2016 Peugeot Traveller tow

117
Traveller-VP_en_Chap03_ergonomie-et-confort_ed01-2016
Upper fixings
Lower fixings (behind row 1)
If your vehicle has fixed one-piece bench seats
or seats and bench seats: F
on each side in row 2, insert the fixings in the
floor anchorages then turn them a quarter turn
to lock them in place (as shown above).
Place them as close as possible to the end of the rail.
F unclip the anchorage cover in the roof on each side.
F
o
n e
ach side in row 2, insert the fixings in
the floor anchorages (as shown above). If your vehicle has seats and bench seats or
individual seats on rails
:
Lower fixings (behind row 2)
F use the stowing rings.
Fit the net
unclip the upper fixing covers and secure the
lower fixings (as previously described).
F

F
old (table position) the seats and bench
seats in rows 2 and 3 (according to
equipment).
F
u
nr
oll the high load retaining net.
F

P
osition the upper net fixings in the
corresponding anchorages in the roof
(first one side, then the other).
F

F
ully extend the straps.
F
o
n e
ach side, attach the bottom fixings of
the net to the lower anchorages (behind
row 1) or in the stowing rings (behind
row


2).
F

P
ull on the straps to stretch the net.
F

C
heck that the net is attached securely and
properly extended.
Never use the IS
oF

IX ring intended
for fixing the upper strap of a child seat
with Top Tether.
3
ease of use and comfort

122
Traveller-VP_en_Chap03_ergonomie-et-confort_ed01-2016
Unfolding
F Pull each table top fully up then pivot them on each side into the horizontal position. F

R
aise each table top, going beyond the
point of resistance, to the vertical position.
F
P
ush each table top down into its housing
until it clicks into place.
F
P
ush the control then tip the table
assembly downward until it clicks into
place.
Folding
Before stowing the table tops, check
that there is no object underneath.
Before tipping the assembly down,
check that the two table tops have
clicked home in the low position and
that there is nothing in the cup holder
area (such as a can or pen).
F
o
p

erate the control on the top and pull the
table assembly up until it clicks into place.
Cup holders
Liquids carried in an open vessel (a cup
or mug) could be spilt, presenting a risk.
Ta k e c a r e .
Never use the table in this position
while the vehicle is being driven.
Two cups or cans and small objects (such as
a credit card, portable ashtray or pen) can be
carried in the middle of the unfolded table.
ease of use and comfort

124
Traveller-VP_en_Chap03_ergonomie-et-confort_ed01-2016
Take care of passengers' feet when
manoeuvring the assembly.Incorrect use of the table could cause
serious injury.
Never use the table open or unfolded
while the vehicle is being driven. An
object on the table is turned into a
projectile under heavy braking.
en

sure that the table is correctly stowed
in the low position before moving off.
Never use the table tops as seats or
lean on them.
A label on the table is a reminder of this. Never place hot objects such as
casseroles or cooking pans on the
table, you risk damaging its surface
(risk of fire).
With the table deployed, each top can
support a maximum of 10 kg. Failure to
observe this maximum load introduces
the risk of damaging all or part of the
table module.
Never raise the table when it is between
individual seats; this risks damaging the
table tops.
Storage off the runner
If removing and storing the table
out of the vehicle, ensure that it is
placed in a clean area, so as to avoid
introducing any foreign bodies into the
mechanisms.
The table assembly must be placed on
a flat and level sur face when out of the
vehicle, resting on the guide so as to
avoid damaging the visible parts.
Caution, when out of the vehicle, the
table leans to the right or left when put
down.
ease of use and comfort

131
Traveller-VP_en_Chap03_ergonomie-et-confort_ed01-2016
Front demist - defrost
These markings on the control panel indicate the control positions for rapid demisting or
defrosting of the windscreen and side windows.
Manual air conditioning
With Stop & Start, when demisting has
been activated, the SToP mode is not
available.
Dual-zone digital air
conditioning
F Put the air flow, temperature and distribution controls to the dedicated
marked position.
The system automatically manages the air
conditioning, air flow and air intake, and
provides optimum distribution towards the
windscreen and side windows.
The system reverts to the previous settings. F
P ress this button to demist or
defrost the windscreen and side
windows as quickly as possible.
F

T
o stop, press this button again
or on "AUTO".
F

F
or air conditioning, press
this button; its indicator lamp
comes


on. Heated windscreen and washer jets
For more information on the Wiper
control stalk
and in particular the
heated windscreen and washer jets,
refer to the corresponding section.
3
ease of use and comfort

134
Traveller-VP_en_Chap03_ergonomie-et-confort_ed01-2016
In order for these systems to be fully effective, follow the operation and maintenance
guidelines below:
F
T
o obtain an even air distribution, take care not to obstruct the exterior air intake grilles
located at the base of the windscreen, the nozzles, the vents and the air outlets, as well
as the air extractor located at the rear.
F

