2016 MITSUBISHI LANCER door lock

Door
locks
5-36
Features and controls
5
2.Be
sure
the
keys
are
not
inside
the
vehi-
cle. Close the doo
r.
N0054960
0178
Type 1
Type 2
If
the
ignition
switch
is
turned
off and
the
driver
’s door
is opened
with
the
key
in
the
ignition
switch,
the
key
reminder
buzzer
will
sound
intermittently
to remind
you
to remove
the k
ey.
The
warning
display
will
be
displayed
on
the
information
screen
in
the
multi-information
display
.
N0051730
0039
When
you
push
the
lock
knob
forward
or lock
the
door
with
the
power
door
lock
switch
in
both
of
the
following
conditions,
the
lock
knob
will
automatically
return
to
the
unlocked position.The
key
is in
the
ignition
switch
or
the
ignition
switch
is in
the
“ACC”
or
“ON”
position.Driver
’s door
or
front
passenger
door
is
opened.
N0050380
0121
Type 1
Type 2
If the
driver
’s door
is opened
while
the
igni-
tion
switch
is
in
a
position
other
than
“LO
CK
” (PUSH
OFF),
the
ignition
switch
return
reminder
buzzer
will
sound
intermit-
tently
to
remind
you
to
return
the
ignition
switch to the “LOCK” (PUSH OFF) position. The
warning
display
will
be
displayed
on
the
information
screen
in
the
multi-information
display
.
Key r
eminder system
When a key was used to start the engine
Lock out pr
otection
Ignition
switch
return
reminder
system When
the
F.A.S.T
.-key
was
used
to
start
the
engine

Power door locks
Features and controls
5-37
5
N00509300
564
All of the
doors
can
be
locked
or unlocked
by
pressing
the
power
door
lock
switch
on
the
driver
’s or the front passenger
’s door
.
Turn
the
key
in the
driver
’s door
lock
once
in
the
unlocking
direction,
and
the
driver
’s door
will be unlocked.
Power
door
locks
NOTE
When
locking
or unlocking
with
the
key
on
the driver’s door
, onl
y the driver’s door
will
lock or unl
ock.
Repeated
continuous
ope
ration
betw
een
lock
and
unl
ock coul
d activ
ate
the powe
r door
locking
systems
built-
in protection
circuit
and
pre
vent the system
from
ope
rating.
If
this occurs,
wait
about
1 minute
before
ope
r-
ating
the inside lock knob
or the key.
To lock and unlock the doors Using the power door lock switch 1-
Lock
2-
Unlock
Using the key 1-
Insert or remove the emer
gency key
.
2-
Lock
3-
Unlock

“Child safety locks”
for
rear door
5-38
Features and controls
5
N005177
01144
All
doors
will
unlock
when
the
ignition
switch is turned to the “LOCK” position. All
doors
will
unlock
when
the
selector
lever
is moved to the “P” (P
ARK) position with the
ignition switch in the “ON” position.
N0050940
0190
Child
safety
locks
help
prevent
rear
passen-
gers,
especially
children,
from
opening
the
rear door using the inside door handle. A lock
lever
for
the
child
safety
lock
is pro-
vided on each rear doo
r.
When
the
lever
is in the
lock
position
(1),
the
rear
door
cannot
be
opened
using
the
inside
door h
andle.
To open
the
rear
door
when
the
child
safety
lock
lever
is in the
lock
position,
pull
the
out-
side door handle.When
the
lever
is in the
release
position
(2),
the
child
safety
lock
is released
and
the
rear
door
can
be
opened
using
the
inside
door
han-
dle.
To unlock the doors You can
select
either
the
function
to unlock
the
doors
using
the
ignition
switch
position
or the
function
to unlock
the
doors
using
the
selector
lever
{continuously
variable
trans-
mission (CVT)} position.These
functions
are
not
activated
when
the
vehicle
is shipped
from
the
factory
. To acti-
vate
or
deactivate
these
functions,
please
contact
your
authorized
Mitsubishi
Motors
deale
r.
Using the ignition switch position Using the selector lever {continu- ously variable transmission (CVT)}
position
“Child
safety
locks”
for
rear
door 1-
To lock
2-
To release
W
AR
NING
Always
keep
the
doors
tightly
closed
and
locked
when
driving.
