2016 Hyundai Santa Fe display

TrafficThere are three kinds of screen menus.
TMC
Change the TMC (Traffic Message
Channel) to “Off”, “Auto” or “On”.
- Auto: When the TMC event is found
on current route, the naviga-
tion system searches the detour
route automatically without any
announcement.
- Off: Cancels the TMC function.
- On: When the TMC event is found on
current route, the navigation sys-
tem displays the pop-up screen
of the event information.
Automatic TMC Station
When the TMC event is found on cur-
rent route, the strongest TMC station is
received automatically.
Favourite TMC Station
The unit receives the TMC station that
the user set. This is activated when you
cancel the [Automatic TMC Station].NavigationThere are four kinds of screen menus.
Motorway Junction View
This displays the motorway junction on
the map screen.
Enhanced Lane Guidance
This displays the enhanced lane on the
map screen.
Plan Different Routes
This displays the plan different routes
on the map screen.
Speed Alert
This displays the speed alert on the
map screen.AudioThere are five kinds of screen menus.
SDVC (Speed Dependent Volume Control)
When the speed of your vehicle is more
than 40 km/h, the volume level outputs
higher than original volume level.
You can set the SDVC to Off, Low, Mid
(Middle), or High.
- Off: Outputs the original volume
level regardless of the speed of your
vehicle.
- Low, Mid, High: This outputs auto-
matically the volume level according
to the speed of your vehicle.
Navigation Volume
You can set or cancel the voice
announcement for navigation. Even
though the setting is "Off", when start-
ing new route guidance, it is set to "On"
automatically.
Touchscreen Click
You can set the touchscreen sound to
On/Off.
18
Setup

Sound (Default : Center)
- Balance: Touch
b or B to adjust the
sound the left and right speakers.
- Fader: Touch
v or V to adjust the
sound of the front and rear speakers.
- Bass, Mid, Treble: Touch
b or B to
adjust the Bass, Middle or Treble.
Note
Touch [Center] to return to the default
settings.
Power BassYou can set the Power Bass to Off, Low,
Mid (Middle), or High.
- Off: Outputs the original sound.
- Low, Mid, High: Set the Low, Mid
(Middle), or High to
boost the low-pitched
sound.
DisplayThere are two kinds of screen menus.
Brightness
You can set the brightness of the
screen.
Set the display brightness to Low, Mid
(Middle), or High.Map Mode
To improve the visibility of the map
screen between day and night, you can
change the combination of the colours
of the map.
- Auto: The map screen is displayed by
autolight signal or illumination
signal.
- Day: The map screen is always
displayed with bright colours.
- Night: The map screen is always
displayed with dark colours.
19
Setup
Balance/
FaderBass/
Middle/
Treble
Autolight Off
(Day)
Autolight On
(Night)
Autolight is
not detected
Illumination
On
Map: Day
Map: Night
Map: NightIllumination
Off
Map: Day
Map: Night
Map: Day

What is GPS?The Global Positioning System (GPS)
is a satellite-based navigation system
made up of a network of 24 satel-
lites placed into orbit by the U.S.
Department of Defense.
GPS was originally intended for military
applications, but in the 1980s, the gov-
ernment made the system available for
civilian use.
GPS works in any weather conditions,
anywhere in the world, 24 hours a day.
There are no subscription fees or setup
charges to use GPS.
About satellite signals
Your unit must acquire satellite signals
to operate. If you are indoors, near
tall buildings or trees, or in a parking
garage, the unit cannot acquire satel-
lites.
Acquiring satellite signals
Before the unit can find your current
location and navigate a route, you must
do the following steps:
1. Go outside to an area free from tall
obstructions.
2.
Turn on the unit.
Acquiring satellite signals can take a
few minutes.
Initial navigation screen
After the ignition switch is placed in the
ACC or ON position, when you enter
a navigation mode for the first time,
the caution screen is displayed on the
screen. Read the caution carefully and
then touch [Agree].
Indicators of the map screen
How to view a map screen
The navigation system displays various
information on the screen.
•
/
Indicates the direction of the map.
Touch to switch the orientation of the
map.
•
Indicates the current vehicle location
and the direction of travel.
•
Touch [Menu] to access the map
menu.
20
Getting started with navigation
GPSGPSGPS
GPS

Near Position
1. Press [NAV] > Touch [POI] > [Near
Position].
2. Touch one of the subcategory.
(For example: Emergency)
3. Touch one of the subcategory in next
level. (For example: Hospital)
4. Touch the preferred POI.5. Touch [OK] after confirming the
location of the displayed POI.
If you want to call on the telephone,
touch [
]. It is available only when
the bluetooth is active.
6. Touch [Start].
7. Touch the preferred route.8. Touch [Start].
Drive in accordance with the screen
and voice information.
25
Destination input menu

