2016 MAZDA MODEL CX-5 lights

Black plate (193,1)
With auto-light control
Switch Position
Ignition Position ONACC or
OFFONACC or
OFFONACC or
OFFONACC or
OFF
Headlights Off Off Auto
*1Off Off Off On Off
Daytime running lights On*2Off Auto*1Off On*2Off Off Off
Taillights
Parking lights
License lights
Side-marker lights
Dashboard illuminationOff Off Auto
*1Off/On*3On On OnOff/On*3
*1 The headlight and other light settings switch automatically depending on the surrounding brightness detected
by the sensor.
*2 It turns on while driving the vehicle.
*3 While the lights are turned on, they will remain on even if the ignition is switched to a position other than ON.
If the driver's door is opened or 30 s have elapsed with the lights turned on, the lights turn off.
When Driving
Switches and Controls
4-59
CX-5_8DV2-EA-14K_Edition3 Page193
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K

Black plate (194,1)
Auto-light control
When the headlight switch is in the
position and the ignition is switched ON, the
light sensor senses the surrounding lightness or darkness and automatically turns the
headlights, other exterior lights and dashboard illumination on or off (see chart above).
CAUTION
ØDo not shade the light sensor by adhering a sticker or a label on the windshield.
Otherwise the light sensor will not operate correctly.
ØThe light sensor also works as a rain sensor for the auto-wiper control. Keep
hands and scrapers clear of the windshield when the wiper lever is in the
position and the ignition is switched ON as fingers could be pinched or the wipers
and wiper blades damaged when the wipers activate automatically. If you are
going to clean the windshield, be sure the wipers are turned off completely―this
is particularly important when clearing ice and snow―when it is particularly
tempting to leave the engine running.
NOTE
lThe headlights, other exterior lights and dashboard illumination may not turn off immediately
even if the surrounding area becomes well-lit because the light sensor determines that it is
nighttime if the surrounding area is continuously dark for several minutes such as inside long
tunnels, traffic jams inside tunnels, or in indoor parking lots.
In this case, the lights turn off if the light switch is turned to the
position.lThe dashboard illumination can be adjusted by rotating the knob in the instrument cluster. Also,
the day/night mode can be changed by rotating the knob until a beep sound is heard. To adjust the
brightness of the dashboard illumination:
Refer to Dashboard Illumination on page 4-14.
lThe sensitivity of the AUTO lights may be changed.
Refer to Personalization Features on page 9-10.
4-60
When Driving
Switches and Controls
CX-5_8DV2-EA-14K_Edition3 Page194
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K

Black plate (195,1)
qHeadlight High-Low Beam
Press the lever forward to turn on the high
beams.
Pull the lever back to its original position
for the low beams.
The headlight high-beam indicator light in
the instrument cluster illuminates while
the high beams are turned on.
High beam
Low beam
qFlashing the Headlights
Can be used when the ignition is switched
ON.
To flash the headlights, pull the lever fully
towards you (the headlight switch does
not need to be on). The headlight high-
beam indicator light in the instrument
cluster illuminates simultaneously. The
lever will return to the normal position
when released.
OFF
Flashing
qComing Home Light System
The coming home light system turns on
the headlights (low beams) when the lever
is operated.
To turn on the system
When the lever is pulled with the ignition
switched to ACC or OFF, the low beam
headlights turn on.
The headlights turn off after a certain
period of time has elapsed after the doors
are closed.
NOTElThe time until the headlights turn off after
all of the doors are closed can be changed.
Refer to Personalization Features on page
9-10.
lIf no operations are done for 3 minutes
after the lever is pulled, the headlights turn
off.
lThe headlights turn off if the lever is pulled
again while the headlights are illuminated.
When Driving
Switches and Controls
4-61
CX-5_8DV2-EA-14K_Edition3 Page195
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K

