2016 Peugeot 308 reverse

260
308_en_Chap08_en-cas-de-panne_ed02-2015
Integrated direction indicator
side repeaters
You should contact a Peu geOt d ealer or a
qualified workshop for the replacement of these
bulbs. You should contact a P
eu
ge
Ot d
ealer or a
qualified workshop for the replacement of the
light emitting diode - L
eD.
Front foglamps
F unclip the finisher by pulling at the top
( cut-out).
F
Re

move the two screws to remove the unit
from its housing. F Di
sconnect the connector.
F uns crew the bulb holder (1/4 turn).
F
Re

move the bulb holder.
F
Ch

ange the failed bulb.
For reassembly, carry out these operations in
reverse order, pressing on the finisher to refit it.
Door mirror spotlamps
In the event of a breakdown

261
308_en_Chap08_en-cas-de-panne_ed02-2015
1. Sidelamps (light emitting diodes - LeDs ).
2. Re versing lamps (W16W).
3.
Di

rection indicators (PY21W amber).
4.
Br

ake lamps (light emitting diodes - L
eDs
).
5.
Fo

glamps (P21W).
Rear lamps
(hatchback)
Light emitting
diodes-LEDs
For replacement, contact a Peu geOt
d ealer or qualified workshop.
Reversing lamps, direction
indicators (on the wings)
F Disconnect the lamp connector.
F Re move the lamp fixing nut.
F
Ca

refully remove the lamp unit from
outside.
F


u
ns
crew the bulb holder (a quarter of a
turn) and change the bulb.
For reassembly, carry out these operations in
reverse order.
F Op
en the tailgate then remove the access
c ove r.
8
In the event of a breakdown

262
308_en_Chap08_en-cas-de-panne_ed02-2015
F unclip the left and right access covers.
F Re move the screws located in each
opening.
F


u
nc
lip the boot trim for access to the lamp
connector.
F
Di

sconnect the lamp connector.
F
Re

move the lamp fixing nut.
F
Ca

refully remove the lamp from the
outside.
F


u
ns
crew the bulb holder (a quarter of a
turn) and change the bulb.
For reassembly, carry out these operations in
reverse order.
Foglamp (tailgate)
F Open the tailgate and then remove the
l arge plastic cover.
In the event of a breakdown

263
308_en_Chap08_en-cas-de-panne_ed02-2015
Rear lamps
(SW)
Light emitting
diodes-LEDs
For replacement, contact a Peu geOt
d ealer or qualified workshop.
Direction indicators
(on the wings)
F Open the tailgate then remove the access
c ove r.
F
Re

move the two lamp fixing nut (pipe
spanner or socket recommended).
F
Disenga

ge the retaining clip, carefully
removing the lamp unit from outside. F
Di

sconnect the lamp connector.
F
Rem
ove the sealing foam.
F

u
nc
lip the bulb holder by pressing on the
two tongues.
F
Re
place the bulb.
For reassembly, carry out these operations in
reverse order.
1.
Si

delamps (light emitting diodes - L
eDs

).
2.
Di

rection indicators (PY21W amber).
3.
Br

ake lamps (light emitting diodes - L
eDs

).
4.
Re

versing lamps (W16W).
5.
Fo

glamps (P21W).
8
In the event of a breakdown

264
308_en_Chap08_en-cas-de-panne_ed02-2015
Reversing lamp, rear foglamp
(tailgate)
F Open the tailgate and then remove the
a
ccess cover. F
Ca

refully remove the lamp from the
outside.
F
Di
sconnect the lamp connector.
F
Fo
glamp: unclip the bulb holder by
pressing on the two tongues then replace
the bulb.
F
Re
versing lamp: turn the bulb holder a
quarter of a turn then replace the bulb.
For reassembly, carry out these operations in
reverse order.
F
Re

move the lamp fixing nut.
In the event of a breakdown

273
308_en_Chap08_en-cas-de-panne_ed02-2015
Starting using another battery
First check that the slave battery has a
nominal voltage of 12 V and a capacity
at least equal to that of the discharged
battery.
Do not try to start the engine by
connecting a battery charger.
Do not disconnect the (+) terminal when
the engine is running.
F
Re

move the plastic cover from
the
(

+)
t
erminal, if your vehicle has one.
F
Co

nnect the red cable to the positive
terminal (+) of the flat battery A , then to the
positive terminal (+) of the slave battery B.
F
Co

nnect one end of the green or black
cable to the negative terminal (-) of the
slave battery B (or earth point on the other
vehicle).
F
Co

nnect the other end of the green or black
cable to the earth point C on the broken
down vehicle (or on the engine mounting).
F
St

art the engine of the vehicle with the
good battery and leave it running for a
few
m

inutes. F
Op

erate the starter on the broken down
vehicle and let the engine run
If t

he engine does not start straight
away, switch off the ignition and wait a
few
m

oments before trying again.
F
Wa

it until the engine returns to idle then
disconnect the jump lead cables in the
reverse order.
F
Re

fit the plastic cover to the (+) terminal, if
your vehicle has one.
When your vehicle's battery is discharged, the
engine can be started using a slave battery
(external or on another vehicle) and jump lead
cables.Before disconnecting the battery
Wait 2 minutes after switching off the ignition
before disconnecting the battery.
Close the windows and the doors before
disconnecting the battery.
Following reconnection of the
battery
Following reconnection of the battery, switch on
the ignition and wait 1 minute before starting to
permit initialisation of the electronic systems.
However, if problems remain following this
operation, contact a P
eu

ge
Ot d
ealer or a
qualified workshop.
Referring to the corresponding section, you
must yourself reinitialise (depending on
version):
-
th

e remote control key,
-
th

e electric blind(s),
-
... S

ome functions are not available if the
battery is not sufficiently charged.
8
In the event of a breakdown

274
308_en_Chap08_en-cas-de-panne_ed02-2015
the batteries contain harmful substances
s uch as sulphuric acid and lead. the y
must be disposed of in accordance
with regulations and must not, in any
circumstances, be discarded with household
waste.
tak

e used remote control batteries and
vehicle batteries to a special collection point.
It is advisable to disconnect the battery
if the vehicle is to be left unused for
more than one month. Protect your eyes and face before
handling the battery.
All operations on the battery must be
carried out in a well ventilated area and
away from naked flames and sources
of sparks, so as to avoid the risk of
explosion or fire.
Do not try to charge a frozen battery;
the battery must first be thawed out to
avoid the risk of explosion. If the battery
has been frozen, before charging have
it checked by a Peu
geOt d ealer or a
qualified workshop who will check that
the internal components have not been
damaged and the casing is not cracked,
which could cause a leak of toxic and
corrosive acid.
Do not reverse the polarity and use only
a 12 V charger.
Do not disconnect the terminals while
the engine is running.
Do not charge the batteries without
disconnecting the terminals first.
Wash your hands afterwards.
With Stop & Start, the battery does not
have to be disconnected for charging.
F
Di

sconnect the battery from the vehicle.
F
Fo

llow the instructions for use provided by
the manufacturer of the charger.
F Co
nnect the battery starting with the
negative terminal (-).
F
Ch

eck that the terminals and connectors
are clean. If they are covered with sulphate
(whitish or greenish deposit), remove them
and clean them.
Charging the battery using
a battery charger
Do not push the vehicle to start the
engine if your vehicle has an automatic
gearbox.
In the event of a breakdown