2016 NISSAN NOTE brake fluid

C1142 PRESS SENSORBRC-97
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Check the brake fluid leakage. Refer to BR-12, "Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace brake fluid leakage part.
3.CHECK BRAKE PIPING
Check the brake piping. Refer to BR-12, "
Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace brake piping. • Front: Refer to BR-23, "
FRONT : Removal and Installation".
• Rear: Refer to BR-26, "
REAR : Removal and Installation".
4.CHECK BRAKE PEDAL
Check the brake pedal.
• Brake pedal height: Refer to BR-9, "
Inspection and Adjustment".
• Brake pedal assembly: Refer to BR-20, "
Exploded View".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Adjust the brake pedal height or replace brake pedal assembly. • Adjust the brake pedal: Refer to BR-9, "
Inspection and Adjustment".
• Replace the brake pedal: Refer to BR-20, "
Removal and Installation".
5.CHECK BRAKE MASTER CYLINDER
Check the brake master cylinder. Refer to BR-14, "
Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace brake master cylinder. Refer to BR-28, "
Removal and Installation".
6.CHECK BRAKE BOOSTER
Check the brake booster. Refer to BR-15, "
Inspection".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace brake booster. Refer to BR-31, "
Removal and installation".
7.CHECK VACUUM PIPING
Check the vacuum piping. Refer to BR-33, "
Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO >> Repair or replace vacuum piping. Refer to BR-33, "
Removal and Installation".
8.CHECK FRONT DISC BRAKE
Check the front disc brake caliper. Refer to BR-36, "
BRAKE CALIPER ASSEMBLY : Exploded View".
Is the inspection result normal?
YES >> GO TO 9.
NO >> Repair or replace front disc brake caliper. Refer to BR-37, "
BRAKE CALIPER ASSEMBLY :
Removal and Installation".
9.CHECK REAR BRAKE
Check the rear brake. Refer to BR-41, "
Exploded View".
Is the inspection result normal?
YES >> GO TO 10.
NO >> Repair or replace rear brake. Refer to BR-41, "
Removal and Installation".
10.CHECK ABS ACTUATOR AND ELECTRIC UNIT (C ONTROL UNIT) POWER SUPPLY AND GROUND
CIRCUIT
Revision: August 2015 2016 Versa Note

cardiagn.com

BRC-108
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1155 BRAKE FLUID LEVEL SWITCH
C1155 BRAKE FLUID LEVEL SWITCH
DTC DescriptionINFOID:0000000012430887
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the
ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1155” detected?
YES-1 >> “C1155” is displayed as “CRNT”: Proceed to BRC-108, "Diagnosis Procedure".
YES-2 >> “C1155” is displayed as “PAST”: Inspection End (Erase “Self Diagnostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430888
1.CHECK BRAKE FLUID LEVEL
1. Turn the ignition switch OFF.
2. Check the brake fluid level. Refer to BR-12, "
Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Refill brake fluid. Refer to BR-12, "
Refilling". GO TO 2.
2.PERFORM SELF-DIAGNOSIS (1)
With CONSULT
1. Erase “Self Diagnostic Result” of “ABS”
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C1155 BR FLUID LEVEL LOW
(Brake fluid level low) • When brake fluid level low signal is detected.
• When an open circuit is detected in brake fluid level switch circuit.
PAST DTC
CRNT DTC
• Harness or connector
• Brake fluid level is low • Harness or connector
• ABS actuator and electric unit (control unit)
• Brake fluid level switch
• Combination meter
• Brake fluid level is low
Revision: August 2015
2016 Versa Note

cardiagn.com

C1155 BRAKE FLUID LEVEL SWITCHBRC-109
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
4. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1155” detected?
YES >> GO TO 3.
NO >> Inspection End.
3.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Check the combination meter harness connector for disconnection or looseness.
3. Check the brake fluid level switch harness connector for disconnection or looseness.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair / replace harness or connector, and GO TO 4.
4.PERFORM SELF-DIAGNOSIS (2)
With CONSULT
1. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1155” detected?
YES >> GO TO 5.
NO >> Inspection End.
5.CHECK BRAKE FLUID LEVEL SWITCH
Check the brake fluid level switch. Refer to BR-28, "
Exploded View".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Replace the reservoir tank. Refer to BR-28, "
Exploded View". GO TO 6.
6.PERFORM SELF-DIAGNOSIS (3)
With CONSULT
1. Erase “Self Diagnostic Result” of “ABS”
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
NOTE:
Wait at least 10 seconds after starting the engine.
4. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1155” detected?
YES >> GO TO 7.
NO >> Inspection End.
7.CHECK CONNECTOR AND TERMINAL
1. Turn the ignition switch OFF.
2. Disconnect brake fluid level switch harness connector.
3. Check the brake fluid level switch harness connector for disconnection or looseness.
4. Check the brake fluid level switch pin terminal s for damage or loose connection with harness connector.
5. Disconnect combination meter harness connector.
Revision: August 2015 2016 Versa Note