Black plate (196,1)
qLeaving Home Light System
The leaving home light system turns on
the lights when the key unlock button is
pressed while away from the vehicle.
To turn on the system
When the ignition switch and the
headlight switch are as indicated below,
the lights will illuminate when the
transmitter unlock button is pressed and
the vehicle receives the transmitter signal.
The lights turn off after a certain period of
time has elapsed (30 seconds).
lIgnition switch: offlHeadlight switch:or
The following lights turn on when the
leaving home light system is operated.
Low beams, Parking lights, Taillights,
License lights
Unlock button
Lock button
NOTElOperation of the leaving home light system
can be turned on or off.
Refer to Personalization Features on page
9-10.
lWhen the transmitter lock button is pressed
and the vehicle receives the transmitter
signal, the lights turn off.
lWhen the headlight switch is in a position
other than
or, the lights turn off.
qHeadlight Levelingí
The number of passengers and weight of
cargo in the luggage compartment change
the angle of the headlights.
The angle of the headlights will be
automatically adjusted when turning on
the headlights.
A system malfunction or operation
conditions are indicated by a warning.
Refer to Warning/Indicator Lights on page
4-20.
qDaytime Running Lights
Some countries require moving vehicles
to have their lights on (daytime running
lights) during the daytime.
The daytime running lights turn on
automatically when the vehicle starts
moving.
They turn off when the parking brake is
operated or the shift lever is shifted to the
P position (automatic transaxle vehicle).
NOTE
(Except Canada)
The daytime running lights can be deactivated.
Refer to Personalization Features on page
9-10.
4-62
When Driving
íSome models.
Switches and Controls
CX-5_8DV2-EA-14K_Edition3 Page196
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K

Black plate (197,1)
Fog Lightsí
Can be used when the ignition is switched
ON.
Use this switch to turn on the fog lights.
The fog lights will improve visibility at
night and during foggy conditions.
To turn the fog lights on, rotate the fog
light switch to the
position.
The headlight switch must be in the
position before turning on the fog lights.
Fog light switch
To turn the fog lights off, rotate the fog
light switch to the
position or turn
the headlight switch to the
or
position.
NOTE
lThe fog lights will turn off when the
headlights are set at high beams.
l(With auto-light control)
If the fog light switch is in the
position
and the headlight switch is in the
position, the fog lights will turn on when
the headlights, the exterior lights and
dashboard illumination turn on.
Turn and Lane-Change
Signals
NOTElIf an indicator light flashes abnormally, one
of the turn signal bulbs may be burned out.
lA personalized function is available to
change the turn indicator sound volume.
Refer to Personalization Features on page
9-10.
qTurn Signals
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.
If the indicator light continues to flash
after a turn, manually return the lever to
its original position.
Right turn
Left turn Right lane change
Left lane changeOFF
Green indicators on the dashboard show
which signal is working.
qLane-Change Signals
Move the lever halfway toward the
direction of the change―until the
indicator flashes―and hold it there. It
will return to the off position when
released.
When Driving
Switches and Controls
4-63íSome models. CX-5_8DV2-EA-14K_Edition3 Page197
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K

Black plate (204,1)
Horn
To sound the horn, press themark on
the steering wheel.
Hazard Warning Flasher
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.
The hazard warning lights warn other
drivers that your vehicle is a traffic hazard
and that they must take extreme caution
when near it.
Depress the hazard warning flasher switch
and all the turn signals will flash. The
hazard warning indicator lights in the
instrument cluster flash simultaneously.
NOTE
lThe turn signals do not work when the
hazard warning lights are on.
lCheck local regulations about the use of
hazard warning lights while the vehicle is
being towed to verify that it is not in
violation of the law.
4-70
When Driving
Switches and Controls
CX-5_8DV2-EA-14K_Edition3 Page204
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K