An
unlocked
door
may
be
accidentally
opened
by
a passen-
ger
, especially
by
a child
who
could
fall
out. Also, if the doors a
re not locked, ther
e
is a greater
risk
of someone
being
thr
own
from the vehicle in an accident.

Theft-alarm system
Features and controls 5-41
5
To open the trunk from the inside, move the lever (A) in the direction of the arrow on the lever. Push up on the trunk lid to open the trunk and climb out.
N00510200185
The theft-alarm system is designed to provideprotection from unauthorized entry into the vehicle. This system is operated in three stages: the first is the “armed” stage, the sec-ond is the “alarm” stage,
and third is the “dis-
armed” stage. If triggered, the system provides both audible and visual alarm sig-nals.
N00510301183
Park the vehicle and stop the engine. Arm the system as described below.
1. Turn the ignition switch to the “LOCK” position. Also, if a key was used to start the engine, remove the key from the ignition switch.2. Make sure that the trunk lid and engine hood are closed. 3. Lock all doors by either the remote con-trol transmitter or the F.A.S.T.-key. At this time, the theft-alarm indicator (A) on the audio panel flashes for confirma-tion.
WA R N I N G Children should never be left unsuper- vised in or around vehicles. Unsupervised children could lock them- selves in an open vehicle or trunk. People trapped inside a vehicle or trunk, even if only for a short period of time, canquickly die from suffocation or heat stroke, especially on hot days. Interior temperatures in vehicles can rise in min-utes. Keep your vehicle doors locked and the trunk lid closed when not in use. Keep your vehicle keys away from children.
CAUTION When loading the trunk, place your things so that they will not touch the emergency trunk lid release lever when you close the trunk. Otherwise you could damage the lever and make it unusable.
Theft-alarm system
CAUTION Do not modify or add parts to the theft-alarm system. Doing so could cause the theft-alarm to malfunction.
Armed stage
Arm the system and leave
BK0230300US.bo
ok 41 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Theft-alarm system 5-42 Features and controls
5
4. The system has entered the armed stage after about 20 seconds, when the theft- alarm indicator (A) flashing becomes slower.The theft-alarm indicator (A) continues to flash while the system is in the armed stage.
N00510401197
The alarm will be activated if any of the fol-lowing occur while the vehicle is parked andthe system is armed.
 One of the doors is opened without using the remote control transmitter or the F. A . S . T. - k e y.  The engine hood or the trunk lid is opened.
When the alarm is activated: 1. The headlights blink on and off for 3 min- utes.After 3 minutes the headlights automati- cally shut off. 2. The horn will sound intermittently for 3minutes.
Ty p e 1 Ty p e 2 The alarm can be deactivated in the following ways.
NOTE
 If the engine hood or the trunk lid is open, the theft-alarm indicator (A) illuminates and the system cannot enter the armed stage. The system enters the armed stage about 20 sec-onds after the engine hood or the trunk lid is closed.  The system will be disarmed if, while the theft-alarm indicator (A) is illuminated, all doors are unlocked by remote control trans-mitter or the F.A.S.T.-key.  The system will be disarmed if, while the theft-alarm indicator is illuminated, the igni- tion switch is turned to the “ON” position.  The system will not be
armed if a door or the
trunk lid or the engine hood is not com- pletely closed. If this happens, rearm the sys-tem as described above.
Alarm stage
Type of alarm Horn sounds!Headlights blink on and off!
NOTE
 The alarm will continue to operate for 3 min- utes. At the end of that period, the alarm will automatically shut off to save battery power. The system will then
be rearmed until the
proper disarming step is taken.  The alarm will resume if unauthorized actions are taken again, even if the alarm hasstopped.  While the alarm is operating, a warning is displayed on the information screen in the multi-information display.
Alarm deactivation
BK0230300US.bo
ok 42 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Power windows
Features and controls 5-43
5
 By using the remote control transmitter or the F.A.S.T.-key to lock or unlock the door.  Turn the ignition switch to the “ON” posi- tion.
N00510501169
The system will be disarmed if the followingoperation is performed.  The ignition switch is turned to the “ON” position.  All doors are unlocked by the remote con- trol transmitter or the F.A.S.T.-key.
