REAR SEAT BELTSB-13
< REMOVAL AND INSTALLATION >
C
DE
F
G
I
J
K L
M A
B
SB
N
O P
2. Release seat belt retractor (center) (1) from seat belt buckle (LH) (2) using a suitable tool (A) as shown.
3. Remove seat belt buckle anchor bolt and seat belt buckle (LH). CAUTION:
Before removing the seat belt buckle anchor bolt , note the positions of washers and spacers for
correct installation.
INSTALLATION
Installation is in the reverse order of removal.
• Tighten the seat belt buckle anchor bolt to specification. Refer to SB-12, "
Exploded View".
• Always perform an inspection after repair to make sure the system is functioning within specifications. Refer
to SB-5, "
Inspection".
REMOVAL - Seat Belt Buckle (RH)
1. Remove rear seat cushion. Refer to SE-26, "SEAT CUSHION : Removal and Installation".
2. Remove seat belt buckle anchor bolt and seat belt buckle (RH). CAUTION:
Before removing the seat belt buckle anchor bolt , note the positions of washers and spacers for
correct installation.
INSTALLATION
Installation is in the reverse order of removal.
• Tighten the seat belt buckle anchor bolt to specification. Refer to SB-12, "
Exploded View".
• Always perform an inspection after repair to make sure the system is functioning within specifications. Refer
to SB-5, "
Inspection".
SEAT BELT RETRACTOR
SEAT BELT RETRACTOR : Removal and InstallationINFOID:0000000012430706
REMOVAL - Seat Belt Retractor (LH/RH)
1. Remove luggage side upper finisher (LH/RH). Refer to INT-35, "LUGGAGE SIDE UPPER FINISHER :
Removal and Installation".
ALHIA0315ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
SB-14
< REMOVAL AND INSTALLATION >
REAR SEAT BELT
2. For seat belt retractor (LH) (1).
a. Remove D-ring anchor bolt (A).: Front
CAUTION:
Before removing the D-ring anchor bolt, note the positions
of washers and spacers fo r correct installation.
b. Remove bolts (B) and the seat belt retractor (LH) (1). (2): Seat belt retractor (center)
3. For seat belt retractor (RH) (3). : Front
a. Remove D-ring anchor bolt (C). CAUTION:
Before removing the D-ring anchor bolt, note the positions
of washers and spacers fo r correct installation.
b. Remove bolts (D) and seat belt retractor (RH) (3).
INSTALLATION
Installation is in the reverse order of removal.
• Install the seat belt retractor upper bolt first.
• Tighten the D-ring anchor bolt and the seat belt re tractor bolts to specification. Refer to SB-12, "
Exploded
View".
• Make sure the D-ring anchor operates freely.
• Always perform an inspection after repair to make sure the system is functioning within specifications. Refer to SB-5, "
Inspection".
REMOVAL - Seat Belt Retractor (center)
1. Remove luggage side upper finisher (LH). Refer to INT-35, "LUGGAGE SIDE UPPER FINISHER :
Removal and Installation".
2. Remove D-ring anchor bolt (A). : Front
CAUTION:
Before removing the D-ring anchor bolt, note the positions
of washers and spacers fo r correct installation.
3. Remove bolts (B) and seat belt retractor (center) (1). (2): Seat belt retractor (LH)
INSTALLATION
Installation is in the reverse order of removal.
• Install the center seat belt retractor upper bolt first.
• Tighten the D-ring anchor bolt and the seat belt re tractor bolts to specification. Refer to SB-12, "
Exploded
View".
• Make sure the D-ring anchor operates freely.
• Always perform an inspection after repair to make sure the system is functioning within specifications. Refer
to SB-5, "
Inspection".
