2016 Citroen BERLINGO MULTISPACE key

 147
Berlingo-2-VP_en_Chap05_Securite_ed01-2016
 147
CHILD LOCK
This prevents opening of the siding
side  doors   from   the   inside.
Manual Electric
With the ignition on, press
this
  button   in   the   middle   of  
the

  dashboard.
Indicator
  lamp   on   =   child   lock  
on.
Please

 
note:   this   system   is  
independent

  of   the   central   locking  
control.Always

  remove   the   ignition   key  
when leaving the vehicle, even for
a

 
short   time.
It
 
is
 
advisable   to   check   the   state   of  
the

 
child
 
lock   each   time   the   ignition   is  
switched

  on.
In
 
the
 
event   of   a   serious   impact   the  
electric

 
child   lock   is   deactivated  
automatically

.
a label indicates the position of the
lever

 
and
 
the
 
state
 
of
 
the
 
child
 
lock.
-
o
pen fully past the point of
resistance.
-

T

ilt the lever, located on the rear
section
 
of
 
the
 
door.
SaFETY
5
Child safety

150
Towing a trailer
Berlingo-2-VP_en_Chap06_accessoire_ed01-2016
TOWBAR WITH SWAN NECK T
OWBALL ,
LOCKABLE

AND
QUICKL
Y
DET

ACHABLE
Presentation
This swan neck towbar, delivered assembled,   can   be   removed   and   fitted  
easily

.   No   tools   are   needed.
Instructions for fitting and before
every use
Check
  that   the   swan   neck   is   correctly  
locked

  by   verifying   the   following   points:
-
 
the
  green   mark   on   the   locking  
wheel is visible,
-

 
the
  safety   lock   on   the   locking   wheel  
is directed toward the rear

,
-
 
the
  safety   lock   is   closed   and   the  
key

  removed;   the   locking   wheel   can  
no longer be operated,
-

 
the
  swan   neck   must   no   longer  
move

  at   all   in   its   carrier.
When
  hooking   up   the   trailer,   don't  
forget

  to   connect   the   trailer   harness.
Fitting

158
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Levels
Cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When
  the   engine   is   warm,   the  
temperature

  of   the   coolant   is   controlled  
by

  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and

  because   the   cooling   system   is  
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has

  dropped,   remove   the   cap   and   top  
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this

  indicates   a   fault   which   must   be  
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes
  as   soon   as   possible,   when  
traffic

  conditions   permit   (until   the  
message

  disappears   and   the   service  
warning

  lamp   goes   off).
d

uring regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating

  may   be   heard   under   the  
dashboard.
If

  the   message   is   still   displayed   and  
if

  the   service   warning   lamp   remains  
on, contact a CITR

o Ë n dealer or a
qualified
  workshop.
Topping up
The
 
level
 
must
 
be
 
between
 
the
 
MIN
 
and

 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required to top up the level, have the
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash and headlamp
wash level
For best quality cleaning and for your
safety, we would advise that you use
products   of   the   CITROËN   range.
For
  optimum   cleaning   and   to   avoid  
freezing,

  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
If
  your   vehicle   is   fitted   with   headlamp  
washers, the capacity of the reservoir
is

  6   litres.
Diesel additive level
(Diesel with particle
filter)
Topping up
This   additive   must   be   topped   up   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
avoid prolonged contact of used oil
with   the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITR

o Ë n dealer (France) or
an
  authorised   waste   disposal   site.
The
 
minimum
 
level
 
of
 
this
 
additive
 
is indicated by lighting of the service
warning

 
lamp,
 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
screen.
When this occurs with the engine
running it is due to the start of
saturation

 
of
 
the
 
particle
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).

161
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Fuel
REFUELLING
Low fuel level
Filling
The  fuel   tank   must   be   filled   with
the
engine off.
-
 