Near Destination
1. Press [NAV] > Touch [POI] > [Near
Destination].
2. Follow steps 2-8 on the page 25
(Near Position).
In City
1. Press [NAV] > Touch [POI] > [In Cit y].
2. Set the part characters of city name
and then touch [OK].
3. Touch the city in the list.
4. Follow steps 2-8 on the page 25
(Near Position).
Name
1. Press [NAV] > Touch [POI] > [Name].
2. Set the preferred country.
3. Input the part characters of the
facility name and then touch [OK].
4. Follow steps 4-8 on the page 25
(Near Position).
Hyundai service
1. Press [NAV] > Touch [POI] > [Hyundai
service].
2. Follow steps 4-8 on the page 25
(Near Position).
Note
The information of position may dif-
fer from actual location due to some
changes of dealership and dealer loca-
tion information.
Phone Number
1. Press [NAV] > Touch [POI] > [Phone
Number].
2. Input the phone number and then
touch [OK].
3. Touch the preferred phone number
from the list.
4. Touch [OK] after confirming the
location of the displayed POI.
If you want to call on the telephone,
touch [
]. It is available only when
the bluetooth is active.
5. Follow steps 6-8 on the page 25
(Near Position).
26
Destination input menu

Tour Planner
The tour planner allows you to travel
through the searched routes by setting
a destination or way point.
You can set a total of 4 destination or
way point.
- New Tour: Sets a tour.
- Load Tour: Displays the tourist.
- Show Tour: Displays tourist set lastly.
Setting a tour
1. Press [NAV] > Touch [Advanced] >
[Tour Planner].
2. Touch [New Tour].
3. Touch [Yes].4. Set a destination by using the navi-
gation menu.
(Refer to the page 22.)
The destination you set is displayed.
5. Touch [Add Tourpoint].
6. Set a way point by using the
[Navigation], [Advanced], and
[Favourites] menu.
(Refer to the page 22.) If you need an additional way point, set
it by touching [Add Tourpoint] again.
7. Touch [Start].
If you would like to save the
searched routes, touch [Yes].
Otherwise, touch [No].
8. Input a name, then touch [OK].
The searched routes are stored in
the [Load Tour] automatically.
9. Drive in accordance with the screen
and voice information.
29
Destination input menu

POI Category
Some landmarks in the surrounding
area can be displayed as icons on the
screen.
This allows you to display or hide the
landmark icons by type.
1. Press [MAP] > Touch [Menu] >
[View] > [POI Category].
2. Touch the desired icons.
The icon display settings toggle on
and off each time you touch the
icon. The indicator of the selected
icon illuminates.3. Touch [OK].
The activated landmark icons are
displayed on the map.
2D/ 3D
The map view can be changed between
2D and 3D.
- 2D: Displays the map in a 2-dimen-
sional environment similar to a
road map.
- 3D: Displays the view from an elevated
perspective. It is easy to recognize
an image of the route because it
provides a panoramic view over a
long distance.
1. Press [MAP] > Touch [Menu] >
[View] > [2D/3D].
2. Touch [2D/3D] again to switch to
the 2D screen.
34
Using the map menu

Route Options
You can modify the route conditions or
confirm the route information. Set the
appropriate route condition according
to your purpose.
1. Press [MAP] > Touch [Menu] >
[Route] > [Route Options].
2. Touch the preferred setting item.
• Route: If you don’t set the [Plan
Different Routes] in the
setup menu, set the route
option to Fast (
), Short
(
) or Eco ().
Note
• Fast Route: Calculates a route with
the shortest travel time.
• Short Route: Calculates a route
with the shortest distance.
•
Eco (Economical) Route:
- To save fuel consumption, this
route considers to reduce the
number of frequent stop&go
route at the intersection and turn-ing point based on fuel consump-
tion table with real time traffic
information, however this route
may not be valid in terms of driv-
ing conditions such as sudden
acceleration.
- Eco Route might have more driv-
ing time and distance to save fuel
consumption.

• TMC:
- Auto (
): When the TMC event
is found on current
route, the navigation
system searches the
detour route auto-
matically without any
announcement.
- Off (
): Cancels the TMC func-
tion.
- On (
): When the TMC event is
found on current route,
the navigation system
displays the pop-up
screen of the event
information.
Note
A pay TMC is not supported. • Toll Road (
)
- Use: Includes the use of toll
roads.
- Avoid: Enables the avoid of toll
roads.
• Tunnel (
)
- Use: Includes the use of tunnel.
- Avoid: Enables the avoid of tun-
nel.
• Main Road (
)
- Use: Includes the use of main
road.
- Avoid: Enables the avoid of main
road.
• Ferry (
)
- Use: Includes the use of ferries.
- Avoid: Enables the avoid of fer-
ries.
3. Press [OK].
When the current location map
screen or route setting screen is
displayed, the system recalculates a
route with the set conditions.
Note
• Always stop the vehicle in a safe local
before modifying the route conditions.
•
Modifying the route conditions while
driving may cause an accident.
36
Using the map menu