ALHIA0318ZZ
ALHIA0313ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
SE-1
BODY INTERIOR
C
DE
F
G H
I
K L
M
SECTION SE
A
B
SE
N
O P
CONTENTS
SEAT
PRECAUTION ....... ........................................2
PRECAUTIONS .............................................. .....2
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
2
Precaution for Work ..................................................2
PREPARATION ............................................3
PREPARATION .............................................. .....3
Special Service Tools .......................................... ......3
Commercial Service Tools ........................................3
CLIP LIST ............................................................4
Descriptions for Clips ................................................4
SYMPTOM DIAGNOSIS ...............................8
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES ........................ ........................................
8
Work Flow ........................................................... ......8
Generic Squeak and Rattle Troubleshooting ............9
Diagnostic Worksheet .............................................12
WIRING DIAGRAM ......................................14
HEATED SEAT SYSTEM ...................................14
Wiring Diagram ................................................... ....14
REMOVAL AND INSTALLATION ...............18
FRONT SEAT ................................................. ....18
DRIVER SIDE ........................................................ ....18
DRIVER SIDE : Exploded View ..............................18
DRIVER SIDE : Removal and Installation ...............20
PASSENGER SIDE ...................................................20
PASSENGER SIDE : Exploded View .................. ....21
PASSENGER SIDE : Removal and Installation ......22
REAR SEAT ......................................................23
Exploded View ..................................................... ....23
SEAT CUSHION .................................................... ....26
SEAT CUSHION : Removal and Installation ...........26
SEATBACK ............................................................ ....26
SEATBACK : Removal and Installation ...................26
SEATBACK HINGE ............................................... ....27
SEATBACK HINGE : Removal and Installation .......27
SEATBACK STRIKER ........................................... ....27
SEATBACK STRIKER : Removal and Installation ....27
SEAT CUSHION HOOK ......................................... ....27
SEAT CUSHION HOOK : Removal and Installa-
tion ...........................................................................
27
FRONT HEATED SEAT SWITCH .....................29
Removal and Installation .........................................29
UNIT DISASSEMBLY AND ASSEMBLY ....30
FRONT SEAT ....................................................30
DRIVER SIDE ......................................................... ....30
DRIVER SIDE : Exploded View ...............................30
DRIVER SIDE : Seatback ........................................32
DRIVER SIDE : Seat Cushion .................................33
PASSENGER SIDE ....................................................34
PASSENGER SIDE : Explode d View ......................35
PASSENGER SIDE : Seatback ...............................36
PASSENGER SIDE : Seat Cushion ........................36
REAR SEAT ......................................................38
Exploded View ..................................................... ....38
Seat Cushion ...........................................................41
Seatback ..................................................................42
Revision: August 2015 2016 Versa Note
cardiagn.com
SE-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012432026
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for WorkINFOID:0000000012432027
• When removing or disassembling each component, be careful not to damage or deform it. If a component may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Revision: August 2015 2016 Versa Note
cardiagn.com
FRONT SEATSE-19
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
DRIVER SEAT WITHOUT LIFT AND ARMREST
1. Armrest 2. Seat cushion outer finisher (RH) 3. Seat belt buckle
4. Seat cushion outer finisher (LH) 5. Lift lever 6. Lift lever cap
7. Recline lever 8. Headrest holder (locked) 9. Headrest holder (free)
10. Headrest 11. Seat assembly
AWJIA1998ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
SE-20
< REMOVAL AND INSTALLATION >
FRONT SEAT
DRIVER SIDE : Remova l and Installation
INFOID:0000000012432036
WARNING:
• Do not leave any objects (screwdriver s, tools, etc.) on the seat during repair. It can lead to personal
injury if the side air bag module should accidentally deploy.
• Always work from the side or back of th e seatback, do not work in front of seat.
• Do not use air tools or electric tools for servicing the seat.
• Do not drop, tilt, or bump the si de air bag module while installing the seat. Always handle it with
care.
• After the side air bag module inflates, the front seat frame must be replaced.
• Before removing the front seat, tu rn the ignition switch OFF, disconnect both battery cables then
wait at least three minutes.
CAUTION:
• When removing and installing the seat, use shop cloths to pr otect components from damage.
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to PG-70,
"Removal and Installation (Battery)".