Open
  the   fuel   filler   flap.
-
 
Insert
  the   key,   then   turn   it   a   quarter  
turn.
-

 
Remove
  the   cap   and   hook   it   onto  
the clip located on the inside of the
flap.
When

  filling   with   fuel,  
a mechanical

  system   prevents  
opening

  of   the   left-hand   side   door.  
When

  the   fuel   filler   flap   is   open,   ensure  
that

  no   one   tries   to   slide   this   door.
Once
  the   flap   has   been   closed,   the  
sliding

  side   door   may   jam,   push   the  
door

  to   close   it   then   open   it.
When the low fuel level is
reached,
 
this
 
warning
 
lamp
 
comes

 
on. A
 

label   affixed   to   the   inside   of   the   flap  
reminds

  you   of   the   type   of   fuel   to   be  
used.
Y

ou   must   fill   with   at   least   5   litres   of   fuel  
for

  it   to   be   registered   by   the   fuel   gauge.
When
  the   fuel   filler   cap   is   opened,  
there

  may   be   a   slight   inrush   of   air.  
This
 
vacuum

  is   entirely   normal   and   is   due   to  
the

  sealing   of   the   fuel   system.
When
  filling   the   fuel   tank,   do   not  
continue after the 3rd cut-off of the
nozzle.
 This
 
could
 
cause   malfunctions.
The
 
capacity
 
of
 
the
 
fuel   tank   is  
approximately

 
60
 
litres.
-
 
After

 
filling
 
the
 
fuel   tank,   lock   the  
cap

 
and
 
close
 
the   flap.
Fuel used for petrol
engines
The petrol engines are compatible with E10 bio-petrol (containing 10 %
ethanol),   conforming   to   European  
standards

  EN   228   and   EN   15376.
E85 type fuels (containing up to 85 %
ethanol) are reserved exclusively for
vehicles
  marketed   for   the   use   of   this  
type

  of   fuel   (BioFlex   vehicles).  
The
 
quality

  of   the   ethanol   must   comply   with  
European

  standard   EN   15293.
You then have approximately 8 litres
of
 
fuel
 
remaining.
Fill up without delay to avoid running
out
 
of
 
fuel.
Never
 
risk
 
driving
 
until
 
you
 
run
 
out
 
of
 
fuel

 
as
 
this
 
may
 
damage
 
the
 
emissions
 
control

 
and
 
injection
 
systems.
CHECkS
7

DIESEL
162
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Fuel
FUEL CUT- OFF
In a serious collision, a mechanism automatically
  prevents   fuel   from  
reaching

  the   engine.
The
  flashing   of   this   warning  
lamp

  is   accompanied   by   a  
message

  in   the   screen.
Check
  that   there   is   no   odour   or  
leakage

  of   fuel   outside   the   vehicle   and  
re-establish

  the   fuel   supply:
-

switch of
f the ignition
(ST
o

P

position),
-
 
remove
  the   key,
-
 
put
  the   key   back   in   the   ignition,
-
 
switch
  on   the   ignition   and   start.
DIESEL PRIMING
PUMP
Fuel used for Diesel

engines
The Diesel  engines  are  compatible  with  biofuels
  available   at   the   pumps   which  
meet

  current   and   future   European  
standards:
-

 
Diesel
  fuel   that   meets   standard  
EN 590

  mixed   with   a   biofuel   that  
meets

  standard   EN   14214,
-
 
Diesel
  fuel   that   meets   standard  
EN16734

  mixed   with   a   biofuel   that  
meets

  standard   EN14214   (possibly  
containing up to 10 % Fatty a

cid
Methyl Ester),
-
 
Paraffinic
  Diesel   fuel   that   meets  
standard

  EN15940   mixed   with  
a

  biofuel   that   meets   standard  
E

n 14214 (possibly containing up to
7
  %   Fatty  
Acid
  Methyl   Ester).
The
  use   of   B20   or   B30   fuel   meeting  
standard

  EN16709   is   possible   in  
your

  Diesel   engines.   However,   this  
use, even occasional, requires strict
application of the special servicing
conditions referred to as "

a rduous
conditions".
  For   more   information,  
contact a CITR

o Ë n dealer or a
qualified
  workshop. If you run out of fuel, it is necessary to
prime
  the   fuel   circuit.
Other HDi engines
- Fill
  the   fuel   tank   with   at   least   five  litres
  of   Diesel.
-
 
Squeeze
  and   release   the   manual  
priming

  pump,   under   the   bonnet,  
under

  the   protective   cover.
-
o perate the starter until the engine
starts.
BlueHDi engine
- Fill   the   fuel   tank   with   at   least   five  litres
  of   Diesel.
-

Switch on the ignition (without
starting

  the   engine).
-

W
ait around 6 seconds and switch
off
  the   ignition.
-
 
Repeat
  the   operation   10   times.
-
o perate the starter to run the
engine.
The use of any other type of (bio)
fuel
 
(vegetable
 
or
 
animal
 
oils,
 
pure
 
or

 
diluted,
 
domestic
 
fuel...)
 
is
 
strictly
 
prohibited

 
(risk
 
of
 
damage
 
to
 
the
 
engine

 
and
 
fuel
 
system).
o

nly the use of
d
iesel fuel additives
that
 
meet
 
the
 
standard
 
B715000
 
is
 
authorised.