N00510601128
Use the following procedure to test the sys-tem: 1. Lower the driver’s window. 2. Arm the system as explained in “Armed stage”. 3. Make sure that the theft-alarm indicatorcomes on and flashes for approximately 20 seconds. 4. Wait a few seconds and then unlock thedriver’s side door by using the inside door lock knob and open the door. 5. Check to be sure that the horn soundsintermittently and the headlights blink on and off when a door is opened. 6. Disarm the system by unlocking all doorsby the remote control transmitter or the F. A . S . T. - k e y.
N00510800367
Disarmed stage
NOTE
 If the UNLOCK button is pressed when all doors are closed and no door is openedwithin approximately 30 seconds, re-arming will automatically occur.Disarm...by remote control transmitter or F. A . S . T. - k e y
 The amount of time after unlocking until the vehicle relocks automatically can be adjusted. See an authorized Mitsubishi Motors dealer for details.  Once the system has been disarmed, it can- not be rearmed except by repeating the arm- ing procedure.
Testing the theft-alarm system
NOTE
Power windows 1- Open (down) 2- Close (up)
NOTE
 Never try to operate the main switch and sub switch in different directions at the sametime. This will freeze the window in posi- tion.  Operating the power windows repeatedly with the engine stopped will run down the battery. Use the window switches only whilethe engine is running. WA R N I N G Before operating the power windows, make sure that nothing can be trapped(head, hands, fingers, etc.) in the window.
BK0230300US.bo
ok 43 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Power windows 5-44 Features and controls
5
The main switch located on the driver’s door can be used to operate all door windows. A window can be opened or closed by operat-ing the corresponding switch.Press the switch down to open the window, and pull up the switch to close it. If the driver’s door window switch is fullypressed down/pulled up, the driver’s door window automatically opens/closes com- pletely.If you want to stop the window movement, operate the switch lightly in the reverse direc- tion.
Each sub switch can be used for its own pas- senger door window, unless the driver’s win-dow lock switch is activated. The power windows can be run up or down when the ignition switch is in the “ON” posi- tion. The door windows can be opened or closedfor a 30 second period after the ignition switch is turned to the “ACC” or “LOCK” position. However, once the driver’s door orthe front passenger’s door is opened, the power windows cannot be operated.
 Never leave the vehicle with the key in the ignition switch.  Never leave a child alone in the vehicle.
Main switch
WA R N I N G
1- Driver’s door window switch 2- Front passenger door window switch 3- Left rear door window switch 4- Right rear door window switch 5- Window lock switch
Sub switch 1- Close (up)2- Open (down)Timer function
BK0230300US.bo
ok 44 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Power windows
Features and controls 5-45
5
N00528800092
If a hand or head is trapped, for safety the door window is automatically lowered a little. After the door window is lowered, pull up the switch again to close the door window.
N00549000127
When this switch is in the lock mode, themain switch for passenger door window andthe sub switch cannot be used to open or close the door window, and the main switch will open or close only the driver’s door win-dow. To unlock the switch, press it again.
Safety mechanism (Driver’s door window only)
WA R N I N G If the safety mechanism is activated three or more times successively, the safetymechanism will be temporarily cancelled. If a hand or head subsequently gets trapped, a serious injury can result.CAUTION The safety mechanism is deactivated just before the door window closes. This allows the door window to close completely. There-fore be especially careful that fingers are not trapped in the door window opening. The safety mechanism is deactivated while the switch is pressed. Therefore be especially careful that fingers are not trapped in the door window opening. Do not deliberately trap your hands or head in order to activate the safety mechanism. Your hand or head could be trapped and per-sonal injury could result.
NOTE
 The safety mechanism can be activated if the driving conditions or other circumstances cause the door window to be subjected to a physical shock similar to that caused by trapped hand or head.  If the safety mechanism is activated 3 or more times consecutively, the safety mecha-nism is deactivated and
normal closing of the
door window will be aborted. Use the following method to return to normaloperation. 1. If the door window is open, repeatedly pull up the power window switch to fully close the door window. 2. With fully closing the window, release the switch and then pull up the switch again for about 1 second.
Lock switch 1- Lock 2- UnlockWA R N I N G Before driving with a child in the vehicle, be sure to lock the window switch to makeit inoperative. Children tampering with the switch could easily trap their hands or heads in the window.
BK0230300US.bo
ok 45 ページ ２０１５年７月３０日　木曜日　午後８時３８分