cardiagn.com

BRC-110
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1155 BRAKE FLUID LEVEL SWITCH
6. Check the combination meter harness connector for disconnection or looseness.
7. Check the combination meter pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >> GO TO 9.
NO >> Repair / replace harness, connector, or terminal, and GO TO 8.
8.PERFORM SELF-DIAGNOSIS (4)
With CONSULT
1. Erase “Self Diagnostic Result” of “ABS”
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
4. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1155” detected?
YES >> GO TO 9.
NO >> Inspection End.
9.CHECK BRAKE FLUID LEVEL SWITCH CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect brake fluid level switch harness connector.
3. Disconnect combination meter harness connector.
4. Check the continuity between brake fluid level switch harness connector and combination meter harness
connector.
5. Check the continuity between brake fluid level switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 10.
NO >> Repair / replace harness or connector, and GO TO 10.
10.CHECK BRAKE FLUID LEVEL SWITCH GROUND CIRCUIT
Check the continuity between brake fluid level switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 11.
NO >> Repair / replace harness or connector, and GO TO 11.
11 .CHECK COMBINATION METER
Check the combination meter. Refer to MWI-18, "
CONSULT Function (METER/M&A)" (TYPE A) or MWI-71,
"CONSULT Function (METER/M&A)" (TYPE B).
Is the inspection result normal?
Brake fluid level switch Combination meter
Continuity
Connector TerminalConnector Terminal
E40 1M24 (TYPE B)
11Ye s
M82 (TYPE A)
Brake fluid level switch —Continuity
Connector Terminal
E40 1Ground No
Brake fluid level switch
—Continuity
Connector Terminal
E40 2Ground Yes
Revision: August 2015 2016 Versa Note

cardiagn.com

C1155 BRAKE FLUID LEVEL SWITCHBRC-111
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-144, "Removal and Instal-
lation".
NO >> Repair or replace combination meter. Refer to MWI-54, "
Removal and Installation" (TYPE A) or
MWI-115, "
Removal and Installation" (TYPE B).
Component InspectionINFOID:0000000012430889
1.CHECK BRAKE FLUID LEVEL SWITCH
1. Turn the ignition switch OFF.
2. Disconnect brake fluid level switch harness connector.
3. Check the continuity between terminals of brake fluid level switch.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace the reservoir tank. Refer to BR-28, "
Exploded View".
Brake fluid level switch
Condition Continuity
Te r m i n a l
1 – 2 When brake fluid level in reservoir tank is within the specified level. No
When brake fluid level in reservoir tank is less than the specified level. Yes
Revision: August 2015
2016 Versa Note

cardiagn.com

BRC-134
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
UNEXPECTED PEDAL REACTION
UNEXPECTED PEDAL REACTION
Diagnosis ProcedureINFOID:0000000012430919
1.CHECK BRAKE PEDAL STROKE
Check brake pedal stroke. Refer to BR-9, "
Inspection and Adjustment".
Is the stroke too big?
YES >> • Bleed air from brake line and hose. Refer to BR-13, "Bleeding Brake System".
• Check brake pedal, brake booster, and master cylinder for mount play, looseness, brake system fluid leakage, etc. Refer to brake pedal: BR-9, "
Inspection and Adjustment" or brake booster
assembly BR-15, "
Inspection".
NO >> GO TO 2.
2.CHECK ABS FUNCTION
1. Disconnect ABS actuator and electric unit (control unit) connector to deactivate ABS.
2. Check if braking force is normal in this condition.
3. Reconnect connector after inspection.
Is the inspection result normal?
YES >> Inspection End.
NO >> Check brake system.
Revision: August 2015 2016 Versa Note

cardiagn.com

BRC-144
< REMOVAL AND INSTALLATION >[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
ABS ACTUATOR AND ELECTRIC
UNIT (CONTROL UNIT)
Exploded ViewINFOID:0000000012430931
Removal and InstallationINFOID:0000000012430932
REMOVAL
CAUTION:
• Before servicing, disconnect the ba ttery cable from negative terminal.
• Do not remove actuator by holding harness.
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
1. Disconnect negative battery cable. Refer to PG-70, "
Removal and Installation (Battery)".
2. Disconnect vacuum hose from intake manifold. Refer to BR-33, "
Exploded View".
1. ABS actuator and electric unit (con-
trol unit) 2. ABS actuator and electric unit (con-
trol unit) harness connector 3. Bracket
4. Bushing 5. Insulating clip6. Bolt
A. To master cylinder secondary side B. To rear brake tube (RH) C. To front brake tube (LH)
D. To front brake tube (RH) E. To rear brake tube (LH)F. To master cylinder primary side
AWFIA1105ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

EM-28
< REMOVAL AND INSTALLATION >[HR16DE]
INTAKE MANIFOLD
INTAKE MANIFOLD
Exploded ViewINFOID:0000000012431705
Removal and InstallationINFOID:0000000012431706
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc.
, cap or plug openings to prevent fluid from spill-
ing.
1. Remove air duct (inlet), air duct and air cleaner. Refer to EM-26, "
Removal and Installation".
2. Disconnect water hoses from the electr ic throttle actuator (if necessary).
CAUTION:
• Perform this step when the engine is cold.
• Do not spill engine coolant on the drive belt.
3. Remove electric throttle control actuator. CAUTION:
• Handle carefully to avoid any shock to electric throttle control actuator.
• Do not disassemble electric throttle control actuator.
4. Disconnect EVAP purge control solenoid valve har ness connector and vacuum hose from EVAP purge
control solenoid valve.
CAUTION:
1. EVAP canister purge volume control
solenoid valve 2. Hose clamp
3. Vacuum hose
4. PCV hose 5. Hose clamp6. Intake manifold gasket
7. Intake manifold 8. Electric throttle control actuator 9. Electric throttle control actuator
gasket
10. EVAP service port A. To air ductB. To centralized under-floor piping
C. To air duct D. To brake boosterE. To PCV valve in rocker cover
Front
AWBIA1602ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com