2016 TOYOTA MIRAI display

171
2. SETUP
PHONE
7
1Display the phone top screen.
(P.146)
2Select .
3Select “Settings” .
1Display the “Phone/Message Settings”
screen. (P.160)
2Select “Phone Display Settings” .
3Select the desired item to be set.
INFORMATION
●Depending on the phone, these func-
tions may not be available.
DISPLAYING THE “Messaging
Settings” SCREEN IN A
DIFFERENT WAY
“Phone Display Settings”
SCREEN
No.Function
Select to change the incoming call
display.
“Full Screen” : When a call is re-
ceived, the hands-free screen is dis-
played and can be operated on the
screen.
“Drop-down” : A message is dis-
played on the upper side of the
screen.
Select to set display of the contact/
history transfer completion message
on/off.
Select to reset all setup items.
INFORMATION
● Depending on the phone, these func-
tions may not be available.

176
3. WHAT TO DO IF...
When using the Bluetooth® message function
 In
other situations
SymptomLikely causeSolution
Page
Cellular
phoneThis
system
Messages cannot be
viewed.
Message transfer is
not enabled on the
cellular phone.
Enable message
transfer on the cellu-
lar phone (approve
message transfer on
the phone).

Automatic transfer
function on this sys-
tem is set to off.Set automatic trans-
fer function on this
system to on.
170
New message notifi-
cations are not dis-
played.
Notification of SMS/
MMS/E-mail recep-
tion on this system is
set to off.Set notification of
SMS/MMS/E-mail
reception on this sys-
tem to on.
170
Automatic message
transfer function is
not enabled on the
cellular phone.Enable automatic
transfer function on
the cellular phone.

SymptomLikely causeSolution
Page
Cellular phoneThis
system
The Bluetooth® con-
nection status is dis-
played at the top of
the screen each time
the power switch is
turned to ACCESSO-
RY or ON mode.
Connection confir-
mation display on
this system is set to
on.To turn off the dis-
play, set connection
confirmation display
on this system to off.
51

178
1. QUICK REFERENCE ................... 180
MAP SCREEN ..................................... 180
NAVIGATION OPTIONS SCREEN...... 182
2. MAP SCREEN OPERATION ....... 183
CURRENT POSITION DISPLAY ......... 183
MAP SCALE ........................................ 183
ORIENTATION OF THE MAP ............. 184
SWITCHING THE MAP MODE............ 184
SCREEN SCROLL OPERATION ........ 186
ADJUSTING LOCATION IN SMALL 
INCREMENTS................................... 187
3. MAP SCREEN INFORMATION ... 188
DISPLAYING MAP INFORMATION .... 188
DISPLAYING INFORMATION 
ABOUT THE ICON WHERE 
THE CURSOR IS SET ...................... 190
STANDARD MAP ICONS .................... 191
4. TRAFFIC INFORMATION ............ 192
DISPLAYING TRAFFIC 
INFORMATION ON THE MAP .......... 194
1. DESTINATION SEARCH 
SCREEN .................................... 195
2. SEARCH OPERATION.. .............. 19
7
SELECTING SEARCH AREA .............. 198
SETTING HOME AS DESTINATION ... 198
SETTING PRESET DESTINATIONS 
AS DESTINATION ............................. 198
SEARCHING BY ADDRESS ................ 199
SEARCHING BY POINT OF 
INTEREST ......................................... 200
SEARCHING FROM PREVIOUS DESTINATIONS ................................ 204
SEARCHING BY ADDRESS BOOK .... 204
SEARCHING BY EMERGENCY .......... 205
SEARCHING BY INTERSECTION 
AND FREEWAY ................................ 205
SEARCHING BY MAP ......................... 207
SEARCHING BY COORDINATES ....... 207
3. STARTING ROUTE 
GUIDANCE ....... ......................... 20
8
STARTING ROUTE GUIDANCE.......... 208
PAUSING GUIDANCE ......................... 211
1BASIC OPERATION2DESTINATION SEARCH
8
NAVIGATION SYSTEM