Black plate (206,1)
lVerify that there is a remote control
transmitter available for the device you
would like to program.
lDisconnect the power to the device.
qProgramming the HomeLink System
CAUTION
When programming a garage door
opener or a gate, disconnect the
power to these devices before
performing programming, as
continuous operation of the devices
could damage the motor.
The HomeLink system provides 3 buttons
which can be individually selected and
programmed using the transmitters for
current, on-market devices as follows:
1. Position the end of your hand-held
transmitter 2.5―7.5 cm (1―3 inches)
away from the HomeLink button you
wish to program while keeping the
indicator light in view.
2. Simultaneously press and hold both the
chosen HomeLink and hand-held
transmitter buttons.Do not release the
buttons until step 3 has been
completed.
NOTE
Some gate operators and garage door openers
may require you to replace this Programming
Step 2 with procedures noted in the“Gate
Operator/Canadian Programming”section.
3. After the HomeLink indicator light
changes from a slow to a rapidly
blinking light, release both the
HomeLink and hand-held transmitter
buttons.NOTE
If the HomeLink indicator light does not
change to a rapidly blinking light, contact
HomeLink atwww.homelink.comor call1-
800-355-3515for assistance.
4. Firmly press and hold the programmed
HomeLink button for five seconds, and
then release it. Perform this operation
two times to activate the door. If the
door does not activate, press and hold
the just-trained HomeLink button and
observe the indicator light.
If the indicator lightstays on constantly,
programming is completeand your
device should activate when the
HomeLink button is pressed and released.
NOTE
To program the remaining two HomeLink
buttons, begin with“Programming”―step 1.
If the indicator light blinksrapidly for
two seconds and then turns to a
constant light, continue with
“Programming”steps 5―7to complete
the programming of a rolling code
equipped device (most commonly a
garage door opener).
5. At the garage door opener receiver
(motor-head unit) in the garage, locate
the“learn”or“smart”button. This can
usually be found where the hanging
antenna wire is attached to the motor-
head unit.
6. Firmly press and release the“learn”or
“smart”button. (The name and color of
the button may vary by manufacturer.)
NOTE
Complete the programming within 30 seconds.
4-72
When Driving
Switches and Controls
CX-5_8DV2-EA-14K_Edition3 Page206
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K

Black plate (210,1)
NOTElThe electric parking brake cannot be
applied or released while the vehicle
battery is dead.
lIf the electric parking brake is repeatedly
applied and released it may stop operating
to prevent overheating of the motor. If this
occurs, wait approx. 1 minute before
operating the electric parking brake switch
again.
lAn operation sound occurs when applying
or releasing the electric parking brake,
however, this does not indicate a
malfunction.
lIf the electric parking brake is not used for
long periods, an automatic inspection of the
system is performed while the vehicle is
parked. An operation sound can be heard,
however, this does not indicate a problem.
lWhen the electric parking brake is applied
and the ignition is switched OFF, an
operation sound can be heard, however,
this does not indicate a problem.
lThe brake pedal may move while the
electric parking brake is being applied or
released, however, this does not indicate a
problem.
lIf the electric parking brake switch is
continually pulled while driving the vehicle,
the electric parking brake will be applied
and the electric parking brake warning
beep will be activated. When the switch is
released, the electric parking brake is
released and the beep stops.
lIf the electric parking brake is applied with
the ignition switched off or in ACC, the
brake system warning light in the
instrument cluster and the indicator light in
the switch may turn on for 15 seconds.
lWhen running the vehicle through an
automatic car wash, it may be necessary to
switch the ignition off with the parking
brake released depending on the type of
automatic car wash.
When applying the electric parking
brake
The electric parking brake can be applied
regardless of the ignition switch position.
Securely depress the brake pedal and pull
up the electric parking brake switch.
The electric parking brake is applied and
the brake system warning light and the
electric parking brake switch indicator
light turn on.
Refer to Warning/Indicator Lights on page
4-20.
When releasing the electric parking
brake
The electric parking brake can be released
while the ignition is switched ON or the
engine is running. When the electric
parking brake is released, the brake
system warning light and the electric
parking brake switch indicator light turn
off.
4-76
When Driving
Brake
CX-5_8DV2-EA-14K_Edition3 Page210
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K