2016 SUBARU FORESTER display

Customizing functions
80
●Warning volume setting
The warning volume can be set to
Max/Mid/Min.
When the RES/+ or SET/- switch is pressed,
the setting will change to the next and 3 short
beeps will sound in the volume corresponding
to the setting.
●Lead vehicle acquisition alert setting
The lead vehicle acquisition alert function
setting can be activated or deactivated.
When the RES/+ or SET/- switch is pressed,
the setting will change to the next. When the
setting is changed to be activated, a short
beep will sound. When the setting is changed
to be deactivated, no beeps will sound.
●Lead Vehicle Start Alert setting
The Lead Vehicle Start Alert function setting
can be activated or deactivated.
When the RES/+ or SET/- switch is pressed,
the setting will change to the next. When the
setting is changed to be activated, a two-tone
beep will sound. When the setting is changed
to be deactivated, this function is turned off
and no beeps will sound.
NOTE
Even when the engine is restarted after the ignition switch is placed in the
LOCK (OFF) position, the setting will be restored to the previous status
before the ignition switch is placed in the LOCK (OFF) position.
S00869
Setting
Max
Mid
MinDisplay
S00870
Setting
Activate
Deactivate
Display
S00871
Setting
Activate
Deactivate
Display

List of the pop-up screens on the multi function display
81
List of the pop-up screens on the multi function display
If an EyeSight warning or malfunction is detected, a pop-up screen will be displayed on the
multi function display. Depending on the message, a buzzer will sound at the same time.
If a pop-up screen is displayed, refer to the
pop-up screen list and take the appropriate
action. Display screen 1 and display screen 2
will appear in order. While the mark is
illuminated, pull the (information)/SET
switch to indicate the pop-up screen again.
■Screen list (warning indicator, etc.)
Item Displayed screen mark Action (Reference page)
The “brake more”
warning
For Canada: MFD
For USA: on the meter
display
None
Refer to page 42.
Pre-Collision Braking
System
Refer to page 43.
Pre-Collision Throttle
Management
Refer to page 52.
Lane Departure
Warning
For Canada: MFD
For USA: on the meter
display
None Refer to page 58.
Normal screen Normal screenPop-up screenMark
S00912
EyeSight
Check Manual
8:32FF
MPGMPG
miles
F
MPGMPG
miles
S00873
S00874
Obstacle Detected
S00875
Lane Departure

List of the pop-up screens on the multi function display
82
Item Displayed screen mark Action (Reference page)
Lane Sway Warning
For Canada: MFD
For USA: on the meter
display
None Refer to page 61.
Lead Vehicle Start Alert None
Refer to page 64.
Conventional Cruise
ControlNone
Refer to page 68.
Automatic cancellation
by the systemNone
Refer to page 38.
None
Refer to page 38.
None
Refer to page 38.
S00876
Stay Alert
S00877
Vehicle Ahead Has Moved
S00878
Cruise Control
S00879
OFF
S00880
No Lead VehicleOFF
S00881
Steep GradeOFF

List of the pop-up screens on the multi function display
83
■Screen list (Malfunction, temporary stop, etc.)
*Depending on the location of malfunction, will blink or illuminate.Item Displayed screen mark Action (Reference page)
EyeSight System
Malfunction*Yes
(yellow)
Refer to page 76.
EyeSight system
temporary stopNone
Refer to page 77.
None
Refer to page 78.
None
Refer to page 78.
S00859
EyeSight off
Check Manual
S00862
EyeSight Disabled
No Camera View
S00864
EyeSight Disabled
Temp Range
S00866
EyeSight Disabled
Check Manual

84
Troubleshooting
Cruise control cannot be set.
Did you remember to press the (CRUISE) switch?
If you have not pressed the (CRUISE) switch, the (Adaptive Cruise
Control) indicator will not be shown.
Is EyeSight operation temporarily stopped?
When EyeSight is temporarily stopped, one of the EyeSight temporary stop indi-
cators (“E1”, “E2” or “E3”) will be displayed on the data display.
Set cruise control again after the reason for the temporary stop has been cor-
rected.
Is the [READY] indicator displayed?
When Adaptive Cruise Control is being used Cruise control cannot be set when
the [READY] indicator is not displayed. Set cruise control when the [READY] indi-
cator is displayed.
The [READY] indicator is not displayed.
Have you selected Conventional Cruise Control?
With Conventional Cruise Control, (following distance setting) will not be dis-
played on the meter display.
Are the requirements for setting cruise control met?
In any of the following cases, the [READY] indicator will not be displayed.
xThe brake pedal is depressed.
xThe vehicle speed is over 90 MPH (145 km/h). (When no vehicle in front
has been detected, the speed is between approximately 25 MPH (40 km/h)
and 90 MPH (145 km/h).)
xThe meter display indicates that the shift position indicator is in any posi-
tion other than . (The select lever or paddle shift switches are manually
operated.)
xThe driver’s seatbelt is unfastened.
xAny door of the driver’s, front passenger’s and rear doors is opened.
xThe parking brake is applied (when the brake warning light is illuminated).
xThe vehicle is on a steep grade.
xThe steering wheel is turned significantly in either direction.
xVehicle Dynamics Control is off, or is turned off.
xThe X-mode is turned on. (The X-mode indicator illuminates.)
D