170
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
ECONOMY MODE
after the engine has stopped, with
the   key   in   the   ignition   position,   certain  
functions (windscreen wiper

, electric
windows,
  courtesy   lamps,   audio  
equipment,

  etc.)   can   only   be   used   for   a  
cumulative

  duration   of   thirty   minutes,   to  
prevent

  discharging   of   the   battery.
Once
  the   thirty   minutes   have   elapsed,  
the active functions are put on standby
and

  the   battery   warning   lamp   flashes  
accompanied

  by   a   message   in   the  
screen.
T

o   resume   the   use   of   these   functions  
immediately

,   start   the   engine   and   let   it  
run

  for   a   few   minutes.
The
  time   available   will   then   be   double  
the

  time   for   which   the   engine   was   left  
running.

  However,   this   time   will   always  
be

  between   five   and   thirty   minutes.
A
 

flat   battery   will   prevent   the  
engine

  from   starting.
Battery

Audio and Telematics
 227
Berlingo-2-VP_en_Chap10a_SMEGplus_ed01-2016
Select a radio station or frequency (refer to the
corresponding section). Press on Radio Media
to display the
primary pag e.
Press
  on   the   secondary   page.
Select " Settings ".
Select " Radio".
Activate/deactivate
 " R

DS
options ".
Press on Radio Media
to display the
primary
 pag

e.
Press
 
on
 
the
 
secondary
 
page. Press on "
Save"
  (preset).
Select
  a   number   in   the   list   to   preset   the  
p

reviously   chosen   radio   station.
A
  long   press   on   a   number   saves   (presets)   the  
s

tation.
Press on Frequency
.
Enter the frequency in full
(e.g.: 92.10 MHz)
 
using
 
the
 
keypad
 
t

hen " Confirm ".
Changing radio station
Pressing
 
the
 
name
 
of
 
the
 
current
 
radio
 
station
 
b

rings
 
up
 
a
 
list.
To
 
change
 
radio
 
station
 
press
 
the
 
name
 
of
 
the
 
de

sired
 s

tation.
o
r Press on Radio Media to display the
primary
 pag

e.
Select " Save"
  (preset).
Presetting a station Activating / Deactivating RDS
OR
THEN
a

press on this button presets all of
the
  stations   one   after   the   other.
Recalling preset stations
RdS, if activated, allows you to continue
listening  to   the   same   station   by   automatic r

etuning   to   alternative   frequencies.
 H

owever, in certain conditions, coverage
of
  an   RDS   station   may   not   be   assured
 t

hroughout the entire country as radio
stations do not cover 100 % of the
territory.
  This   explains   the   loss   of
 r

eception   of   the   station   during   a   journey.
TECHNOLOGY on BOARD
10

Audio and Telematics
253
Berlingo-2-VP_en_Chap10a_SMEGplus_ed01-2016
Level 1Level 2 Level 3 Comments
Connected services Apple
® CarPlay®
Telephone Favourites
The   "Telephone"   function   is   placed   automatically  i
n   "Siri"   voice   mode.
Press on "di splay contacts" for access to the
telephone
 me

nus.
Calls
Contacts
Keypad
Messages
Music Lists
Press
  on   "Music"   to   browse   and   select   the   tracks  
o

n   your   smartphone.
Press
  on   "Playing"   for   access   to   the   track  
c

urrently   playing.
Artists
Tr a c k s
Albums
Other...
Plan DestinationsPress on "
de

stinations" to search for an address
by
  "Siri"   voice   command   or   by   using   the   keypad.
The GPS function is through the telephone's 3G,
4G
  or   Wi-Fi   internet   connection.
Messages Display messagesThe
  "Messages"   function   is   place   automatically  
i

n   "Siri"   voice   mode   to   speak   the   message   and  
t

he
 a
ddressee.
Press
  on   "Display   messages"   for   access   to   the  
m

essages.
Playing Access
  to   the   track   currently   playing.
TECHNOLOGY on BOARD
10