Page 3482 of 3641
G SENSORTM-241
< REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
G SENSOR
Exploded ViewINFOID:0000000012431189
Removal and InstallationINFOID:0000000012431190
CAUTION:
• Do not drop or strike G sensor, because it may be damaged by impact.
• Do not use a power tool.
REMOVAL
1. Disconnect the battery negative terminal. Refer to PG-70, "Exploded View".
2. Remove center console assembly. Refer to IP-18, "
Removal and Installation".
3. Disconnect the harness connector from G sensor.
4. Remove G sensor.
INSTALLATION
Installation is in the reverse order of removal.
AdjustmentINFOID:0000000012431191
ADJUSTMENT AFTER INSTALLATION
Perform “G SENSOR CALIBRATION”. Refer to TM-130, "Description".
1. G sensor Front
JSDIA1922GB
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3485 of 3641
![NISSAN NOTE 2016 Service Repair Manual TM-244
< REMOVAL AND INSTALLATION >[CVT: RE0F11A]
OIL PAN, CONTROL VALVE
• To remove bolt of the oil temperature sensor bracket and
the control valve, fix bracket with flat-blade screw-
driver.
11 NISSAN NOTE 2016 Service Repair Manual TM-244
< REMOVAL AND INSTALLATION >[CVT: RE0F11A]
OIL PAN, CONTROL VALVE
• To remove bolt of the oil temperature sensor bracket and
the control valve, fix bracket with flat-blade screw-
driver.
11](/manual-img/5/57363/w960_57363-3484.png)
TM-244
< REMOVAL AND INSTALLATION >[CVT: RE0F11A]
OIL PAN, CONTROL VALVE
• To remove bolt of the oil temperature sensor bracket and
the control valve, fix bracket with flat-blade screw-
driver.
11. Remove the O-ring to the CVT unit harness connector.
INSTALLATION
1. Install the O-ring to the CVT unit harness connector. CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to the O-ring
• Never pinch the harness , between the control valve and
the CVT unit harness connector bracket .
• Never twist the harness.
• Never slack the harness.
2. Install the control valve, and than tighten control valve bolts to the specitoed torque.
CAUTION:
• Never pinch the harness be tween the control valve and
the transaxle case.
• Never drop the control valve and manual valve.
3. Install the manual plate and washer , and then tighten nut to the specitied torque.
CAUTION:
To tighten nut, fix manual plat e with flat-blade screwdriver.
JSDIA6596ZZ
JSDIA6599ZZ
JSDIA6598ZZ
JSDIA6597ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3487 of 3641
TM-246
< REMOVAL AND INSTALLATION >[CVT: RE0F11A]
PRIMARY SPEED SENSOR
PRIMARY SPEED SENSOR
Exploded ViewINFOID:0000000012431195
Removal and InstallationINFOID:0000000012431196
REMOVAL
1. Partially remove fender protector (LH). Refer to
TM-246, "Exploded View".
2. Disconnect the harness connector from primary speed sensor.
3. Remove the primary speed sensor.
4. Remove the O-ring from the primary speed sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply Genuine NISSAN CVT Fluid NS-3 to the O-ring.
Inspection and AdjustmentINFOID:0000000012431197
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to TM-228, "Inspection".
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to TM-229, "Adjustment".
1. Transaxle assembly 2. O-ring 3. Primary speed sensor
Front : Genuine NISSAN CVT Fluid NS-3
JSDIA1880GB
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3488 of 3641
![NISSAN NOTE 2016 Service Repair Manual SECONDARY SPEED SENSORTM-247
< REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SECONDARY SPEED SENSOR
Exploded ViewINFOID:0000000012431198
Removal and InstallationINFOID:0000 NISSAN NOTE 2016 Service Repair Manual SECONDARY SPEED SENSORTM-247
< REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SECONDARY SPEED SENSOR
Exploded ViewINFOID:0000000012431198
Removal and InstallationINFOID:0000](/manual-img/5/57363/w960_57363-3487.png)
SECONDARY SPEED SENSORTM-247
< REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SECONDARY SPEED SENSOR
Exploded ViewINFOID:0000000012431198
Removal and InstallationINFOID:0000000012431199
REMOVAL
1. Remove battery tray. Refer to PG-71, "Removal and Installation (Battery Tray)".
2. Remove IPDM/ER. Refer to PCS-30, "
Removal and Installation".
