2016 NISSAN NOTE key

SQUEAK AND RATTLE TROUBLE DIAGNOSESDLK-139
< SYMPTOM DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
LAIA0071E
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-140
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
HOOD
REMOVAL AND INSTALLATION
HOOD
Exploded ViewINFOID:0000000012430085
HOOD ASSEMBLY
HOOD ASSEMBLY : Removal and InstallationINFOID:0000000012430086
CAUTION:
• Use two people when removing or installing hood assembly due to its heavy weight.
• Use protective tape or shop cloths to protect surrounding components from damage during removal
and installation of hood assembly.
REMOVAL
1. Support hood assembly using a suitable tool.
WARNING:
Bodily injury may occur if hood assembly is not supported properly when removing hood assem-
bly.
2. Remove hood hinge nuts and hood assembly.
3. Remove clips and hood insulator (if necessary).
INSTALLATION
1. Hood 2. Bumper rubber (hood side) 3. Hood insulator
4. Hood rod clamp 5. Bumper rubber (body side) 6. Hood rod grommet
7. Hood hinge (LH) 8. Hood support rod 9. Hood hinge (RH)
A. Hood insulator clip
AWKIA2564ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

HOOD
DLK-141
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
Installation is in the reverse order of removal.
CAUTION:
• Before installing hood assembl y, apply anticorrosive agent to the surface of hood hinge.
• After installation, perform the hood assembly adjustment procedure. Refer to DLK-141, "
HOOD
ASSEMBLY : Adjustment".
• After installation, ap ply touch-up paint (body color) to the head of hood hinge nuts.
HOOD ASSEMBLY : AdjustmentINFOID:0000000012430087
Check the clearance and the surface height between hood and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specific ation, adjust them according to the adjustment proce-
dure.
Unit: mm (in)
1. Hood assembly 2. Bumper rubber (body side) 3. Hood hinge (LH)
4. Hood lock 5. Front grille finisher6. Front combination lamp
7. Front fender
AWKIA2565ZZ
Section Item Measurement StandardParallelism Equality
A – A D
Clearance 4.4 ± 2.0 (0.17 ± 0.08) 2.0 (0.08) —
E Surface height -0.5 +2.0, -1.5 (0.02 +0.08, -0.06) 2.0 (0.08) —
B – B F
Clearance 4.0 ± 2.0 (0.16 ± 0.08) 2.0 (0.08) 3.0 (0.12)
G Surface height ———
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-142
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
HOOD
CLEARANCE ADJUSTMENT
1. Loosen hood hinge nuts and bolts.
2. Loosen hood lock assembly bolts.
3. Adjust the hood lock assembly so the clearance m
easurements are within the specifications provided.
4. Tighten hood hinge nuts and bolts to specified torque.
5. Tighten hood lock assembly bolts to specified torque.
HEIGHT ADJUSTMENT
1. Loosen hood lock assembly bolts.
2. Adjust the surface height of hood assembly to front upper grille, front fender and front combination lamp to
the specified values by rotating hood bumper rubber.
3. Temporarily tighten hood lock assembly bolts.
4. Adjust (A) as shown to the following value with hood’s own weight by dropping it from approximately 200 mm (7.87 in) height or by pressing hood lightly [approximately 29 N (3.0 kg, 6.5 lb)].
5. After adjustment, tighten hood lock assembly bolts to specified torque.
HOOD HINGE
HOOD HINGE : Removal and InstallationINFOID:0000000012430088
REMOVAL
1. Remove hood assembly. Refer to DLK-140, "HOOD ASSEMBLY : Removal and Installation".
2. Remove front fender. Refer to DLK-147, "
Removal and Installation".
3. Remove cowl top side cover. Refer to EXT-36, "
Exploded View".
4. Remove hood hinge bolts and hood hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Before installing the hood hinge, apply anticorrosive agent onto the surface of the vehicle.
C – CH Clearance 3.5
± 1.0 (0.14 ± 0.04) 1.5 (0.06) 1.5 (0.06)
J Surface height 0.0 ± 1.5 (0.0 ± 0.06) 1.5 (0.06) 1.5 (0.06)
Section Item Measurement
StandardParallelism Equality
1. Hood striker 2. Secondary latch3. Primary latch
A. 20.0 mm (0.79 in)
ALKIA3162ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

HOOD
DLK-143
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
• Check hood hinge rotating point for poor lubrication. If neces-
sary, apply a suitable multi-purpose grease.
HOOD SUPPORT ROD
HOOD SUPPORT ROD : Removal and InstallationINFOID:0000000012430089
REMOVAL
1. Support hood assembly using a suitable tool.
WARNING:
Bodily injury may occur if hood assembly is not supported properly when removing hood support
rod.
2. Rotate and remove hood support rod from grommet.
3. Release tab and remove grommet from hood hinge (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
JMKIA7995ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-144
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
Exploded ViewINFOID:0000000012430090
RADIATOR CORE SUPPORT UPPER
RADIATOR CORE SUPPORT UPPER
: Removal and InstallationINFOID:0000000012430091
REMOVAL
1. Remove front grille. Refer to EXT-32, "Removal and Installation".
2. Remove ground harness bolt (A).
1. Upper air guide 2. Air guide (RH)3. Front bumper reinforcement
4. Lower air guide 5. Air guide (LH)6. Radiator core lower support
7. Lower grommet 8. Upper grommet9. Radiator core upper support
Clip
ALKIA3172ZZ
ALKIA3174ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

RADIATOR CORE SUPPORTDLK-145
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
3. Remove washer tube inlet clip (A).
4. Remove radiator cap adapter bracket bolt (A) and radiator reser- voir tank bolt (B).
5. Remove horn. Refer to HRN-6, "
Removal and Installation".
6. Remove crash zone sensor. Refer to SR-24, "
Removal and Installation".
7. Remove hood lock assembly. Refer to DLK-165, "
HOOD LOCK : Removal and Installation".
8. Release hood lock release cable clips from radi ator core support upper using a suitable tool.
9. Remove upper air guide. Refer to DLK-144, "
Exploded View".
10. Remove air guide (LH/RH). Refer to DLK-144, "
Exploded View".
11. Release all harness connector clips from radiator core support upper using a suitable tool.
12. Remove bolts (A) and radiator core support upper.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, perform hood assembl y adjustment procedure. Refer to DLK-141, "
HOOD ASSEM-
BLY : Adjustment".
RADIATOR CORE SUPPORT LOWER
RADIATOR CORE SUPPORT LOWE R : Removal and InstallationINFOID:0000000012430092
REMOVAL
1. Remove radiator core support upper. Refer to DLK-144, "RADIATOR CORE SUPPORT UPPER :
Removal and Installation".
2. Reposition the radiator and condenser.
AWKIA2567ZZ
JMKIA8027ZZ
AWKIA2568ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-146
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
3. Using a suitable tool (A), suspend radiator and condenser to
prevent them from falling.
CAUTION:
Use care to avoid damaging radiator and condenser.
4. Remove bolts (A) and radiator core support lower (1).
INSTALLATION
Installation is in the reverse order of removal.
JMKIA8030ZZ
ALKIA3181ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com