D
o not cover the sunshine sensor, located at the top of the windscreen; this is used for
regulation of the air conditioning system.
F
o
p
erate the air conditioning system for at least 5 to 10 minutes, once or twice a month
to keep it in per fect working order.
F
e
n
sure that the passenger compartment filter is in good condition and have the filter
elements replaced regularly.
W

e recommend the use of a combined passenger compartment filter. Thanks to its
special active additive, it contributes to the purification of the air breathed by the
occupants and the cleanliness of the passenger compartment (reduction of allergic
symptoms, bad odours and greasy deposits).
F

T
o ensure correct operation of the air conditioning system, you are also advised to have
it checked regularly as recommended in the warranty and maintenance record.
F

I
f the system does not produce cold air, switch it off and contact a P
e
ugeo
T d
ealer or
a qualified workshop.
Recommendations for heating, ventilation and air conditioning
If after an extended stop in sunshine,
the interior temperature is very high, first
ventilate the passenger compartment for
a few moments.
Put the air flow control at a setting high
enough to quickly change the air in the
passenger compartment.
The air conditioning system does not
contain chlorine and does not present
any danger to the ozone layer.
The condensation created by the air
conditioning results in a discharge
of water under the vehicle which is
perfectly normal.
When towing the maximum load on a steep gradient in high temperatures, switching off the
air conditioning increases the available engine power and so improves the towing ability.
Stop & Start
The heating and air conditioning
systems only work when the engine is
running.
To maintain a comfortable temperature
in the passenger compartment, you can
temporarily deactivate the Stop & Start
system.
For more information on Stop & Star t ,
refer to the corresponding section.
Air vents
To close a vent, move the control
towards the outside of the vehicle. Slight
resistance may be felt.
ease of use and comfort

154
Traveller-VP_en_Chap04_eclairage-et-visibilite_ed01-2016
Wiper control stalk
Manual controls
The wipers are controlled directly by the driver.
Programming
Your vehicle may also include some functions
that can be configured:
-
a
utomatic rain sensitive windscreen wipers,
-
r

ear wiping on engaging reverse gear.
Windscreen wipers
Wiping speed control stalk: raise or lower the
stalk to the desired position.
Model with manual wiping
(intermittent)
Model with AUTO wiping
Fast wipe (heavy rain).
Normal wipe (moderate rain).
Intermittent wipe (proportional to the
speed of the vehicle).
Park.
Single wipe (press downwards or pull
the stalk briefly towards you, then
release).
orAutomatic wiping (press down,
then release).
Single wipe (pull the stalk briefly
towards you).
Do not operate the wipers on a dry
windscreen.
u
n

der extremely hot or
cold conditions, ensure that the wiper
blades are not stuck to the windscreen
before operating the wipers.
In wintry conditions, remove snow, ice
or frost present on the windscreen,
around the wiper arms and blades and
the windscreen seal, before operating
the wipers.
Lighting and visibility

156
Traveller-VP_en_Chap04_eclairage-et-visibilite_ed01-2016
If a significant accumulation of snow or
ice is present, or when using a bicycle
carrier on the boot, deactivate the
automatic rear wiper. This function is activated by default.
Reverse gear
When reverse gear is engaged, the rear wiper
will come into operation automatically if the
windscreen wipers are operating.
In the vehicle settings menu, activate/
deactivate "Rear wiper in reverse ".
With the audio system
In the "Personalisation-configuration " menu,
activate/deactivate " Rear wipe in reverse
gear ".
With the touch screen Activation / Deactivation
Activation or deactivation of the function is
done in the vehicle configuration menu.
F

P
ull the windscreen wiper stalk towards
you. The screenwash then the wipers
operate for a fixed period.
The headlamp wash is only activated if the
dipped headlamps are on and the vehicle is
moving .
With daytime running lamps, to activate the
headlamp wash, position the lighting stalk in
the dipped beam position.
Windscreen and headlamp
wash
on vehicles fitted with automatic
air conditioning, any action on the
windscreen wash control results in
temporary closing of the air intake to
avoid odours inside the passenger
compartment.
Screenwash/headlamp wash
level low
In the case of vehicles fitted with headlamp
washers, when the fluid reservoir low level
is reached this warning lamp comes on in
the instrument panel, accompanied by an
audible signal and a message.
The warning lamp comes on when the ignition
is switched on, or every time the stalk is
operated, until the reservoir is refilled.
Next time you stop, refill the screenwash /
headlamp wash reservoir.
Lighting and visibility

158
Traveller-VP_en_Chap05_securite_ed01-2016
Automatic operation of
hazard warning lamps
Hazard warning lamps
When braking in an emergency, depending on
the rate of deceleration, as well as when the
ABS regulation is invoked or in the event of an
impact, the hazard warning lamps come on
automatically.
They switch off automatically the first time you
accelerate.
F
Y
ou can also switch them off by pressing
the button.
Visual warning with all of the direction
indicators flashing to alert other road users to a
vehicle breakdown, towing or accident.
emergency or
assistance call
This system allows you to make an emergency
or assistance call to the emergency services or
to the dedicated P
e

ugeo
T s
ervice.
For more information on Audio
equipment and telematics and in
particular the use of this equipment,
refer to the corresponding section.
F

P

ress this button, all of the direction
indicators flash.
They can operate with the ignition off.
Safety