2016 Peugeot 308 instrument panel

175
308_en_Chap06_conduite_ed02-2015
Switching on / Pause
F turn thumb thumb wheel 1 to the "LIMIT"
p osition: the speed limiter mode is selected
but is not switched on (Pause).
F
Sw

itch the speed limiter back on by
pressing button 4 , if the speed displayed
is suitable (by default, the last speed
programmed).
F
Yo

u can temporarily stop the the speed
limiter by pressing button 4 again: the
display confirms that it has been stopped
(Pause). You do not have to switch the speed limiter on
in order to set the speed.
Once the function is selected, you can modify
the speed setting by:
-
us

ing buttons 2 and 3, increasing or
decreasing the speed displayed:
F
by s

uccessive short presses, to modify
by + or - ½ mph (1 km/h),
F
by a m

aintained press, to modify in steps
of + or - 3 mph (5 km/h). -
pr

essing button 5
:
F
th
e six speeds memorised are displayed
in the touch screen,
F
pr
ess the button corresponding to the
speed limit chosen
the v
alue is displayed in the instrument
panel.
the s
election screen closes after a
few moments.
Adjusting the speed limiter
setting
6
Driving

177
308_en_Chap06_conduite_ed02-2015
Steering mounted controls
6. Cruise control pause / resume indication.
7. Cr uise control mode selection indication.
8.
Speed

value setting.
Cruise control
System which automatically maintains the speed of the vehicle at the value programmed by the driver, without any action on the accelerator pedal.
the cruise control system cannot, in any circumstances,
r eplace the need to observe speed limits, nor can it
replace the need for vigilance on the part of the driver.
You are advised to keep your feet near the pedals at
all times.
the cruise control is switched on m anually: it
requires a minimum vehicle speed of 25 mph
(40 km/h).
1.
Selec

t cruise control mode.
2.
De

crease value or speed setting on the fly.
3.
In

crease value or speed setting on the fly.
4.
Pa

use / resume cruise control.
5.
Dis

play the list of memorised speeds.Displays in the instrument panel
Switching off the ignition cancels any
programmed speed value.
the c

ruise control is paused
manually or
by pressing the brake or clutch pedal or
on triggering of the
eS
C system for safety
reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal.
to re

turn to the programmed speed, simply
release the accelerator pedal until the
programmed cruise speed is reached again. With a manual gearbox, third or fourth gear
(depending on engine) or higher must be
engaged.
For more information on memorising speeds,
refer to the corresponding section.
With an automatic gearbox, second gear or
higher must be engaged.
6
Driving

178
308_en_Chap06_conduite_ed02-2015
Switching on
If the cruise control is switched on, you can then
modify the initial speed in one of the following ways:
- using buttons 2 o r 3:F by successive short presses, to modify the
s peed by + or - 1 mph (km/h),
F by a long press, to modify the speed in steps
o f + or - 5 mph (km/h),
Pause
F turn wheel 1 to the "CRUISE" p osition: the
cruise control mode is selected but is not
switched on (Pause).
F
Pr

ess button 2 or 3 : your vehicle's current
speed becomes the cruise speed.
the c

ruise control is activated (ON).
Modification of the initial
speed setting
- pressing button 5 :
F th e six memorised speeds are displayed
in the the touch screen,
F
ch

oose a value: it is displayed in the
instrument panel.
the s

election screen closes after a few
moments.
the m

odification is then accepted. Once switched on, you can pause the cruise
control at any time by pressing button 4: the
screen confirms the pause.
Driving

182
308_en_Chap06_conduite_ed02-2015
the active cruise control must be selected in
t he " Driving assistance " menu.
F


t
ur
n the wheel 1 to the " CRUISE" position:
cruise control mode is selected, but not
started (Pause).
F
Pr

ess one of the buttons 2 or 3 : the current
speed of your vehicle becomes the cruise
speed setting.
the c

ruise control is activated (ON).
By default, the inter-vehicle time is set at
2
se

conds.
Otherwise, the last setting made will be used
when switching on the system.
Switching on
6. Indication of cruise control pause/resume.
7. In dication of selection of cruise control
mode, or
ve

hicle speed adjustment phase.
8.
Cr

uise speed setting.
Displays in the instrument panelModification of the cruise
control speed only
Buttons 2 (SET+) and 3 (SET-)
If the cruise control is on, you can modify the
speed:
F
by s
uccessive short presses, to modify by
steps of + or -
1 m

ph (km/h),
F
by a m

aintained press, to modify in steps
of + or - 5 mph (km/h).
As a precaution, it is recommended that you
select a cruise speed setting close to the
current speed of your vehicle.
Driving

