2016 SKODA FABIA Owner's Manual

Setting the armrest heightFig. 55
Raising the armrest
Read and observe on page 62 first.
›
To Adjusting the height , lift the armrest in the direction of the arrow into
one of the six locking positions » Fig. 55.
›
To fold down , lift the armrest in the direction of the arrow up to the stop and
then fold back down again.
Rear seats
 Introduction
This chapter contains information on the following subjects:
Seat backrests
63
Rear seat
64
Seat backrests
Fig. 56
Fold seat backrest forwards / standby position of the seat belt
Before folding the seat backrests forwards, adapt the position of the front
seats in such a way that they are not damaged by the folded seat backrests.
Folding forward›
Push the headrest into the seat backrest up to the latch.
›
Pull the outer seat belt to the side panel in the direction of arrow
1
» Fig. 56 .
›
Push the release lever
A
in the direction of arrow
2
and fold down the seat
backrest in the direction of arrow
3
.
Withthe undivided backrest, the two external security belts must be pulled to-
wards the side panel and the release handles
A
to press on both sides of the
backrest simultaneously.
Folding backwards
›
Pull the outer seat belt to the side panel in the direction of arrow
1
» Fig. 56 .
›
Raise the seat backrest against the direction of arrow
3
until the release
handle
A
audibly locks. Check this by pulling on the seat backrest.
›
Make sure that the red pin
B
is hidden.
In the undivided seat back, pull the two outer belts to the side panel. After
folding back the backrest, the release handles
A
should audibly click into
place on both sides of the backrest and the red mark
B
should not be visible
on either side of the backrest.
WARNING■ The seat backs in occupied rear seats must be properly engaged.■When transporting objects in the luggage compartment that has been en-
larged by folding the backrest forward, ensure the safety of the passengers
transported on the other rear seats.■
The seat backrests must be securely latched in position so that no ob-
jects from the luggage compartment can slip into the passenger compart-
ment under sudden braking – risk of injury.
CAUTION
When moving the seat backrest the seat belts should not be trapped - there is
a risk of damage to the seat belts.
Note
The belt tongue of the outer seat belts C can be inserted into the side panel.
Ready position » Fig. 56.63Seats and headrests

Rear seat
Applies to the Fabia EstateFig. 57
Fold rear seat forward / remove split rear bench seat
Fig. 58
Fold the rear seat back
The luggage space can be increased by folding the rear seat forward and re-
moving it.
For vehicles with split rear seats, the parts of the rear seat can be folded for-
ward individually and removed.
›
To fold , pull up the bench in the direction of arrow
1
and fold down in arrow
direction
2
» Fig. 57 .
›
To Remove , press the wire clamps in the direction of arrows
3
so that they
become detached from the holders, and remove the seat.
›
To use , press the wire clamps in the direction of arrows
3
and insert it into
the brackets.
›
To open , lift the armrest in the direction of arrow
4
» Fig. 58 .
›
Place the rear seat on the eyelets
A
, so that the eyelets
A
click into the
recesses in the plastic caps for 
B
.
WARNINGThe rear seat may not be pulled in under the eyelets A when folding back.
The rear seat could not be properly secured.
CAUTION
The rear seat must not be pulled in under the eyelets A when being folded
back - there is a risk of damaging the rear seat.
Headrests
 Introduction
This chapter contains information on the following subjects:
Setting the height
64
Removing/inserting
65
Note
■ The middle rear headrest is only adjustable in two positions.■In sports seats, the headrests are integrated into the seat backrests and can-
not be adjusted in height.
Setting the height
Fig. 59
Setting the height of the back headrest
Height adjustment of the headrests is the same in the front and rear.
›
Grasp the headrest and move upwards in the direction of arrow
1
» Fig. 59 .
›
To move the headrest down, press the securing button
A
in the direction of
arrow
2
and hold it down while pressing the headrest in the direction of ar-
row
3
.
64Operation

