2016 MITSUBISHI LANCER brake

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)5-22
Features and controls
5
1.Make
sure
that
all electric
devices,
such
as
lights,
air
conditioning
blower
and
rear
window defogger
, are turned o
ff.
2.While
depressing
the
brake
pedal
on
vehi-
cles
equipped
with
continuously
variable
transmission
(CVT)
or the
clutch
pedal
on
the
vehicles
equipped
with
manual
trans-
axle,
press
the
accelerator
pedal
halfway
and
hold
it there,
then
crank
the
engine.
Release
the
accelerator
pedal,
immedi-
ately after the engine starts.3.If the
engine
still
will
not
start,
the
engine
could
be
flooded
with
too
much
gasoline.
While
depressing
the
brake
pedal
on
vehi-
cles
equipped
with
CVT
or
the
clutch
pedal
on
the
vehicles
equi
pped
with
man-
ual
transaxle,
push
the
accelerator
pedal
all
the
way
down
and
hold
it there,
then
crank
the
engine
for
5
to
6
seconds.
Return
the
ignition
switch
to the
“LOCK”
position
and
release
the
accelerator
pedal.
Wait
a few
seconds,
and
then
crank
the
engine
again
for
5 to
6 seconds
while
depressing
the
brake
pedal
or
the
clutch
pedal,
but
do
not
push
the
accelerator
pedal.
Release
the
ignition
key
if
the
engine
starts.
If the
engine
fails
to
start,
repeat
these
procedures.
If the
engine
still
will
not
start,
contact
your
local
Mitsubi-
shi
Motors
dealer
or
a repair
facility
of
your choice for assistance.
When
the
ambient
temperature
is
-4°F
(-20°C)
or
lower
, it may
not
be
possible
to
start
from
a standstill
even
with
the
selector
lever
in
the
“D”
(DRIVE)
or
“R”
(REVERSE) position.This
phenomenon
occurs
because
the
trans-
axle
has
not
warmed
up
suf
ficiently;
it does
not
indicate
a problem.
If this
occurs,
place
the
selector
lever
in the
“P”
(PARK)
position
and let the engine idle for at least 10 minutes.The
transaxle
will
warm
up,
and
you
will
be
able to drive normally
.
Do
not
leave
the
vehicle
during
warm-up
operation.
N0051480
0020
N0051520
0148
The
emer
gency
key
is built
into
the
F.A.S.T
.-
key
.
When
the
F.A.S.T
.-key
cannot
be
used,
such
as when
the
battery
of the
F.A.S.T
.-key
or the
vehicle
has
run
down,
the
emer
gency
key
can
be
used
to
lock
and
unlock
the
driver
’s door
and to start the engine. To use
the
eme
rgency
key
(1),
unlock
the
lock
knob
(2)
and
remove
it from
the
F.A.S.T
.-key
(3). Turn
the
emer
gency
key
toward
the
front
of
the
vehicle
to
lock
the
door
. After
checking
that
the
door
is locked,
turn
the
emer
gency
key back to the center and remove it.
Startability
of
continuously
variable
transmission
(CVT)
vehicles
at extr
emely
cold ambient temperatur
e
To operate
using
the
emergency
key

Emergency
key

NOTE
Onl
y use
the emer
gency key in an emer
-
gency
. When
the
battery
of the
F.A.S.T
.-key
has
run
dow
n, replace
the
battery
as soon
as
possible
and
use
it as a F.A.S.T
.-key
again.
After
using
the emer
gency key, be sure
to
reinse
rt it into the F.A.S.T
.-ke
y.
To lock
or
unlock
the
driver
’s door
with
the emergency key

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)5-24
Features and controls
5
1.[For vehicles with manual transaxle]Push
the
emer
gency
key
in at the
“ACC”
position
and
keep
it depressed
until
it is
turned
to
the
“LOCK”
position,
and
remove. [For
vehicles
with
continuously
variable
transmission (CVT)]First,
set
the
selector
lever
to
the
“P”
(PARK)
position,
and
then
slowly
turn
the
ignition
switch
to
the
“LOCK”
position
while
pressing
it.
2.Install the cover of the ignition switch.3.Reinsert
the
emer
gency
key
into
the
F.A.S.T.-key.
Steering wheel lock
NOTE
When
the
ignition
switch
cannot
be
turned
from
the “LOCK”
position
to the “ACC”
position,
turn
the ignition
switch
while
turn-
ing
the steer
ing
wheel
in bot
h directions.
To turn fr
om “ACC” to “LOCK”
NOTE
For
vehicles
with
CVT, the
emer
gency
key
cannot
be remove
d unless
the selector
lev
er
is set
to the “P” (PARK) position.
NOTE
Always
install
the
cover
of
the
ignition
switch
when
not
using
the
emer
gency
key
.
Not
doing
so could
cause
damage
if foreign
mater
ial
such
as dust gets into the keyhole
of
the
ignition
switch.
CAUTIONDo
not
turn
the ignition
switch
to the LOCK
position
while
the vehicle
is movi
ng.
This
will cause
the steer
ing
wheel
to lock, mak
ing
it impossible to operate the vehicle. If the
engine
is stopped
while
driving,
the
pow
er
brake
boos
ter
will
stop
functioning
and
greater
effort
for
braking
will
be
requi
red.
Also,
the powe
r steer
ing
system
will
not
function
and
it will
requi
re greater
effort
to manually steer
the vehicle.
Do
not
leav
e the ignition
switch
in the “ON”
position
for
a long
time
whe
n the engi
ne is
not
runni
ng.
The battery will run down.
Do
not
turn
the ignition
switch
to the
“START” position
whe
n the engi
ne is run-
ning.
It will damag
e the starter motor.