180
1. BASIC OPERATION
1. QUICK REFERENCE
MAP SCREEN
To display this screen, press the “APPS” button, then select “Navigation” on the
“Apps” screen.
No.NameFunctionPage
2D North-up, 2D
heading-up or 3D
heading-up sym-
bolIndicates whether the map orientation is set to
north-up or heading-up. The letter(s) beside this
symbol indicate the vehicle’s heading direction
(e.g. N for north). In 3D map, only a heading-up
view is available.
184
Options buttonSelect to display the “Navigation Options” screen.182
“GPS” mark 
(Global Position-
ing System)Shows that the vehicle is receiving signals from
the GPS.241
Traffic indicator
Shows that traffic information is received. Select
to start voice guidance for traffic information.
When traffic information is received via HD, HD
mark is displayed on the right.
192
Scale indicatorThis figure indicates the map scale.183

181
1. BASIC OPERATION
NAVIGATION SYSTEM
8
Zoom in/out but-
tonSelect to magnify or reduce the map scale. When
either button is selected, the map scale indicator
bar appears at the bottom of the screen.
183
Current position
button/voice
guidance buttonSelect to display the current position address.Select to repeat voice guidance.183
Destination but-
tonSelect to display the “Destination” screen.195
Speed limit icon
Indicates the speed limit on the current road.
The display of the speed limit icon can be set to
on/off.
188
Route informa-
tion bar
Displays the current street name, or the distance
with the estimated travel time/arrival time to the
destination. The route information bar fills from
left to right as the vehicle progresses on the
route.
212
Route informa-
tion buttonSelect to change the display between the current
street name and the distance with the estimated
travel/arrival time.
213
No.NameFunctionPage

182
1. BASIC OPERATION
NAVIGATION OPTIONS SCREEN
The navigation options allow you to change map configurations, display/hide POI
icons, and edit the navigation routes. To display the “Navigation Options” screen,
press the “APPS” button, select “Navigation” on the “Apps” screen, and select
“Options” on the map screen.
No.FunctionPage
Select to display the desired map configuration.184
Select to set display of the map information such as POI icons, route
trace, speed limit, etc.188
Select to display the map version and coverage area.243
Select to edit the set route.218
Select to pause or resume route guidance.211
Select to display the overview of the entire route.213

183
1. BASIC OPERATION
NAVIGATION SYSTEM
8
2. MAP SCREEN OPERATION
1Press the “APPS” button.
2Select “Navigation” .
3Check that the current position map is
displayed.
1Select or to change the
scale of the map screen.
 The scale indicator bar appears at the bot -
tom of the screen.
 Sel
ect and hold or to con-
tinue changing the scale of the map
screen.
 The sc
ale of the map screen can also be
changed by selecting the scale bar
directly. This function is not available while
driving.
CURRENT POSITION
DISPLAY
To correct the current position manu-
ally:
P. 2 3 3
INFORMATION
● While driving, the current position mark
is fixed on the screen and the map
moves.
● The current position is automatically set
as the vehicle receives signals from the
GPS (Global Positioning System). If the
current position is not correct, it is auto-
matically corrected after the vehicle
receives signals from the GPS.
● After the battery disconnection, or on a
new vehicle, the current position may
not be correct. As soon as the system
receives signals from the GPS, the cor-
rect current position is displayed.
MAP SCALE
INFORMATION
●The map scale is displayed above the
zoom in button at the bottom left of the
screen.

184
1. BASIC OPERATION
1Select , or .
 No
rth-up screen
H
eading-up screen
3D
screen : North-up symbol
R

egardless of the direction of vehicle trav-
el, north is always up.
: Heading-up symbol
The direction of vehicle travel is always up.
: 3D Heading-up symbol
The direction of vehicle travel is always up.
 The letter(s) beside this symbol indicate
the vehicle’s heading direction (e.g. N for
north).
1Select “Options” on the map screen.
2Select “Map Mode” .
3Select the desired configuration but -
ton.
ORIENTATION OF THE MAP
The orientation of the map can be
changed between 2D north-up, 2D
heading-up and 3D heading-up by se-
lecting the orientation symbol dis-
played at the top left of the screen.
SWITCHING THE MAP MODE
No.FunctionPage
Select to display the single
map screen. 185
Select to display the dual
map screen.185
Select to display the com-
pass mode screen.186
Select to display the turn list
screen.216
Select to display the free-
way exit list screen.214