2016 MERCEDES-BENZ SL-Class display

Updating the digital map
Important safety notes
GWARNING
Combustion engines emit poisonous exhaust
gases such as carbon monoxide. Inhaling
these exhaust gases leads to poisoning. There
is a risk of fatal injury. Therefore never leave
the engine running in enclosed spaces with-
out sufficient ventilation.
Introduction
The digital maps generated by the map soft-
ware become outdated in the same way as
conventional road maps. Optimal route guid-
ance can only be provided by the navigation
system in conjunction with the most up-to-
date map software.
Information about new versions of the digital
map can be obtained from an authorized
Mercedes-Benz Center. You can have the dig-
ital map updated there with a DVD, or you can
update it yourself.
Carrying out a manual update
iThe update process can take a long time
(over an hour), depending on the size of the
digital map. During this time, you will only
be able to switch on radio mode and to
accept incoming calls. The update will be
completed more quickly if the vehicle is
stationary.
If you start the update with the engine
switched off and the starter battery has
insufficient power, COMAND may automat-
ically switch off. This protects the battery. If
this occurs, restart the update with the
engine running.
XInsert the DVD (Ypage 447).
COMAND checks whether the digital map
on the DVD is compatible with the naviga-
tion system and system software.
A prompt then appears asking if you want
to install the database. Versions of the database currently installed and the data-
base that is to be installed are displayed.
XSelect
YesorNoand press Wto confirm.
After selecting Yes
, an activation code
must be entered when installing a database
for the first time. You will receive the acti-
vation code when you buy the navigation
DVD.
If you select No
, the process will be can-
celed.
XEnter the activation code.
After entering the activation code cor-
rectly, COMAND starts updating the digital
map. Once the update is finished, you will
see a message.
XTo confirm the message: pressWthe
COMAND controller.
XTake the DVD out of the slot.
While the update is running, you will see a
message to this effect and a progress bar.
The navigation system is not operational
until the update is complete.
iYou cannot eject the DVD during the
update. If you switch off COMAND during
the update, the update is interrupted. It
then continues from where it was interrup-
ted when the system is restarted.
COMAND may prompt you to change the DVD
during the update.
XPress the 8load/eject button.
XTake the DVD out of the slot.
XInsert the requested DVD.
Once the update has been successfully
completed, you will see a message to this
effect.
XTo confirm the message: pressWthe
COMAND controller.
XTake the DVD out of the slot.
The update is complete.
If the update is not successfully completed,
you will see a message that the map update
is not possible.
Navigation377
COMAND
Z

Problems with the navigation system
ProblemPossible causes/consequences andMSolutions
COMAND is unable to
continue route guid-
ance after the journey
has been interrupted.Route guidance is canceled if you interrupt the journey for more
than two hours.
"Interrupting the journey" refers to stopping the vehicle.
"Continuing route guidance" refers to switching COMAND back on
and driving on.
XContinue route guidance (Ypage 351).
ProblemPossible causes/consequences andMSolutions
COMAND is unable to
determine the vehicle's
position.COMAND has to redetermine the position of the vehicle if the
vehicle has been transported.
Example:
RAfter transporting the vehicle by ferry
RAfter transporting the vehicle by motorail
RAfter the vehicle has been towed
XStart the vehicle and pull away.
COMAND determines the vehicle's position. Depending on the
driving situation, this may take some time.
Route guidance may be restricted during the determination of
the vehicle's position.
When positioning is complete, route guidance is resumed with
navigation announcements and route guidance displays.
Navigation379
COMAND
Z

