2016 YAMAHA WR 450F fuse diagram

CABLE ROUTING DIAGRAM
2-34
1. Clutch cable
2. Throttle cable (return)
3. Throttle cable (pull)
4. Engine stop switch lead
5. Coupler for connecting optional part
6. Engine stop switch coupler
7. Rectifier/regulator coupler
8. AC magneto lead
9. Starter knob/idle screw
10. Engine ground sub-lead
11. Starter motor lead
12. Radiator fan fuse
13. Taillight lead
14. Headlight relay (yellow tape)
15. Starting circuit cut-off relay (no identification tape)
16. Diode
17. Holder plate
18. Left of the vehicle:radiator fan motor relay (blue tape)
Right of the vehicle:main relay (red tape)
19. Neutral switch lead
20. Front engine bracket
21. Plastic locking tie
22. Radiator hose
23. Neutral switch coupler
24. Crankshaft position sensor coupler
25. Tension arm
26. Wire harness
27. Tank rail
28. Rectifier/regulator
29. Rectifier/regulator bracket
30. Rear frame
31. Side cover 5
32. Crankcase cover
33. Crankcase
34. Lead holder
35. Frame
36. Engine ground sub-lead coupler
A. Pass the engine stop switch lead between the frame and the cable holder.
B. Insert the coupler for connecting optional part into the connector, and fix it to the bracket.
C. Insert and fix the engine stop switch coupler to the bracket.
D. Insert and fix the rectifie r/regulator coupler to the
bracket.
E. Pass the AC magneto lead to the front of the ve- hicle beyond the starter knob/idle screw and to
the rear of the vehicle beyond the radiator. No
pinch is allowed between the radiator and the
tension arm.
F. Make sure that there is no slack so that the starter motor lead cannot touch the end of the bolt.
G. Place the rear grommet of the starter motor lead matching the rear end of the side cover.
H. Insert the radiator fan motor fuse into the protru- sion of the holder plate.
I. Place the diode on top of the rear fender on the inner side of the rear frame.
J. Bring the neutral switch lead into line with the crankcase cover with no sag allowed.
K. Route the AC magneto lead inside the starter clutch cover.
L. Pass the neutral switch l ead to the inside of the
front engine bracket (the side of the vehicle).
M. Insert the plastic locking tie into the bracket hole and clamp the clutch cable. Clamp it so that the
lock of the plastic locking tie faces downward,
and then cut off the end of the plastic locking tie. N. Pass the clutch cable
with no downward sag al-
lowed.
O. Place the grommet of the clutch cable so that it contacts the radiator hose. Route the clutch cable
outside the neutral switch lead, AC magneto lead
and starter motor lead.
P. Route each lead so that the leads are not pinched
between the radiator hose and the frame.
Q. 40 mm (1.57 in)
R. Clamp the clutch cable, AC magneto lead, neu- tral switch lead and starter motor lead by the plas-
tic locking tie. Make sure that they are clamped at
the positioning tapes in the clutch cable and the
starter motor lead. Make the lock on the plastic
locking tie face the front of the vehicle, and cut
the end.
S. Clamp the starter motor lead to the inside of the tension arm with a plastic locking tie. Clamp it so
that the lock of the plastic locking tie faces up-
ward and outward, and do not cut off the end of
the plastic locking tie. R oute the lead so that there
is no slack at the bottom from the clamp position
onwards.
T. After connecting the neutral switch coupler, at- tach the coupler cover.
U. After connecting the crankshaft position sensor coupler, attach the coupler cover.
V. Pass the rectifier/regulator lead to the inside of the tension arm (the side of the vehicle).
W. Pass the main harness to the front of the radiator
hose (the front of the vehicle), and to the inside of
the clutch cable (the side of the vehicle).
X. Pass the engine stop switch lead between the coupler for connecting optional part and the tank
rail, with the lead on the main harness side facing
the top of the vehicle.
Y. Insert the starter motor lead completely into the end of the side cover 5.
Z. Clamp the clutch cable at the front of the lead (the
front of the vehicle).
AA.Insert the clip of the pl astic locking tie into the
frame. Face the lock of the plastic locking tie for-
ward, and then cut off the end.

