2016 Seat Ibiza ST Owner's manual

Fuses and bulbs
– Unc lip the r
etainer s
pring ››› Fig. 100 3 pressing inwards to the right.
– Extract the bulb and fit the replacement so
th at
the lug on the b a

se fits into the recess
on the reflector.
– Fit the connector.
– Fit the cover and close the strap. Make sure
that the ga

sket sits well on the casing cover
during the operation.
– Check whether the new bulb is working.
Turn signal light Fig. 101
Turn signal light. –
Raise the bonnet.
– Turn the bulb holder ››
›
Fig. 101
1 to the
l ef t
and p
ull. –
Remove the b
ulb by pressing on the bulb
holder and turning it anti-clockwise at the
same time.
– Installation involves all of the above steps
in reverse sequenc

e.
Changing the AFS headlight
bulb
s
Position of the bulbs Fig. 102
AFS headlight bulbs. Turn signal
X
enon he
adlight

(dipped beam/main
beam)
A B Changing the xenon bulb
The procedure for changing the bulb is the
same on both side
s

of the vehicle. WARNING
This type of bulb should be changed at a spe-
cia li

sed workshop. Turn signal bulb
Fig. 103
Turn signal light. –
Raise the bonnet.
– Turn bulb holder ››
›
Fig. 103
A to the left
and p u
ll
.
– Remove the bulb by pressing on the bulb
holder and turnin

g it anti-clockwise at the
same time.
– Installation involves all of the above steps
in reverse sequenc

e.
87
Technical data
Advice
Operation
Emergencies
Safety

Emergencies
Changing the fog light bulbs Fr ont
fog light
bulbFig. 104
Front fog light. Fig. 105
Front fog light. –
Remove the bolt ››
›
Fig. 104
1 from the fog
light gri
ll
e with a screwdriver.
– Subsequently, remove the clips located on
the edge of the gril

l with gentle leverage. –
Remove the 3 bo
lts ››› Fig. 105 2 to re-
mo v
e the f og light
.
– Remove the metal clip situated on the up-
per part of

the fog light by pulling towards
the exterior of the vehicle ››› Fig. 105 3 .
FR version fog-light bulb Fig. 106
Fog light: access to the connector
and t o the light
bu

lb holder. –
Remove the 4 bolts A
› ›
› Fig. 106 fr

om the
inside of the wheel housing and the 2 bot-
tom bolts B
› ›
› Fig. 106 fr

om the bumper
with a screwdriver.
– Pull the bumper to release it from its an-
chorage

s to access the connector and the
light bulb holder. Note
Due to the difficulty of accessing fog light
bul b

s, have them replaced at a Technical
Service or specialised workshop. Remove the bulb holder
Fig. 107
Front fog light. –
Remove connector ››
›
Fig. 107
1 from the
b u
lb
.
– Turn the bulb holder ››› Fig. 107
2 to the
l ef
t and p
ull.
– Remove the bulb by pressing on the bulb
holder and turnin

g it counter-clockwise at
the same time.
– Installation involves all of the above steps
in reverse sequenc

e.
– Check that the bulb works properly.
88

Fuses and bulbs
Changing the tail light bulbs S umm
ary
of LED tail lights3 Applies to the model: IBIZA/IBIZA SC
LED
● Brak e lights
● Side lights
B

ulb
s
● Retro fog light
● Reverse lights
● Turn signal
Tail light summary 3 Applies to the model: IBIZA ST
T ai

l lights on side panel Bulb lamps
● Brake lights
● Side lights
● Turn signal
Lights on the r e

ar lid Bulb lamps
● Reverse lights
● Side lights
● Fog lights Tail lights on side panel LED lamps
●
Brake light (LED)
● Side light (LED)
● Turn signal
Lights on the re
ar lid LED lamps
● Reverse lights
● Side light (LED)
● Fog lights
Access to tail lights 3 Applies to the model: IBIZA/IBIZA SC
Fig. 108
Access to tail lights. ●
Open the rear lid.
● Turn the bolt in the direction of the arrow,
b y
h and or w

ith a screwdriver ››› Fig. 108.
● Remove the tail light, by pulling it out-
wards. Ch

anging the tail light bulbs 3 Applies to the model: IBIZA/IBIZA SC
Fig. 109
Changing the tail light bulbs Fig. 110
Changing the tail light bulbs ●
Remove the connector from housing A ›››
Fig. 108. »
89
Technical data
Advice
Operation
Emergencies
Safety

