2016 MITSUBISHI OUTLANDER PHEV Owner's Manual (in English)

ScreenCauseSolution (Reference)lThe Adaptive Cruise Control System
(ACC) is not available temporarily such
as for adhesion of contaminants to the sensor.
This is not a malfunction.l Refer to “How to use ACC” on page
7-49.l There is a fault in the Adaptive Cruise
Control System (ACC).l We recommend you to have it checked.
Refer to “Adaptive Cruise Control System
(ACC)” on page 7-43.l There is a fault in the Forward Collision
Mitigation System (FCM).l We recommend you to have it checked.
Refer to “Forward Collision Mitigation System (FCM)” on page 7-55.l FCM braking function of the Forward
Collision Mitigation System (FCM) hasbeen activated.l Refer to “FCM braking function” on page
7-57.l The Forward Collision Mitigation System
(FCM) is not available temporarily such
as for adhesion of contaminants to the
sensor.
This is not a malfunction.
Indication lamp, warning lamp, and information screen display list
6-33OGGE16E1Instruments and controls6

ScreenCauseSolution (Reference)lThe Lane Departure Warning (LDW) has
detected that your vehicle is about to
leave or has left the lane.l Refer to “Lane Departure Warning
(LDW)” on page 7-69.l The Lane Departure Warning (LDW) is
not available temporarily for too high a
temperature of the LDW camera.l There is a fault in the Lane Departure
Warning (LDW).l We recommend you to have it checked.
Refer to “Lane Departure Warning
(LDW)” on page 7-69.
Indication lamp, warning lamp, and information screen display list
6-34OGGE16E1Instruments and controls6

ScreenCauseSolution (Reference)lThe Ultrasonic misacceleration Mitigation
System sensor is temporarily not available for some reason such as the environmen-tal condition or increase of the sensor
temperature.l When the warning display does not disap-
pear after waiting for a while, contact a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Ultrasonic misacceleration Miti-
gation System” on page 7-63.l The Ultrasonic misacceleration Mitigation
System does not operate normally becausethere are some malfunctions in the sensor
or the system.l Immediately have your vehicle inspected
at a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Ultrasonic misacceleration Miti-
gation System” on page 7-63.
Indication lamp, warning lamp, and information screen display list
6-35OGGE16E1Instruments and controls6

ScreenCauseSolution (Reference)lThe Ultrasonic misacceleration Mitigation
System is activated.l Refer to “Ultrasonic misacceleration Miti-
gation System” on page 7-63.

Navigation information dis-
play*
E00531401061
On vehicles equipped with MITSUBISHI
Multi-Communication System (MMCS), the following information on navigation will be
displayed when guidance location such as junction and destination is approached after
you set the destination and started the route
guidance.
1- Guidance display
Indication lamp, warning lamp, and information screen display list
6-36OGGE16E1Instruments and controls6

Shows the direction of vehicle travel andthe guidance location.2- Remaining distance display Shows the distance to the location where
the guidance is displayed.NOTEl Please read this section and also the separate
owner’s manual for MITSUBISHI Multi-
Communication System (MMCS).
Indication lamp, warning lamp, and information screen display list
6-37OGGE16E1Instruments and controls6Direction of vehicle travel (Example) Destination Ferry terminal Tollbooth Intermediate destination (Example)

Other interrupt displays
E00524202080
ScreenSystem operation statusReferencelWhen you pressed the power switch and
the operation mode become the ACC
without depress the brake pedal, this
screen is displayed.
This screen will be displayed repeatedly at regular intervals while the operation mode of the power switch is put in ACC.l Place the select position in the “P” (PARK)
position, depress the brake pedal more
firmly than usual with the right foot. Then,
press the power switch.
Refer to “Starting and stopping the Plug-in Hybrid EV System” on page 7-11.l When Plug-in Hybrid EV System does
not start even if the operation mode of the power switch is put in ON, this screen is displayed.l When starting the Plug-in Hybrid EV Sys-
tem, you pressed the power switch with- out select position in the “P” (PARK) po-
sition.l Place the select position in the “P”
(PARK) position by pressing the electrical
parking switch, depress the brake pedal more firmly than usual with the right foot.
Then, press the power switch.
Refer to “Starting and stopping the Plug- in Hybrid EV System” on page 6-36.l Driving power is restricted by the safety
system as the Plug-in Hybrid EV System
has become too hot or too cold.l You do not have to take any actions. The
restriction on the driving power will be re- leased when the Plug-in Hybrid EV Sys- tem returns to the normal temperature.
Indication lamp, warning lamp, and information screen display list
6-38OGGE16E1Instruments and controls6

ScreenSystem operation statusReferencelIf the vehicle had not been refueled about
15 litres or more at one time for threemonths, the engine starts automatically
for the maintenance of the engine or the fuel system components.
This display may appear frequently de-
pending on the use conditions of your ve- hicle such as when fuel has been staying
in the fuel tank for a long time.
When the engine is running, this display shows the state where the drive battery is
charged, and the battery charge mode dis-
play (
) is displayed.
But the drive battery will not be full charge.
l Refill the 15 litres more at one time. This
display and battery charge mode display will disappear, and the engine will stop.
If the fuel remaining display will be be-
low half, you can refill the fuel more than 15 litres certainly.
l If you cannot refill the fuel due to large
amount of the remaining fuel, operate the
vehicle without the normal charging or the quick charging.l The accelerator pedal has been depressed
when the select position is in the “N”
(NEUTRAL) position.l When you start the vehicle, be sure to
check the select position indicator and make sure the select position is in the “D”(DRIVE) or “R” (REVERSE) position.
Then, please depress the accelerator ped-
al.
Refer to “Select Position indicator” on page 7-14.l The selector lever has been operated when
the select position is in “P” (PARK) posi-
tion and the brake pedal is not depressed.l Operate the selector lever while depressed
firmly on the brake pedal.
The operation status of each system is displayed on the information screen. Refer to the appropriate page for the system for further details.
Indication lamp, warning lamp, and information screen display list
6-39OGGE16E1Instruments and controls6

ScreenSystem operation statusReferencelWhen charging of the drive battery is
completed.l Refer to “Charging” on page 3-02.lWhen the mode is changed by the opera-
tion of the 4WD lock switch or ECO mode
switch.l Refer to “ECO mode switch” on page
6-53.
l Refer to “4WD lock switch” on page
7-18.
l Refer to “When the ECO mode switch is
ON” on page 7-19.
Indication lamp, warning lamp, and information screen display list
6-40OGGE16E1Instruments and controls6