CHARGING SYSTEM
9-14
EAS2GC1365TROUBLESHOOTING
The battery is not being charged.
TIP
Before troubleshooting, remove the following part (s):
1. Seat
2. Side cover (left/right)1. Check the fuse. Refer to “CHECKING THE FUSES”
on page 9-68. NG

Replace the fuse(s).
OK 
2. Check the battery. Refer to “CHECKING AND
CHARGING THE BATTERY” on
page 9-69. NG

• Clean the battery terminals.
• Recharge or replace the battery.
OK 
3. Check the stator coil. Refer to “CHECKING THE STA-
TOR COIL” on page 9-76. NG

Replace the stator assembly.
OK 
4. Check the rectifier/regulator. Refer to “CHECKING THE RECTI-
FIER/REGULATOR” on page 9-76. NG

Replace the rectifier/regulator.
OK 
5. Check the entire charging system’s wiring.
Refer to “CIRCUIT DIAGRAM” on
page 9-12. NG

Properly connect or repair the charging
system’s wiring.
OK 
This circuit is OK.

LIGHTING SYSTEM
9-18
EAS2GC1367TROUBLESHOOTING
Any of the following fail to light: headlight or meter light.
TIP
Before troubleshooting, remove the following part (s):
1. Seat
2. Side cover (left)
3. Air scoop (left/right)
4. Fuel tank1. Check the each bulbs condition. Refer to “CHECKING THE BULBS
AND BULB SOCKETS” on page 9-
67. NG

Replace the bulb (s).
OK 
2. Check the fuse. Refer to “CHECKING THE FUSES”
on page 9-68. NG

Replace the fuse(s).
OK 
3. Check the battery. Refer to “CHECKING AND
CHARGING THE BATTERY” on
page 9-69. NG

• Clean the battery terminals.
• Recharge or replace the battery.
OK 
4. Check the main relay. Refer to “CHECKING THE RE-
LAYS” on page 9-72. NG

Replace the main relay.
OK 
5. Check the headlight relay. Refer to “CHECKING THE RE-
LAYS” on page 9-72. NG

Replace the headlight relay.
OK 
6. Check the entire lighting system’s wiring.
Refer to “CIRCUIT DIAGRAM” on
page 9-16. NG

Properly connect or repair the lighting sys-
tem’s wiring.
OK 
Replace the ECU, meter assembly, or
taillight.

SIGNALING SYSTEM
9-22
EAS2GC1369TROUBLESHOOTING
• The speedometer does not operate normally.
• The fuel indicator light does not come on.
TIP
Before troubleshooting, remove the following part (s):
1. Seat
2. Side cover (left/right)
3. Air scoop (left/right)
4. Fuel tank
Check the signaling system
The speedometer fails to operate.
1. Check the fuse.Refer to “CHECKING THE FUSES”
on page 9-68. NG

Replace the fuse(s).
OK 
2. Check the battery. Refer to “CHECKING AND
CHARGING THE BATTERY” on
page 9-69. NG

• Clean the battery terminals.
• Recharge or replace the battery.
OK 
3. Check the main relay. Refer to “CHECKING THE RE-
LAYS” on page 9-72. NG

Replace the main relay.
OK 
4. Check the entire signaling system’s wiring.
Refer to “CIRCUIT DIAGRAM” on
page 9-20. NG

Properly connect or repair the signaling
system’s wiring.
OK 
This circuit is OK.
1. Check the speed sensor. Refer to “CHECKING THE SPEED
SENSOR” on page 9-77. NG

Replace the speed sensor.
OK 
2. Check the entire signaling system’s wiring.
Refer to “CIRCUIT DIAGRAM” on
page 9-20. NG

Properly connect or repair the signaling
system’s wiring.
OK 
Replace the meter assembly.

