Page 9 of 32
›Climatronic - Operation of the rear bench seat
Individual functions can be set or switched on by pressing the appro-
priate button. When the function is activated, the warning light illumi-
nates in the button.
Left rear seat heating
Lower the temperature
Display of the set temperature
Increase the temperature
Right rear seat heating
ABC› Manual air conditioning
Individual functions can be set or switched on by turning the control
dial or by pressing the appropriate button. When the function is activa-
ted, the warning light illuminates underneath the button.
Setting temperature
Adjust the blower speed
Set the direction of the air outlet
Seat heater on the front left seat Cooling system
Heated rear window Recirculated air mode
Depending on equipment fitted:
Auxiliary heating
Heated windscreen
Seat heating for the front right seat
ABCD7
Page 10 of 32
Instrument cluster›Buttons/dials on the multifunction steering wheel
Operating the multifunction display
Turn - select data / set values
Press - display / confirm indication
Operating the MAXI DOT display Hold - display main menu
Press - return to a previous level in the menu
Turn - move in the selected menu
Press - confirm selected menu item
Other functions Switch on/off voice control
Turn - sets the volume
Press - sound on/off
Skip to next track/station
Switch to previous track/station
Display the assistance systems menu
Press - display the telephone menu, accept/end the call; select
contact
Hold - repeat last call, reject call
BBA›Buttons on the operating lever
Operating the multifunction display
Press (up or down) - select data / set values
Press - display / confirm indication
Operating the MAXI DOT display Hold (up or down) - display main menu
Press (up or down) - move to the selected menu
Press - confirm selected menu item
ABAB8
Page 11 of 32
›Setting the time›
Switch-on the ignition.›Press and hold the button
until the
Time
is shown in the
display.
› Release the button and the
system switches to the hour
setting function.›
Press the button again and set
the hours.
›
Wait 4 seconds, the system
switches to the minutes set-
ting.
›
Press the button again and set
the minutes.
›
Wait 4 seconds, the system
switches to the initial setting.
› Show the next service appointment›
Switch-on the ignition.›Press and hold the button
until the
Service
menu item is
shown in the display.
› Release the button, the remain-
ing kilometres or miles and days
are shown on the display until
the next service interval for 4 s.9
Page 12 of 32
Starting and stopping the engine›Key
Switching on the ignition
›
Turn key to position
2
.
Starting the engine - Automatic transmission
›
Press the brake pedal and turn the key into the position
3
.
Starting the engine - Manual transmission
›
Press the clutch pedal and turn the key into the position
3
.
Switch off the engine and ignition
›
Turn key to position
1
.
› Starter button
Switching on the ignition
›
Press the
button briefly.
Starting the engine - Automatic transmission
›
Briefly press the brake pedal and the button
.
Starting the engine - Manual transmission
›
Briefly press the clutch pedal and the button
.
Switch off the engine and ignition
›
Press the
button briefly.
10
Page 13 of 32
›START STOP system The basic idea of the START-STOP system is to always turn the engine
off when it does not need to be running. This feature is particularly ad-
vantageous in city traffic, where this significantly reduces fuel con-
sumption and thereby also considerably reduces vehicle running
costs .
When stopping the vehicle, an automatic engine cut-off takes place,
the warning light appears in the instrument cluster.
When starting up, the automatic start procedure takes place again.
Automatic shutdown / startup on vehicles with manual
transmission
The engine is switched off as soon as the vehicle comes to a halt, the
shift lever is moved into neutral and the clutch pedal is released.
The engine is started as soon as the clutch pedal is depressed.
Automatic shutdown / startup on vehicles with automatic
transmission
The engine is switched off as soon as the vehicle comes to a halt and
the brake pedal is operated.
The motor is started as soon as the accelerator pedal is depressed or,
if the Auto Hold function is deactivated, when the brake pedal is re-
leased.
Functional prerequisites of the START-STOP system
So that an automatic engine shutdown takes place when stopping and
then an automatic start-up process during start-up, the following con-
ditions must be met.