Removing/insertingFig. 60
Removing/instaling the headrest
The removal and installation of headrests is the same in the front and rear.
›
Before removing/installingthe headrests, fold the corresponding seat back-
rest slightly forward » page 63.
›
To remove the headrest, pull it out of the seat backrestup to the latch.
›
Press locking button
A
in the direction of arrow
1,
and pull out the head re-
straint in the direction of arrow
2
» Fig. 60 .
›
To insert the headrest, push the headrest into the seat backrest in the direc-
tion of arrow
3
until the locking button clicks into place.
Front seat heater
Fig. 61
Buttons for front seat heater
The seat backrests and seats can be heated electrically.
Seat heating buttons » Fig. 61
Left seat heating
Right seat heating
›
To turn on the heater at maximum heat (level 2) press button
 or
.
By repeatedly pressing the button, the heat is turned down until it is com-
pletely switched off . The level of the seat heater is indicated by the number of
illuminated warning lights in the switch.
The seat heating only operates when the engine is running.WARNINGIf you are sensitive to pain and/or temperature, e.g. through medication,
paralysis or because of chronic illness (e.g. diabetes), we recommend not to
use the seat heating. If the seat heater is used, we recommend to make
regular breaks in your journey when driving long distances, so that the
body can recuperate from the stress of the journey. Please consult your
doctor, who can evaluate your specific condition.
CAUTION
The following instructions must be observed to avoid damage to the seats.■Do not kneel on the seats or otherwise apply concentrated pressure to them.■
Do not switch on the heating for unoccupied seats.
■
Do not switch on the heating for seats which have objects on them (e.g. a
child seat, bag or similar).
■
Do not switch on the heating for seats which have seat covers or protective
covers on them.
Note
■ If the heaters for the rear seats are set to their highest intensity (level 2),
they are automatically switched down to level 1 after 10 minutes.■
If the on-board voltage decreases, the seat heating switches off automati-
cally » page 142 , Automatic shutdown of consumers - vehicle battery dis-
charge protection .
65Seats and headrests

Useful features
Interior fittings
Introduction
This chapter contains information on the following subjects:
Ticket holder
66
Storage compartments in the doors
67
Storage compartment in the front centre console
67
USB and AUX input
67
Coin and card holders
67
Storage compartment on the dash panel
68
Cup holders
68
Waste container
68
Cigarette lighter
69
Ashtray
69
12-volt power outlet
70
Multimedia holder
70
Storage compartment in the front arm rest
71
Glasses compartment
71
Storage compartment on the front passenger side
71
Storage compartment on the side of front seat
72
storage compartment under the passenger seat
72
Storage compartment for umbrella
72
Clothes hook
72
Storage pockets on the backs of the front seats
73
Storage pockets on the inner sides of the front seats
73
Storage compartment in the rear centre console
73WARNING■ Do not place anything on the dash panel. These objects might slide or fall
down when driving and may distract you from concentrating on the traffic –
risk of accident!■
Make sure that while driving no objects can enter the driver's footwell -
they could cause an accident!
WARNING (Continued)■ Do not transport any objects on the front passenger seat other than ob-
jects intended for this purpose (e.g. child safety seat) – risk of accident.■
No objects should be placed in the storage compartments nor in the
drinks holders; the vehicle occupants could be endangered if there is sud-
den braking or the vehicle collides with something.
■
For safety reasons, lockable storage compartments should be closed
while driving - there is a risk of injury from the opened lid or through the
loose objects in the compartment.
■
Make sure no objects protrude from the storage compartments - There is
a risk of injury!
■
Do not exceed the permissible loads for the storage compartments and
pockets - risk of injury and risk of damage to the compartments and pock-
ets!
■
Ash, cigarettes, cigars etc. should only be stored in the ashtray - danger
of fire/burns!
■
The storage compartments, multimedia holder and waste container are
not a substitute for the ashtray and must not be used for such purposes –
risk of fire!
CAUTION
Do not place any large or sharp objects in the storage compartments and pock-
ets - there is a risk of damage to the compartments and pockets.
Ticket holder
Fig. 62
Ticket holder
Read and observe and on page 66 first.
The ticket holder » Fig. 62 is provided for the holding and displaying e.g. car
park tickets.
66Operation

Storage compartments in the doorsFig. 63
Storage compartments: in the front door/in the rear door
Read and observe
and on page 66 first.
Storage compartments » Fig. 63
Storage compartment
Bottle holder with a capacity of max. 1.5 l
Bottle holder with a capacity of max. 0.5 l
The reflective vest can be stowed in the storage compartments in the
door » page 149 .
WARNINGThe storage compartmentA » Fig. 63 is to be used exclusively for storing
objects which do not stick out - danger of restricting the effectiveness of
the side airbags.
Storage compartment in the front centre console
Fig. 64
Storage compartment
ABCRead and observe and on page 66 first.
The open storage compartment is in the front of the centre console » Fig. 64.
USB and AUX input
Fig. 65
USB and AUX inputs
Read and observe and on page 66 first.
The USB input (with
 in) and AUX input (with
 in) are located above the
storage compartment in the front centre console » Fig. 65.
Information on use » Owner's Manual Infotainment .
Coin and card holders
Fig. 66
Coin and card holders
Read and observe and on page 66 first.
The coin holder
A
and card holder
B
are located in the front centre console
» Fig. 66 .
67Useful features