In preparation for telephoning via the Blue-
tooth®interface, you should check the fol-
lowing items on your mobile phone (see the
mobile phone operating instructions):
RHands-Free Profile
The mobile phone must support Hands-
Free Profile 1.0 or above.
RBluetooth®visibility
On certain mobile phones, the device itself
must be made "visible" to other devices, as
well as activating the Bluetooth
®function
(see the mobile phone operating instruc-
tions).
This visibility is for restricted periods of
time on some mobile phones.
RBluetooth®device name
Every Bluetooth
®device has its own Blue-
tooth®device name. This device name is
freely definable, but can be identical for all
devices from the same manufacturer. It is
therefore recommended that you change
this name so that you can easily recognize
your mobile phone (see the mobile phone
operating instructions).
iNot all mobile phones available on the
market are equally suitable. You can obtain
more detailed information about suitable
mobile phones and about connecting Blue-
tooth
®-capable mobile phones to
COMAND on the Internet at
http://www.mbusa-mobile.com. Or call
the Mercedes-Benz Customer Assistance
Center at 1-800-FOR-MERCedes
(1-800-367-6372) (for the USA) or Cus-
tomer Relations at 1-800-387-0100 (for
Canada).
iSome displays (e.g. the signal strength)
depend on the supported version of the
Hands-Free Profile.
Connecting a mobile phone
General information
Before using your mobile phone with
COMAND for the first time, you will need to:
Rsearch for it (Ypage 384) and then
Rauthorize (register) it (Ypage 385).
When you authorize a new mobile phone, it is
connected automatically.
You can authorize up to 15 mobile phones.
If the mobile phone supports PBAP (Phone
Book Access Profile) and MAP (Message
A ccess Profile), the following contacts and
messages are downloaded into COMAND
when connecting:
Rphone book
Rcall lists
Rtext messages
Further information on the conditions for con-
necting (
Ypage 382).
Telephone383
COMAND
Z

list. In this case, start a new search to
update the Bluetooth®telephone list.
Authorizing (registering) a mobile phone
Passkey entry
Telephone basic menu
Option 1: using the passkey (access code)
XSelect the mobile phone using the Ï
symbol in the Bluetooth®telephone list by
turning cVdthe COMAND controller and
press Wto confirm.
The input menu for the passkey appears.
The passkey is any one to sixteen-digit num-
ber combination which you can choose your-
self. You must enter the same number com-
bination in COMAND and in the Bluetooth
®-
capable mobile phone (see the mobile phone
operating instructions).
iSome mobile phones require a passkey
with four or more digits.
iIf you want to reauthorize a mobile phone
following deauthorization, you can select a
different passkey.
iMercedes-Benz recommends de-authori-
zation in COMAND and on the mobile
phone (
Ypage 387). Subsequent authori-
zation may otherwise fail.
XTo enter the passkey in COMAND: press
the number keys one after the other.
or
XSelect the digits in the digit bar one by one
by turning cVdthe COMAND controller
and press Wto confirm.
¬ is highlighted after the first number
has been entered.
XIn both cases, select ¬and press Wto
confirm.
XTo enter the passkey on the mobile
phone: if the Bluetooth®connection is suc-
cessful, you will be requested to enter the
passkey (access code, passcode; see the
mobile phone operating instructions).
XEnter the same passkey in the mobile
phone as the one already entered in
COMAND.
The Connecting Bluetooth Pro‐
files...message appears.
The Authorization successful
mes-
sage appears once authorization is com-
pleted.
The mobile phone is connected to COMAND
(authorized). You can now make phone calls
using the COMAND hands-free system.
iAfter entering the passkey, you may also
need to enter a confirmation in your mobile
phone to connect calls. Please check your
mobile phone display. On some mobile
phones, this confirmation can be saved. In
this case, you do not need to enter it again.
If the COMAND display shows the Author‐
ization failedmessage, you may have
exceeded the prescribed time period.
Repeat the procedure.
Telephone385
COMAND
Z