3. Disconnect the harness connector from secondary speed sensor.
4. Remove the secondary speed sensor.
5. Remove the O-ring from the secondary speed sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply Genuine NISSAN CVT Fluid NS-3 to the O-ring.
Inspection and AdjustmentINFOID:0000000012431200
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to TM-228, "Inspection".
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to TM-229, "Adjustment".
1. Transaxle assembly 2. O-ring3. Secondary speed sensor
Front : Genuine NISSAN CVT Fluid NS-3
JSDIA1881GB
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3489 of 3641
TM-248
< REMOVAL AND INSTALLATION >[CVT: RE0F11A]
OUTPUT SPEED SENSOR
OUTPUT SPEED SENSOR
Exploded ViewINFOID:0000000012431201
Removal and InstallationINFOID:0000000012431202
REMOVAL
1. Disconnect the harness connector from output speed sensor.
NOTE:
Lift up the vehicle and perform the work from rear of the transaxle assembly.
2. Remove the output speed sensor.
3. Remove the O-ring from the output speed sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply Genuine NISSAN CVT Fluid NS-3 to the O-ring.
Inspection and AdjustmentINFOID:0000000012431203
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to TM-228, "Inspection".
ADJUSTMENT AFTER INSTALLATION
Check the CVT fluid level. Refer to TM-229, "Adjustment".
1. Transaxle assembly 2. Output speed sensor 3. O-ring
Front Genuine NISSAN CVT Fluid NS-3
JSDIA1882GB
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3501 of 3641
![NISSAN NOTE 2016 Service Repair Manual TM-260
< UNIT REMOVAL AND INSTALLATION >[CVT: RE0F11A]
TRANSMISSION ASSEMBLY
• Primary speed sensor harness connector
• Secondary speed sensor harness connector
• Output speed sensor harness con NISSAN NOTE 2016 Service Repair Manual TM-260
< UNIT REMOVAL AND INSTALLATION >[CVT: RE0F11A]
TRANSMISSION ASSEMBLY
• Primary speed sensor harness connector
• Secondary speed sensor harness connector
• Output speed sensor harness con](/manual-img/5/57363/w960_57363-3500.png)
TM-260
< UNIT REMOVAL AND INSTALLATION >[CVT: RE0F11A]
TRANSMISSION ASSEMBLY
• Primary speed sensor harness connector
• Secondary speed sensor harness connector
• Output speed sensor harness connector
• Ground
3. Rotate the crankshaft and remove the nuts that secure the drive plate to the torque converter from the sta- tor motor mount.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from the front of the engine.
4. Remove the bolts (engine to transaxle) that fasten the transaxle assembly and engine assembly.
5. Remove transaxle assembly from engine. CAUTION:
• Secure torque converter to prevent it from dropping.
• Secure transaxle assembly to a suitable jack.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-rings.
• Apply Genuine NISSAN CVT Fluid NS-3 to the O-rings.
• When installing the transaxle assembly onto the engine assembly,
check the engagement of the dowel pins ( ).
• When using suitable tool (A) for alignment, install it to the align- ment stud bolt used to align the torque converter to the drive plate.
JSDIA1839ZZ
Bolt position ABC D
Direction of insertion Transaxle assembly
⇒
Engine assembly Engine assembly
⇒ Transaxle assembly
Q ua ntit y 2213
JSDIA1184ZZ
JPDIA0683ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3508 of 3641

VTL-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012430544
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for WorkINFOID:0000000012430545
• When removing or disassembling each component, be careful not to damage or deform it. If a component may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3519 of 3641

WCS-4
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012542981
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Revision: August 2015 2016 Versa Note
cardiagn.com