The driver's door is closed.
The driver has fastened the seat belt.
The driving speed was higher than 4 km/h after the last stop.Other conditions cannot be influenced or detected, these are subject
to the state of various vehicle systems and weather conditions. For
this reason, the START-STOP system may react differently in situa-
tions which seem identical from the driver's perspective.
If the conditions for shutdown are not met when the vehicle stops,
then no engine shutdown takes place, the warning light appears in
the instrument cluster.
If, when an engine is in automatic shutdown, START-STOP system de-
tects that the engine running is essential (e.g. As in the event of an
overloaded vehicle battery), then a premature automatic startup takes
place.
Deactivation of the START-STOP system
The START-STOP system can be temporarily deactivated, by pressing
the button in the front centre console. After switching the ignition
off and on, re-activation of the START-STOP system always takes
place.
Special conditions
Under certain circumstances, the vehicle can react more slowly than
usual to sudden acceleration, e.g. If the accelerator pedal is depressed
at the time of the automatic engine shutdown.11
Page 14 of 32
Braking and parking›Electric parking brake
Switching on
›
Pull on the
button.
The symbol
in the button comes on.
Manual shut-down
›
Press the brake pedal and press the
button.
The symbol
in the button is no longer illuminated.
Automatic shut-off
During start-up, the brake is automatically switched off.
› Auto Hold function
The Auto Hold function stops the vehicle rolling away during start up.
The safety of the system is displayed by the warning light
lighting
up in the instrument cluster.
Operating conditions The driver's door is closed.
The engine is running (or has been switched off automatically by
the START-STOP system).
In the case of automatic transmission, the selector lever is not in
position N.
If the driver’s door is opened or the ignition is switched off in a vehicle
which has been secured with Auto Hold, then the parking brake se-
cures the vehicle against unwanted braking.
Then,
is extinguished and
illuminates.
Activate/deactivate the function
Activation/deactivation takes place by pressing the button
.
When the function is activated, the symbol illuminates in the but-
ton.
12
Page 15 of 32
Park Assist systems›Parking aid
The system draws attention to obstacles in the vicinity of the vehicle
via audible signals and coloured labels in the Infotainment screen.
An obstacle at a distance of less than 30 cm
There is an obstacle in the road
A
(the distance to the obstacle
is greater than 30 cm)
An obstacle is located outside of the road
A
(the distance to the
obstacle is greater than 30 cm)
For vehicles only with sensors built into the rear bumper, the system
activation takes place by engaging reverse gear.
For vehicles with sensors built into the front bumper, system activa-
tion by engaging reverse gear, by pressing the button
in the front
centre console or automatically when the vehicle approaches an ob-
stacle at a speed below 10 km/h, when driving forwards.
› Reversing camera
For cars with a reversing camera, the area behind the vehicle and the
following orientation lines are displayed in the Infotainment screen
when reversing.
Distance about 40 cm (safety distance limit)
Distance about 1 m
Distance about 2 m
The lane lines terminate approximately 3 m behind the vehicle
System activation takes place by engaging reverse gear or by pressing
the button
in the front centre console.
ABCD13
Page 16 of 32
›Park Assist
Park Assist helps drivers park in suitable parallel and perpendicular
parking places or also to manoeuvre out of parallel parking spaces.
The system takes over the steering movements only when parking or
leaving a parking space. The driver operates the pedals and the shift
lever/gear selector.
Searching for a parking space
›
Slowly drive past a row of parked vehicles.
›
Press the
button.
If the system finds a suitable parking space, the note for parking is dis-
played in the instrument cluster.
If the system detects that the parking space found is suitable for par-
allel and transverse parking, a parking method is recommended in the
display and offers the option to change the parking method.
Press the button
to change the parking method (parallel/ transverse
parking).
A display example of the instructions for parallel parking (displaying
the instructions for the transverse parking takes place in the same
way).
Parking space recognised with the information to drive on
Parking space recognised with the information to reverse
Note for driving forwards
Note for reversing
14