COOLING SYSTEM
9-26
EAS2GC1372TROUBLESHOOTING
The radiator fan motor fails to turn.
TIP
Before troubleshooting, remove the following part(s):
1. Seat
2. Side cover (left)
3. Air scoop (left/right)
4. Fuel tank1. Check the fuse. Refer to “CHECKING THE FUSES”
on page 9-68. NG

Replace the fuse(s).
OK 
2. Check the battery. Refer to “CHECKING AND
CHARGING THE BATTERY” on
page 9-69. NG

• Clean the battery terminals.
• Recharge or replace the battery.
OK 
3. Check the main relay. Refer to “CHECKING THE RE-
LAYS” on page 9-72. NG

Replace the main relay.
OK 
4. Check the radiator fan motor. Refer to “CHECKING THE RADIA-
TOR FAN MOTOR” on page 9-78. NG

Replace the radiator fan motor.
OK 
5. Check the radiator fan motor relay. Refer to “CHECKING THE RE-
LAYS” on page 9-72. NG

Replace the radiator fan motor relay.
OK 
6. Check the coolant temperature sen- sor.
Refer to “CHECKING THE COOL-
ANT TEMPERATURE SENSOR”
on page 9-78. NG

Replace the coolant temperature sensor.
OK 
7. Check the entire cooling system’s wiring.
Refer to “CIRCUIT DIAGRAM” on
page 9-16. NG

Properly connect or repair the cooling sys-
tem’s wiring.
OK 
Replace the ECU.

FUEL PUMP SYSTEM
9-58
EAS2GC1381TROUBLESHOOTING
The fuel pump fails to operate.
TIP
Before troubleshooting, remove the following part(s):
1. Seat
2. Side cover (left/right)
3. Air scoop (left/right)
4. Fuel tank1. Check the fuse. Refer to “CHECKING THE FUSES”
on page 9-68. NG

Replace the fuse(s).
OK 
2. Check the battery. Refer to “CHECKING AND
CHARGING THE BATTERY” on
page 9-69. NG

• Clean the battery terminals.
• Recharge or replace the battery.
OK 
3. Check the engine stop switch. Refer to “CHECKING THE
SWITCHES” on page 9-64. NG

Replace the engine stop switch.
OK 
4. Check fuel pressure. Refer to “CHECKING THE FUEL
PRESSURE” on page 8-5. NG

Replace the fuel pump.
OK 
5. Check the fuel pump system wire harness connections.
Refer to “CIRCUIT DIAGRAM” on
page 9-56. NG

Properly connect or repair the fuel pump
system’s wiring.
OK 
Replace the ECU.

EAS2GC1427
WIRING DIAGRAM
WR450F/WR450FG 2016
1. Joint connector
2. Joint connector
3. Joint connector
4. AC magneto
5. Rectifier/regulator
6. Headlight relay
7. Main relay
8. Engine ground
9. Battery
10. Frame ground
11. Starter relay
12. Main fuse
13. Starter motor
14. Starter relay diode
15. Indicator light
16. Engine trouble warning light
17. Fuel level warning light
18. Resistor
19. Fuel sender
20. Diode
21. Coupler for connecting option-al part
22. ECU (engine control unit)
23. Ignition coil
24. Spark plug
25. Injector
26. Fuel pump
27. Radiator fan motor relay
28. Radiator fan motor fuse
29. Radiator fan motor
30. Joint connector
31. Intake air temperature sensor
32. Coolant temperature sensor
33. Throttle position sensor
34. Intake air pressure sensor
35. Lean angle sensor
36. Engine stop switch
37. Neutral switch
38. Diode
39. Starting circuit cut-off relay
40. Clutch switch
41. Start switch
42. Joint connector
43. Taillight
44. Headlight
45. Coupler for connecting option- al switch
46. Speed sensor
47. Multi-function display
48. Frame ground
49. Ignition coil sub-lead
50. Negative battery lead
51. Engine ground sub-lead
EAS2GC1428
COLOR CODE
BBlack
Br Brown
Ch Chocolate
Dg Dark green
G Green
Gy Gray
LBlue
Lg Light green
O Orange
PPink
RRed
Sb Sky blue
WWhite
Y Yellow
B/L Black/Blue
B/O Black/Orange
B/W Black/White
B/Y Black/Yellow
Br/W Brown/White
G/B Green/Black
G/W Green/White
G/Y Green/Yellow
L/B Blue/Black
L/G Blue/Green
L/R Blue/Red
L/W Blue/White
L/Y Blue/Yellow
P/L Pink/Blue
R/B Red/Black
R/L Red/Blue
R/W Red/White
R/Y Red/Yellow
W/B White/Black
Y/B Yellow/Black
Y/G Yellow/Green
Y/R Yellow/Red