183
308_en_Chap06_conduite_ed02-2015
Modification of the cruise control speed and/or
the inter-vehicle time
Press button 5, the six memorised speeds and
the inter-vehicle time setting are displayed in
the touch screen.
F
Ch

oose a speed setting: it is displayed in
the instrument panel,
F
pr

ess or the " +" or " -" button to choose
a new inter-vehicle time setting between
2.5
se

conds and 1 second.
thi

s setting remains memorised, whatever the
state of the system.
the s

election screen closes after a few
moments.
the m

odifications are then accepted. In the event of the presence of a
vehicle detected by the radar, if the
speed selected is much higher than
the speed of that vehicle, the system
is not activated and the alert message
"Activation not possible, conditions
unsuitable" is displayed until driving
conditions are safe to allow activation of
the system.
Exceeding the programmed
speed
It is possible to exceed the programmed speed
temporarily by depressing the accelerator
pedal.
Simply release the accelerator pedal to return
to the programmed speed.
If the programmed setting is unintentionally
exceeded, descending a steep hill for example,
the speed setting in the instrument panel
flashes as a warning.
Button 5 (MEM)
6
Driving

184
308_en_Chap06_conduite_ed02-2015
the following table describes the alerts and the messages displayed for the different driving situations.the display of these alerts is not sequential.
Driving situations and associated alerts
Symbol Display in the
instrument panel Associated message
Comments
No vehicle detected:
the system operates as a standard cruise control.
Detection of a vehicle, at the limit of the range of the radar:
the system operates as a standard cruise control.
"SP
eeD A

DJ
uSteD"D

etection of a vehicle that is too close or running at a speed lower than your
vehicle's cruise speed setting.
the s

ystem uses engine braking to slow your vehicle (within a limit of 20 mph
(30 km/h)) and then hold it at the speed of the vehicle in front so as to observe the
programmed inter-vehicle time.
When automatically slowing down behind a vehicle, your true speed may be higher
than the "adjusted speed" displayed.
"SP
eeD A

DJ
uSteD"W

hen the adjusted speed reaches the limit of regulation (speed setting less than
20 mph (30 km/h)), the adjusted speed flashes together with the speed setting to
signal that automatic deactivation of the system is imminent.
"Cruise control
paused". If the system exceeds the limit of speed adjustment possible by the system and in
the absence of any reaction by the driver (operation of the direction indicator, change
of lane, reduction of the speed of the vehicle), the system is automatically paused.
the d

isplay of the deactivation message is accompanied by an audible signal.
Driving

187
308_en_Chap06_conduite_ed02-2015
Display of inter-vehicle time
using a radar located at the front of the vehicle,
t his system helps the driver maintain a safe
distance between their vehicle and the one in
front, by displaying the current inter-vehicle
time in the instrument panel.
It is the time interval, expressed in seconds,
that separates two vehicles in line.
the
r

ecommended safe value is about 2 seconds:
refer to the legislation or highway code in force
in your country.Activation / deactivation*
F Press this button, the indicator
l amp comes on.
the m

easurement is displayed for
information only: the system takes no
action on the vehicle.
thi

s system does not in any
circumstances replace the need for
vigilance on the part of the driver who
must remain in control of the vehicle at
all times.
the s

ystem is not designed for urban
use nor for more dynamic driving
(bends, acceleration, harsh braking…)
but rather when driving at a steady
speed.
the s

ystem is active in a speed range
between 42 and 93 mph (70 and
150
k

m/h).
Stationary vehicles and certain other
road users (such as bicycles for
example) are not detected.
the s

ystem displays inter-vehicle
time values of between 3 seconds and
0.5 of a second.
Below 0.5 of a second, the value
displayed is maintained at this level,
even if the true inter-vehicle time is less.
the s

tate of the system is memorised when the
ignition is switched off. Activation of the system is done in the " Driving
assistance " menu, with the engine running.
* Depending on version.
Conditions for display
the active cruise control must not be selected
( the active cruise control information is
displayed instead of that for the inter-vehicle
t i m e).
6
Driving

188
308_en_Chap06_conduite_ed02-2015
Once the speed conditions are met, a symbol is displayed in the instrument panel.
Displays
SymbolAssociated message Comments
No vehicle detected by the radar.
A vehicle is detected but the inter-vehicle time is more than 3 seconds. No value is
displayed.
A vehicle is detected.
the i

nter-vehicle time is 3 seconds or less.
the m
inimum value
displayed is 0.5 seconds, even if the true inter-vehicle time is lower.
"SYS
teM IN

AC
tIVe: Sp
eed
unsuitable" If the speed of your vehicle is outside the operating range.
Where the speed is not suitable, a message is displayed while the speed is outside limits
(below 42 mph (70 km/h) or above 93 mph (150 km/h), approximately). However, when
decelerating, the system is deactivated below 27 mph (45 km/h).
"SYS
teM IN

AC
tIVe: Vi
sibility
reduced"
the s

ystem switches to standby automatically if the sensor does not detect the vehicle in
front correctly (very difficult weather conditions, sensor out of adjustment, ...).
Driving