Emergencies
● Remo
ve the b
ulb holder, separating it from
the casing. To do this, press tabs B in the
dir ection of
the arro
ws ››› Fig. 109.
● When the bulb holder has been removed,
press
in the direction of the arrow 1 and at
the s ame time, t
urn in the dir ection of
the ar-
row 2
› ››
Fig. 110
Ch angin

g bulbs. LED lamps
Carry out the same operations as in lights fit-
ted with bulbs.
If necessary, remove the socket, as if it were
a bulb.
If the brake light and/or side light with LEDs
have to be replaced, the tail light must be re-
placed. Changing the tail light bulbs (on the
side panel) 3 Applies to the model: IBIZA ST
Fig. 111
Lights on the side. Fig. 112
Removing the bulb holder. Accessing the side light bulbs
● Open the rear lid.
● Look for a lid with a grill behind the side
lights. ●
Remo
ve the lid w

ith a flat screwdriver, plac-
ing it in notch A
› ››
Fig. 111
.
Ch an
ging bulbs
● Remove the bulb holder by pressing the
fast
ening clip B
› ››
Fig. 112
and pu
lling it
outwards.
● Replace the faulty bulb, rotating it to the
left and outw
ards.
● To refit follow the steps in reverse order,
taking s
pecial care when fitting the bulb
holder.
Changing bulbs. LED lamps
Carry out the same operations as in lights fit-
ted with bulbs.
If necessary, remove the socket, as if it were
a bulb.
If the brake light and/or side light with LEDs
have to be replaced, the tail light must be re-
placed.
90

Fuses and bulbs
Changing the tail light bulbs (on the
r e
ar lid) 3 Applies to the model: IBIZA ST
Fig. 113
Lights on the boot. Fig. 114
Removing the bulb holder. Accessing the rear lid lights
● Open the rear lid.
● On the rear lid lining there is a lid behind
e ac
h light . ●
R emove the lid w

ith a flat screwdriver, plac-
ing it in notch A
› ››
Fig. 113
.
Ch an
ging bulbs
● Remove the bulb holder by pressing the
fast
ening clips B
› ››
Fig. 114
and pu
lling
outwards.
● Replace the faulty bulb, rotating it to the
left and outw
ards.
● To refit follow the steps in reverse order,
taking s
pecial care when fitting the bulb
holder.
Changing bulbs. LED lamps
Carry out the same operations as in lights fit-
ted with bulbs.
If necessary, remove the socket, as if it were
a bulb.
If the brake light and/or side light with LEDs
have to be replaced, the tail light must be re-
placed. Changing the side and interior
bulb

s
Turn signals Fig. 115
Turn signals. –
Press the turn signal to the left or to the
right t
o r emo

ve the bulb.
– Remove the bulb holder from the turn sig-
nal.
– Remo

ve the failed bulb and replace with a
new bulb
.
– Insert the bulb holder in the turn signal
guide until it

clicks into place.
– First fit the turn signal in the opening in the
chas

sis, fastening the tabs 1
› ›
› Fig. 115 ,
and then fit
in the bulb as shown by the ar-
row 2
› ›
› Fig. 115 .
91
Technical data
Advice
Operation
Emergencies
Safety

Emergencies
Number plate light 3 Applies to the model: IBIZA/IBIZA SC
– Inser t
the flat part of a screwdriver into the
special
slot and remove the bulb.
– Remove the bulb holder, by turning it until
it is fr

ee.
– Change the bulb.
– Replace the bulb holder, by turning it until
it fits fu

lly.
– Fit the light into the space and press until
you hear a “c lic

k”.
Number plate light 3 Applies to the model: IBIZA ST
Fig. 116
Remove the number plate light. –
Insert the flat part of a screwdriver into the
spec
ial

slot and remove the number plate
light from its moulding. –
Remove the c
onnector and extract the bulb.
After changing the bulb, fit the connector
again.
– Place the light in its moulding, pressing the
left s

ide. Once it is fitted into place, press
the right side until you hear a “click”.
Additional brake light* Given the difficulty involved in the replace-
ment of thi
s

light it should be done by Tech-
nical Services.
Interior light and front reading lights Fig. 117
Front reading light. To remove the glass
– Insert a fine screwdriver between the cas-
ing and the gl
as

s ››› Fig. 117. –
Carefu
lly remove the glass, levering it to
avoid possible damage.
To replace the bulbs
– Pull the bulbs outwards.
– To remove the central bulb, hold and press
to one side.
Assemb

ly
– Proceed in the reverse order, pressing gen-
tly on the outer edge of

the side light.
– First fit the glass with the fastening tabs
over the frame of

the switch. Next press the
front part until the two long tabs click on
the support.
92

Fuses and bulbs
Luggage compartment light* Fig. 118
Boot light. Fig. 119
Boot light. –
Extract the bulb by pressing on its inside
edg e -
arr o
w- using the flat side of a screw-
driver ››› Fig. 118.
– Press the bulb sideways and remove it from
its housin

g ››› Fig. 119.
93
Technical data
Advice
Operation
Emergencies
Safety

Operation
Fig. 120
Dash panel.94