Option 2: use Secure Simple Pairing
The mobile phone (or the Bluetooth
®audio
device) must support the Bluetooth®version
2.1 for connection via Secure Simple Pairing.
COMAND creates a six-digit code, which is
displayed on both devices that are to be con-
nected.
XIf the code is the same on both devices,
confirm Yes
by pressing W.
If you select Yes
, authorization is continued
and the mobile phone is connected.
If you select No
, the process will be can-
celed.
XConfirm the message on the mobile phone.
External authorization
If COMAND does not detect your mobile
phone, this may be due to particular security
settings on your mobile phone. In this case,
you can test if your mobile phone can find
COMAND. The Bluetooth
®device name for
COMAND is MB Bluetooth
.
Please note the following: some mobile
phones require that you establish the con- nection to COMAND again once you have
entered the passkey (see the mobile phone
operating instructions). The mobile phone
cannot otherwise be authorized.
XPress the
%function button on
COMAND.
XSelect Connect Devicefrom the tele-
phone basic menu by sliding VÆand turn-
ing cVdthe COMAND controller and
press Wto confirm.
The Bluetooth
®telephone list appears.
XSelect Connect via Phoneand press W
to confirm.
The message on the left appears.
XStart the Bluetooth®search on the mobile
phone; see the mobile phone operating
instructions.
XSelect COMAND (MB Bluetooth) on the
mobile phone.
XOption 1: when requested to do so, enter
the passkey first on the mobile phone and
then in COMAND.
XOption 2: confirm the displayed codes on
the mobile phone and in COMAND (Secure
Simple Pairing).
With both options, you see the prompt Do
you want to be
authorized?on the COMAND display.
XIf you selectYes, the mobile phone will be
authorized. The messages Waiting for
a Connection to// dev.>…andConnecting Bluetooth
Profiles...are displayed. If the connec-
tion is successful, you see the telephone
basic menu and the connected mobile
phone is entered.
If you select No
, the process will be can-
celed.
Switching between mobile phones
If you have authorized more than one mobile
phone, you can switch between the individual
phones.
XSelect the mobile phone in the Bluetooth®
telephone list by turning cVdthe
386Telephone
COMAND

COMAND controller and pressWto con-
firm.
The selected mobile phone is searched for
and connected if it iswithin Bluetooth
®
range and ifBluetooth®is activated.
Only one mobile phone can beconnected
at any one time. The currently connected
mob ilephone isindicated bythe #dot in
the Bluetooth
®telephones list.
iYou can only switch to another authorized
mob ilephone ifyou are not currently mak-
ing a call.
De-authorizing (de-registering) a mobile
phone
Mercedes-Benz USA, LLC recommends de-
authorization in COMAND and on the mobile
phone. Subsequent authorization may other-
wise fail.
XPress the %function button on
COMAND.
XSe lect Connect Devicefrom the tele-
phone basic menu by sliding VÆand turn-
ing cVdthe COMAND controller and
press Wto confirm.
The Bluetooth
®telephone list appears
(
Ypage 384).
XSelect the desired mobile phone in the
Bluetooth®telephones list.
XSelect the list symbol to the right of the
entry by sliding VYthe COMAND control-
ler and press Wto confirm.
XSelect Deleteand press Wto confirm.
A prompt appears asking whether you
really wish to deauthorize this device.
XSelect YesorNo.
If you select Yes
, the device will be deleted
from the Bluetooth®telephones list.
If you select No
, the process will be can-
celed.
iBefore re-authorizing the mobile phone,
you should also delete the device name MB
Bluetoothfrom your mobile phone's Blue-
tooth®list.
Displaying connection details
XPress the %function button on
COMAND.
XSelect Connect Dev.from the telephone
basic menu by sliding VÆand turning
cVd the COMAND controller and press W
to confirm.
The Bluetooth
®telephone list appears.
XSelect the desired mobile phone in the
Bluetooth®telephones list.
XSelect the list symbol to the right of the
entry by sliding VYthe COMAND control-
ler and press Wto confirm.
XSelect Detailsand press Wto confirm.
The following information concerning the
selected mobile phone is shown:
RBluetooth®name
RBluetooth®address
Ravailability status (shown after a new
search)
Rauthorization status
XTo close the detailed view: turncVd or
slide XVY the COMAND controller.
Telephone basic menu (Bluetooth®
interface)
Basic menu display
Telephone basic menu (Bluetooth®interface)
:
Telephone status
;Signal strength of mobile phone network
Ä
=Receiver icon ¢or¡
Telephone387
COMAND
Z