Free-hand Advanced Security Transmit
ter (F.A.S.T.-key) (if so equipped)
Features and controls
5-25
5
Turn
the
eme
rgency
key
to the
“LO
CK
” pos
i-
tion.Turn the steering wheel until it is locked.Turn
the
emer
gency
key
to
the
“ACC”
posi-
tion
while
moving
the
steering
wheel
slightly
.
Tips for starting
Do not
operate
the
starter
motor
continu-
ously
for
longer
than
15
seconds
as
this
could
run
the
battery
down
or damage
the
starter
motor
. If the
engine
does
not
start,
turn
the
eme
rgency
key
back
to
the
“LO
CK
” pos
ition,
wait a few
seconds
,
and
then
try
again.
Trying
repeatedly
with
the
engine
or
starter
motor
still
turning
will damage the starter mechanism.If the
engine
will
not
start
because
the
bat-
tery
is
weak
or
dischar
ged,
refer
to
“Jump-starting
the
engine”
on
page
8-2
for instructions.A longer
warm
up
period
will
only
con-
sume
extra
fuel.
The
engine
is warmed
up
enough
for
driving
when
the
bar
graph
of
the
engine
coolant
temperature
display
starts
to move.
Refer
to “Interrupt
display
screen
(W
ith
ignition
switch
in the
“ON”
position)” on page 5-101.
Starting the engineYour
vehicle
is equipped
with
an
electroni-
cally
controlled
fuel
injection
system.
This
is
a system
that
automatically
controls
the
fuel
injection.
There
is
no
need
to
depress
the
accelerator pedal when starting the engine.The starter
mo
tor sho
uld
not
be run
for
mo
re
than
15
seconds
at a time.
To prevent
battery
drain,
wait
a few
seconds
between attempts to restart the engine.1.Make
sure
all
occupants
are
properly
seated with seat belts fastened.2.Make sure the parking brake is applied.3.While
pushing
the
lock
release
buttons
(A),
remove
the
cover
of
the
ignition
switch.
To lock
To u
nlock
CAUTIONRemove
the emer
gency key whe
n leav
ing
the
vehicle.
If your
vehicle
needs
to be
towed,
turn
the
emer
gency
key to the
“ACC”
position
to
unlock the steering wheel.NOTE
If the
front
wheels
are
turned,
the
anti-theft
lock
may
sometimes
make
it difficult
to turn
the
emer
gency
key
from
“LO
CK” to “ACC”.
Firmly
turn
the steer
ing
wheel
to the left or
to the right
as you t
urn
the emer
gency ke
y.
Starting
W
AR
NING
Never
run
the engin
e in a clos
ed or poorly
ven
tilated
area
any lon
ger
than is need
ed
to move
you
r veh
icle
out of the area.
Car-
bon
monoxi
de gas,
which
is odorless
and
extr
emely
poi
sonous,
coul
d build
up
and
cause
serious
injur
y or
death.
CAUTIONDo not push-star
t the vehicle.
Do
not run
the engin
e at high
rpms
or drive
at high
speeds
until
the
engine
has
had
a
chance to
warm up.
Releas
e the
emer
gency
key
as soon
as the
engine
starts
. It
will
damage
the
starter
motor.
CAUTION