2. Slide the seat to the full forward position.
3. Remove the seat rear bolts.
4. Slide the seat to the full rearward position.
5. Remove the seat front bolts.
6. Tilt the seat rearward and disconnect the harness connectors from the seat and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Make sure that the seat harness or the floor trim is not damaged during installation.
When installing the driver side front seat, tighten the bolts in the
order shown.
PASSENGER SIDE
1. Seat cushion outer finisher (RH) 2. Seat belt buckle 3. Seat cushion outer finisher
(LH)
4. Recline lever 5. Headrest holder (locked) 6. Headrest holder (free)
7. Headrest 8. Seat assembly
Driver side front seat bolt
torque: 40 Nm (4.1 kg-m, 30 ft-lb)
AWJIA0920ZZ
Revision: August 2015
2016 Versa Note
cardiagn.com
SE-22
< REMOVAL AND INSTALLATION >
FRONT SEAT
PASSENGER SIDE : Remo val and Installation
INFOID:0000000012432038
WARNING:
• Do not leave any objects (screwdriver s, tools, etc.) on the seat during repair. It can lead to personal
injury if the side air bag module should accidentally deploy.
• Always work from the side or back of th e seatback, do not work in front of seat.
• Do not use air tools or electric tools for servicing the seat assembly.
• Do not drop, tilt, or bump the si de air bag module while installing the seat. Always handle it with
care.
• After the side air bag module inflates, the front seat frame must be replaced.
• Before removing the front seat, tu rn the ignition switch OFF, disconnect both battery cables then
wait at least three minutes.
CAUTION:
When removing and inst alling the seat, use shop cloths to protect components from damage.
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to PG-70,
"Removal and Installation (Battery)".
2. Slide the seat to the full forward position.
3. Remove the seat rear bolts.
4. Slide the seat to the full rearward position.
5. Remove the seat front bolts.
6. Tilt the seat rearward and disconnect the harness connectors from the seat and remove.
INSTALLATION
Installation is in the reverse order of removal.
WARNING:
• Perform additional services when installing front passenger seat. Refer to SRC-39, "
ZERO POINT
RESET : Description".
• Zero point reset must be performed every time th e front passenger seat is removed from the vehicle.
• Zero point reset is done after the front passenger seat is installed in vehicle and all bolts are tight-
ened to specification.
CAUTION:
Make sure that the seat harness or the floor trim is not damaged during installation.
When installing the passenger side front seat, tighten the bolts in the
order shown.
7. Occupant classification system sen-
sors 8. Occupant classification system har-
ness 9. Occupant classification
system control unit
10. Seat belt buckle 11. Seat cushion outer finisher (LH)
Passenger side front seat
bolt torque: 40 Nm (4.1 kg-m, 30 ft-lb)
AWJIA0921ZZ
Revision: August 2015
2016 Versa Note
cardiagn.com
SE-24
< REMOVAL AND INSTALLATION >
REAR SEAT
7. Headrest holder (free)8. Seatback latch bracket (RH) 9. Seatback latch (RH)
10. Seatback frame (RH) 11. Seatback latch finisher (RH) 12. Seatback latch release knob
13. Seatback trim (RH) 14. Seatback pad (RH) 15. Seat cushion hook
16. Seat cushion 17. Seat cushion pad 18. Seat cushion trim
19. Cup holder 20. Armrest 21. Armrest hinge bracket
22. Armrest pivot bolt bushing 23. Armrest pivot bolt 24. Armrest hinge bracket finisher
(RH)
25. Bushing 26. Armrest hinge bracket finisher (LH) 27. Seatback pad (LH)
28. Seatback trim (LH) 29. Seatback latch finisher (LH) 30. Seatback frame (LH)
31. Seatback latch bracket (LH) 32. Seatback latch (LH) 33. Seatbelt guide finisher
34. Seat belt guide 35. Seatback (LH)
Pawl
Revision: August 2015 2016 Versa Note
cardiagn.com