?To display call lists
ACharacter bar
BBluetooth®name of the currently connec-
ted mobile phone
CTo display the COMAND phone book
XPress the %function button.
When the connected mobile phone is ready
for use, the telephone basic menu appears.
iDisplay ;may vary, depending on the
mobile phone connected.
Bars ;show the current signal strength of
the mobile phone network. If all bars are
filled, you have optimum reception.
If no bars are shown, reception is either
very poor or there is none at all.
Receiver icon shows whether a call is
active/being connected ¡or not ¢.
Text message display in the telephone
basic menu
The Text Message
menu item is only availa-
ble if the Bluetooth®phone supports the MAP
Bluetooth®profile ( Message AccessProfile).
The downloading of text messages from the
Bluetooth
®phone must have been comple-
ted. The menu item is otherwise grayed out.
Further information on text messages
(
Ypage 400).
If you have an unread text message, the 1
mail symbol is displayed. The symbol disap-
pears once you have read the text message.
The ú mail symbol is displayed as soon as
the text message memory is full. The symbol
disappears once you delete at least one text
message.
Reception and transmission volume
Once the mobile phone has been authorized,
you can optimize the transmission and recep-
tion volume settings. Find out more about the
optimum settings for your mobile phone
online at http://www.mbusa-mobile.com .
Or call the Mercedes-Benz Customer Assis-
tance center at 1-800-FOR-MERCedes (1-800-367-6372) (USA) or Customer Rela-
tions at 1-800-387-0100 (Canada).
XPress the
%function button.
XSelect Connect Dev.in the telephone
basic menu by sliding VÆand turning
cVd the COMAND controller and press W
to confirm.
XSelect an authorized mobile phone from
the list by turning cVd.
XSelect the list symbol to the right of the
entry by sliding VYthe COMAND control-
ler and press Wto confirm.
XSelect Reception VolumeorTransmis‐
sion Volumeand press Wto confirm.
XSelect a volume setting by turning cVdthe
COMAND controller.
XTo close the setting scale: pressWor
slide XVY .
iIncorrect settings may have an impact on
the quality of calls.
388Telephone
COMAND

Using the telephone
Incoming call
Accepting a call
Example: incoming call
XTo accept: confirmAcceptby pressing W.
or
XPress the 6button on COMAND or on
the multifunction steering wheel.
iYou can also accept the call by voice com-
mand using the Voice Control System (see
the separate operating instructions).
Once you have accepted the call, you can use
hands-free mode.
The call volume can be adjusted
(
Ypage 298).
Other functions during a call (
Ypage 390)
If the phone number of the caller is transfer-
red, it appears in the display.
If an entry for the caller exists in the phone
book, you will also see the name.
If the phone number is not transferred or the
"Hide data" function is activated, Unknown
appears in the display.
iYou can also accept a call as described
above when another main function is
switched on in COMAND. Once you have
accepted the call, the display switches to
the telephone display. After the call is fin-
ished, you see the display of the previous
main application again. The display does not switch to telephone
mode if you:
Rpress the
%back button next to the
COMAND controller and then
Raccept the call using the 6button on
the multifunction steering wheel
Rejecting a call
XTo reject: selectRejectby turning cVd
the COMAND controller and press Wto
confirm.
or
XPress the ~button on COMAND or on
the multifunction steering wheel.
Making a call
Using the number keypad
XCall up the telephone basic menu
(
Ypage 387).
XEnter the digits using the number keypad.
XTo connect the call: press the6but-
ton on COMAND or on the multifunction
steering wheel.
Using the telephone basic menu
XCall up the telephone basic menu
(
Ypage 387).
XSelect the digits one by one by turning cVd
and sliding ZVÆthe COMAND controller
and press Wto confirm.
XTo make a call: select°in the character
bar and press Wto confirm.
or
XPress the 6button on COMAND or on
the multifunction steering wheel.
Telephone389
COMAND
Z