peat the bleeding procedure when the tiny
bubbles in the hose have disappeared.
2. Bleed the brake system.
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Fill the reservoir to the proper level with the recommended brake fluid.
b. Install the reservoir diaphragm.
c. Connect the plastic hose “1” to the bleed screw “2” securely, and place a container
under the end of the plastic hose. d. Slowly apply the brake several times.
e. Fully pull the brake lever or fully press down
the brake pedal and hold it in position.
f. Loosen the bleed screw.
TIP
Loosening the bleed screw will release the
pressure in the brake caliper and cause the
brake lever to contact the throttle grip or the
brake pedal to fully extend.
g. Tighten the bleed screw and then release the brake lever or brake pedal.
h. Repeat steps (d) to (g) until all of the air bub- bles have disappeared from the brake fluid
in the plastic hose.
TIP
During the procedure, keep adding brake fluid
to the reservoir.
ECA
NOTICE
• Wipe off any brake fluid on the brake discs, tires, wheels, etc.
• Brake fluid may erode painted surfaces or
plastic parts. Always clean up spilled fluid
immediately.
i. Tighten the bleed screw.
j. Pour brake fluid to the reservoir up to the specified level.
Refer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-30.
EWA
WARNING
After bleeding the hydraulic brake system,
check the brake operation.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
1
2
A
A. Front
B. Rear
Bleed screw
6 Nm (0.6 m·kgf, 4.3 ft·lbf)
2
1B
T R..

CHASSIS
3-26
EAS2GC1103CHECKING THE BRAKE HOSE
1. Check:• Brake hose “1”Cracks/damage/wear  Replace.
2. Check: • Brake hose clamp
Loose connection  Tighten the clamp bolt.
3. Stand the vehicle upright and apply the front brake and the rear brake several times.
4. Check: • Brake hosesBrake fluid leaks  Replace the damaged
brake hose.
Refer to “FRONT BRAKE” on page 5-13.
Refer to “REAR BRAKE” on page 5-23.
EAS2GC1104ADJUSTING THE FRONT BRAKE
1. Check: • Brake lever position “a” 2. Remove:
• Brake lever cover
3. Adjust: • Brake lever position
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Loosen the locknut “1”.
b. Turn the adjusting bolt “2” in direction “a” or “b” until the specified brake lever position is
obtained.
c. Tighten the locknut.
EWA13050
WARNING
A soft or spongy feeling in the brake lever
can indicate the presence of air in the brake
system. Before the vehicle is operated, the
air must be removed by bleeding the brake
system. Air in the brake system will consid-
erably reduce braking performance.
ECA13490
NOTICE
After adjusting the brake lever position,
make sure there is no brake drag.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
4. Install: • Brake lever cover
A. Front
B. Rear
Brake lever position95 mm (3.74 in)
Extent of adjustment 86–105 mm (3.39–4.13 in)
1
1
Direction “a”Brake lever position is increased.
Direction “b” Brake lever position is decreased.
Locknut5 Nm (0.5 m·kgf, 3.6 ft·lbf)
a
b
T R..

CHASSIS
3-27
EAS2GC1105ADJUSTING THE REAR BRAKE
1. Check:• Brake pedal position “a”(distance from the top of the rider footrest to
the top of the brake pedal)
Out of specification  Regulate.
2. Adjust: • Brake pedal position
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Loosen the locknut “1”.
b. Turn the adjusting bolt “2” in direction “a” or “b” until the specified brake pedal position is
obtained.
c. Tighten the locknut.
EWA
WARNING
A soft or spongy feeling in the brake pedal
can indicate the presence of air in the brake
system. Before running, bleed the brake
system. Air in the brake system will cause
braking performance to be reduced.
ECA
NOTICE
After adjusting the brake pedal position,
make sure that there is no brake drag.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
EAS2GC1106CHECKING THE FRONT BRAKE PADS
1. Measure: • Brake pad thickness “a”Out of specification  Replace as a set.
TIP
The pads worn up to the indicator “b” grooves
mean that the brake pad thickness limit is
reached.
2. Replace:
• Brake pads
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Remove the pad pin plug “1”.
b. Loosen the pad pin “2”.
Brake pedal position
5.0 mm (0.20 in)
Direction “a” Brake pedal is raised.
Direction “b”
Brake pedal is lowered.
Locknut6 Nm (0.6 m·kgf, 4.3 ft·lbf)
1
2
a
b
T R..
Brake pad lining thickness
4.4 mm (0.17 in)
Limit 1.0 mm (0.04 in)
a
b
a
1