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)5-26
Features and controls
5
4.Insert
the
emer
gency
key
into
the
ignition
switch.5.Insert
the
F.A.S.T
.-key
into
the
emer
gency
key
.
6.Press
and
hold
the
brake
pedal
down
firmly with your right foot.7.Press
and
hold
the
clutch
pedal
all
the
way
down
(manual
transaxle).
8.On
vehicles
with
manual
transaxle,
place
the
gearshift
lever
in
the
“N”
(Neutral)
position. On
vehicles
with
CVT
, make
sure
the
selector
lever
is in
the
“P”
(PARK)
posi-
tion.
9.Turn
the
emer
gency
key
with
the
F.A.S.T
.-key
to
the
“ON”
position
and
make
certain
that
all
warning
lights
and
warning
displays
are
functioning
properly
before starting the engine.
10.
Turn
the
emer
gency
key
with
the
F.A.S.T.-key
to
the
“START”
pos
ition
without
pressing
the
accelerator
pedal.
Release
the
emer
gency
key
with
the
F.A.S.T
.-key when the engine starts.
11.Remove
the
F.A.S.T
.-key
from
the
emer
-
gency key
.
NOTE
For
models
equipped
with
a manual
trans
-
axle,
the
starter
will
not
operate
unless
the
clu
tch
pedal is fully
depre
ssed (Cl
utch
inter-
lock). This is a safety feature.
NOTE
On
vehicles
with
continuously
variable
trans
mission
(CV
T),
the
starter
will not
oper
-
ate
unless
the
selector
lever
is in
the
“P”
(PARK)
position
or
the
selector
lever
is in
the “N” (NE
UTRA
L) position
with
the brake
pedal depr
essed.
For s
afety
reas
ons, s
tart the eng
ine in t
he “P”
(PARK)
position
so
that
the
wheels
are
locked.NOTE
Minor
noi
ses may
be heard
on
engi
ne start-
up.
These will disappear
as the engi
ne warms
up.

Free-hand Advanced Security Transmit
ter (F.A.S.T.-key) (if so equipped)
Features and controls
5-27
5
After
several
attempts,
you
may
experience
that the engine still does not start.1.Make
sure
that
all
electric
devices,
such
as
lights,
air
conditioning
blower
and
rear
window defogger
, are turned of
f.
2.While
depressing
the
brake
pedal
on
vehi-
cles
equipped
with
continuously
variable
transmission
(CVT)
or the
clutch
pedal
on
the
vehicles
equipped
with
manual
trans-
axle,
press
the
accelerator
pedal
halfway
and
hold
it there,
then
crank
the
engine.
Release
the
accelerator
pedal,
immedi-
ately after the engine starts.3.If the
engine
still
will
not
start,
the
engine
could
be
flooded
with
too
much
gasoline.
While
depressing
the
brake
pedal
on
vehi-
cles
equipped
with
CVT
or
the
clutch
pedal
on
the
vehicles
equipped
with
man-
ual
transaxle,
push
the
accelerator
pedal
all the
way
down
and
hold
it there,
then
crank
the
engine
for
5
to
6
seconds.
Return
the
ignition
switch
to the
“LOCK”
position
and
release
the
accelerator
pedal.
Wait
a few
seconds,
and
then
crank
the
engine
again
for
5 to
6 seconds
while
depressing
the
brake
pedal
or
the
clutch
pedal,
but
do
not
push
the
accelerator
pedal.
Release
the
ignition
key
if
the
engine
starts.
If the
engine
fails
to
start,
repeat
these
procedures.
If the
engine
still
will
not
start,
contact
your
local
Mitsubi-
shi
Motors
dealer
or
a repair
facility
of
your choice for assistance.
When
the
ambient
temperature
is
-4°F
(-20
°C)
or
lower
, it may
not
be
possible
to
start
from
a standstill
even
with
the
selector
lever
in
the
“D”
(DRIVE)
or
“R”
(REVERSE) position. This
phenomenon
occurs
because
the
trans-
axle has
not warmed
up sufficiently
; it does
not
indicate
a problem.
If this
occurs,
place
the
selector
lever
in the
“P”
(PARK)
position
and let the engine idle for at least 10
minutes.
The
transaxle
will
warm
up,
and
you
will
be
able to drive normally
.
Do
not
leave
the
vehicle
during
warm-up
operation.
N00529600
101
The
electronic
immobilizer
is designed
to sig-
nificantly
reduce
the
possibility
of
vehicle
theft.
The
purpose
of
the
system
is to immo-
bilize
the
vehicle
if
an
invalid
start
is
attempted.
A valid
start
attempt
can
only
be
achieved
(subject
to certain
conditions)
using
a F.A.S.T
.-Key
“registered”
to
the
immobi-
lizer system.
W
AR
NING
Mak
e sur
e to
remove
the F.A.S.T.-key
from
the
emergency
key
after
the
engine
is
start
ed.
If not
removed,
the
F.A.S.T
.-key
could
fall
to
the
floor
, which
may
interf
ere with
pedal
operati
on.
Furthermor
e, the
F.A.S.T
.-ke
y coul
d pre-
vent
the
driv
er’s knee
airbag
from
inflat-
ing
normally
or
could
be
propelled
to
cause serious injury if the airbag inflates.NOTE
When
using
the
emer
gency
key
to start
the
engine,
firs
t remove
the
key
from
the
key
holder
. If the
emer
gency
key
is attached
to a
key holder
(key
ring), it may
beco
me
impos-
sible
to insert
the
keyless
operation
key
into
the emer
gency key, and
it may
pre
vent the
engi
ne from
being
started.
When the engine is hard to start
Startability
of
continuously
variable
transmission
(CVT)
vehicles
at extr
emely
cold ambient temperatur
e
Elect
ronic immobilizer (Anti-
theft starting system)