Storage compartment on the dash panelFig. 67
Storage compartment
Read and observe and on page 66 first.
The storage compartment is located in the middle part of the panel » Fig. 67.
Cup holders
Fig. 68
Cup holder
Read and observe and on page 66 first.
Two beverage containers can be placed into the cup holder » Fig. 68.
WARNING■
Do not use cups or beakers made of brittle material (e.g. glass, porcelain).
This could lead to injuries in the event of an accident.■
Never put hot beverage containers in the cup holder. They may spill as
the vehicle moves – there is a risk of scalding.
CAUTION
Do not leave open beverage containers in the cup holder during the journey.
There is a risk of spilling e.g. when braking which may cause damage to the
electrical components or seat upholstery.Waste containerFig. 69
Waste container: inserting and moving/opening
Fig. 70
Replace bags
Read and observe
and on page 66 first.
The waste container can be inserted into the slot in the door.
Insert waste container
›
Position the waste container at the front edge of the slot.
›
Push the waste container to the back in the direction of the arrow
A
» Fig. 69 .
›
Push the waste container as required in the direction of arrow
B
.
Remove the waste container
›
Remove the waste container in the opposite direction to the arrow
A
» Fig. 69 .
Open / close waste container
›
Lift the lid in the direction of arrow
C
» Fig. 69 . 
68Operation

Closing takes place in reverse order.
Replace bags›
Remove the waste container from the slot.
›
Press the two locking lugs on the frame in the direction of arrow
1
» Fig. 70 .
›
Pull the bag together with the frame down in the direction of arrow
2
.
›
Remove the bag from the frame.
›
Pull the new bag through the frame and pull it over the frame in the direction
of arrow
3
.
›
Place the bag with the frame in the direction of arrow
4
into the container
body, so that the two lugs engage audibly on the frame.
Note
We recommend that you use 20x30 cm bags.
Cigarette lighter
Fig. 71
Cigarette lighter
Read and observe and on page 66 first.
›
To use the lighter, push it in as far as the stop and wait until the glowing
lighter clicks out again » Fig. 71.
›
Take out the glowing lighter instantly, use it and insert it back into the sock-
et.
WARNING■ The cigarette lighter also works if the ignition is switched off. When leav-
ing the vehicle, never leave people who are not completely independent,
such as children, unattended in the vehicle - there is a risk of burning, fire
or damage to the vehicle interior.■
Be careful when using the cigarette lighter - It can cause burns.
NoteThe cigarette lighter socket can also be used as a 12-volt socket.
Ashtray
Fig. 72
Removing ashtray and opening
Read and observe and on page 66 first.
The ashtray can be used for disposing of ash, cigarettes, cigars and the like etc
›
Remove the ashtray in the direction of the arrow
A
» Fig. 72 .
›
To the Openturn the ashtray cover in the direction of arrow
B
.
Closing takes place in reverse order.
WARNINGNever place hot or flammable objects in the ashtray – risk of fire!69Useful features

12-volt power outletFig. 73
12-volt power outlet cover: the middle part of the panel / in the
luggage compartment
Read and observe
and on page 66 first.
›
Touse , remove the cover of the socket » Fig. 73 -
 or open the cover of the
socket » Fig. 73 -
 .
›
Connect the plug for the electrical appliance to the socket.
WARNING■
Do not place anything on the dash panel. These objects might slide or fall
down when driving and may distract you from concentrating on the traffic –
risk of accident!■
Make sure that while driving no objects can enter the driver's footwell -
they could cause an accident!
■
Stow all devices safely during the journey to prevent them from being
thrown around the interior in the event of a sudden braking manoeuvre or
an accident – The is a risk of death!
■
The devices may warm up during operation – The is a risk of injury or fire!
■
Improper use of the power sockets and the electrical accessories can
cause fires, burns and other serious injuries.
■
The sockets also work if the ignition is switched off. When leaving the ve-
hicle, never leave persons who are not completely independent, such as
children, unattended in the vehicle.
CAUTION■ The sockets can only be used for the connection of approved electrical ac-
cessories with a total power consumption of up to 120 watts - otherwise the
electrical system of the vehicle may be damaged.■
Connecting appliances when the engine is not running will drain the battery
of the vehicle!
■
Before switching the ignition on / off or before starting the engine, switch
off the devices which are connected to the sockets - there is a risk of damage
to the equipment due to voltage fluctuations.
Multimedia holder
Fig. 74
Multimedia holder
Read and observe and on page 66 first.
Multimedia holder » Fig. 74
Storage compartment for storing the vehicle key
Storage compartment for storing two coins
Storage compartment for storing a mobile phone
ABC70Operation