CHASSIS
3-28
c. Remove the brake caliper “3” from the front fork.
d. Remove the pad pin and brake pads “4”.
e. Connect the plastic hose “5” to the bleed screw “6” and place a container under the
end of the plastic hose.
f. Loosen the bleed screw and push the brake caliper piston in.
EWA
WARNING
Do not reuse the drained brake fluid.
g. Tighten the bleed screw.
h. Install the brake pads “7” and the pad pin.
TIP
• Install the brake pads with their projections “a” into the brake caliper recesses “b”.
• Temporarily tighten the pad pin at this point. i. Install the brake caliper “8” and tighten the
pad pin “9”.
j. Install the pad pin plug “10”.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
3. Check: • Brake fluid levelRefer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-30.
4. Check: • Brake lever operation
A softy or spongy feeling  Bleed the brake
system.
Refer to “BLEEDING THE BRAKE SYS-
TEM” on page 3-25.
Bleed screw
6 Nm (0.6 m·kgf, 4.3 ft·lbf)
3
2
4
6
5
T R..
Bolt (brake caliper)23 Nm (2.3 m·kgf, 17 ft·lbf)
Pad pin 17 Nm (1.7 m·kgf, 12 ft·lbf)
Pad pin plug 2.5 Nm (0.25 m·kgf, 1.8 ft·lbf)
7
a
b
T R..
8
9
T R..
10

CHASSIS
3-29
EAS2GC1107CHECKING THE REAR BRAKE PADS
1. Measure:• Brake pad thickness “a”Out of specification  Replace as a set.
TIP
The pads worn up to the indicator “b” grooves
mean that the brake pad thickness limit is
reached.
2. Replace:
• Brake pads
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Remove the protector “1” and the pad pin
plug “2”.
b. Loosen the pad pin “3”.
c. Remove the rear wheel “4” and the brake caliper “5”.
Refer to “REAR WHEEL” on page 5-9. d. Remove the pad pin “6” and the brake pads
“7”.
e. Connect the plastic hose “8” to the bleed screw “9” and place a container under the
end of the plastic hose.
f. Loosen the bleed screw and push the brake caliper piston in.EWA
WARNING
Do not reuse the drained brake fluid.
g. Tighten the bleed screw.
h. Install the brake pad “10” and the pad pin “11”.
TIP
• Install the brake pads with their projections “a” into the brake caliper recesses “b”.
• Temporarily tighten the pad pin at this point.
Brake pad lining thickness
6.4 mm (0.25 in)
Limit 1.0 mm (0.04 in)
b a
a
1
2
3
4
5
Bleed screw 6 Nm (0.6 m·kgf, 4.3 ft·lbf)
7
6
9
8
T R..
10
11
a
b

CHASSIS
3-30
i. Install the brake caliper “12” and the rear wheel “13”.
Refer to “REAR WHEEL” on page 5-9.
j. Tighten the pad pin “14”.
k. Install the pad pin plug “15” and the protector “16”.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
3. Check:• Brake fluid levelRefer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-30.
4. Check: • Brake pedal operationA softy or spongy feeling  Bleed the brake
system.
Refer to “BLEEDING THE BRAKE SYS-
TEM” on page 3-25.
EAS2GC1108CHECKING THE REAR BRAKE PAD INSU-
LATOR
1. Remove: • Brake padsRefer to “REAR BRAKE” on page 5-23. 2. Check:
• Rear brake pad insulator “1”Damage  Replace.
EAS2GC1109CHECKING THE BRAKE FLUID LEVEL
1. Stand the vehicle upright on a level surface.
TIP
In order to ensure a correct reading of the brake
fluid level, make sure that the top of the brake
fluid reservoir is horizontal.
2. Check:
• Brake fluid levelThe minimum level mark “a” or below 
Add.
EWA
WARNING
• Use only the designated brake fluid. Other brake fluids may cause the rubber seals to
deteriorate, causing leakage and poor
brake performance.
• Refill with the same type of brake fluid that
is already in the system. Mixing brake flu-
ids may result in a harmful chemical reac-
tion, leading to poor brake performance.
Pad pin
17 Nm (1.7 m·kgf, 12 ft·lbf)
Pad pin plug 2.5 Nm (0.25 m·kgf, 1.8 ft·lbf)
Bolt (protector) 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
T R..
13
14
12
T R..
15 16
Specified brake fluidDOT 4
A. Front brake
B. Rear brake