Parking brake 5-48 Features and controls
5
N00511401439
To park the vehicle, first bring it to a com- plete stop and fully engage the parking brake.For vehicles with a manual transaxle, move the gear shift lever to 1st (on a uphill) or “R” (Reverse) (on a downhill) position.For vehicles with a continuously variable transmission (CVT), set the selector lever to “P” (PARK) position.
When parking on a hill, apply the parking brake and turn the front wheels toward thecurb on a downhill grade, away from the curb on an uphill grade.
 Be sure to close the sunroof completely when washing the vehicle or when leaving the vehicle.  Do not put any wax on the weatherstrip (black rubber) around the sunroof opening. If it is waxed, the weatherstrip cannot maintain a weatherproof seal with the sunroof.  After washing the vehicle or after rain be sure to wipe off any water that is on the sun-roof before operating it.  Operating the sunroof repeatedly with the engine turned off will run down the battery. Operate the sunroof only while the engine is running.
Parking brake
NOTE
To apply 1- Pull the lever up without pushing the
button at the end of hand grip. When the parking brake is set and theignition switch is in the “ON” position, the brake warning light in the instru- ment cluster will come on. Before driving, be sure to release the parking brake.
To r e l e a s e 1- Pull the lever up slightly. 2- Push and hold the button at the end of
the hand grip.
3- Push the lever downward.
BK0230300US.bo
ok 48 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Steering wheel tilt lock lever Features and controls 5-49
5
N00511500215
To adjust the steering wheel height, release the tilt lock lever while holding the steeringwheel by hand, and raise or lower the steering wheel to the desired height. After adjustment, securely lock the lever bypulling it upward.
CAUTION Before driving, be sure that the parking brake is fully released and brake warning light is off. If you drive without the parking brake fully released, the warning display will appear onthe information screen in the multi-informa- tion display. If a vehicle is driven without releasing theparking brake, the brakes will be overheated, resulting in ineffective braking and possible brake failure. Warning light Warning display type 1 Warning display type 2
Steering wheel tilt lock lever 1- Locked 2- ReleasedWA R N I N G After adjusting, make sure the lock lever is secured in the locked (1) position. Type 1 Type 2
 Do not attempt to adjust the steering wheel while driving. This can be danger- ous. When releasing the tilt lock lever {moving it to the position (2)}, be sure to hold the steering wheel firmly. Otherwise, the steering wheel may slip down too sud-denly. WA R N I N G
BK0230300US.bo
ok 49 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Steering wheel lock 5-54 Features and controls
5
position, and then turn the key to the “LOCK” position and remove it.
N00512500195
[For vehicles equipped with the F.A.S.T.-key]For information on operations for vehicles equipped with the F.A.S.T.-key, refer to “F.A.S.T.-key: Steering wheel lock” on page5-20. [Except for vehicles equipped with the F. A . S . T. - k e y ]
Remove the key at the “LOCK” position. Turn the steering wheel until it is locked. Turn the key to the “ACC” position while moving the steering wheel slightly.
NOTE
 For vehicles with a CVT, the key cannot be removed unless the selector lever is set to the“P” (PARK) position, wh
ich allows the igni-
tion switch to turn to the “LOCK” position.CAUTION Do not remove the ignition key from the ignition switch while driving. The steering wheel will lock, causing loss of control. If the engine is turned off while driving, the power brake booster will stop functioning and braking efficiency will be reduced. Also,the power steering system will not function and it will require greater effort to manually steer the vehicle.CVT
 Do not leave the key in the “ON” position for a long time when the engine is not running. This will cause the battery to run down. Do not turn the key to the “START” position when the engine is running. It will damage the starter motor.
Steering wheel lock
CAUTION
To l o c k To u n l o c k
CAUTION Remove the key when leaving the vehicle.NOTE
If the front wheels are turned, the anti-theft lock may sometimes make it difficult to turn the key from “LOCK” position to “ACC” position. Firmly turn the steering wheel tothe left or to the right as you turn the key.
BK0230300US.bo
ok 54 ページ ２０１５年７月３０日　木曜日　午後８時３８分