2016 AUDI S8 warning

Operating noi se
Noises may occur when braki ng depend ing on the
speed, braking force and outside cond itions s uch
as temperature and humidity.
Due to the na ture of t he mate ria ls used in ce ram­
ic bra ke rotors*, noises m ay become mo re appa­
ren t at low speeds.
Effect of wat er and road salt
In ce rtain situat ions, for example after driving
through water, in heavy ra in, afte r ove rnig ht con­
densat ion or after washing your car, the braking
effe ct can be red uced by moisture or ice on the
b rake rotors and brake pads. The brakes must be
dried first w ith a few careful brake applications .
At highe r speeds and with t he windsh ie ld wipers
turned o n, the bra ke pads p ress against the bra ke
rotors for a short amount of time . This occ urs at
regular intervals without the driver noticing and
provides for better bra ke response time under
wet conditions.
The effectiveness of the brakes can be reduced
when the vehicle is dr iven on a salt-covered road
and the brakes are not used. L ikewise, you clean
off accumu lated salt coat ing from brake discs
and pads with a few cautious applications of the
brake
c::> ,& .
Due to their sur face characteristics, ceramic
brake rotors* absorb mo isture in such condit ions.
This can cause a temporary reduction in braking
force compared to dry brakes. You can compen­
sate for this by pressing the brake peda l harder.
Cor rosion
There may be a tendency for dirt to b uild up on
the brake pads and corros ion to form on the discs
if the car is not driven regularly or only for short
tr ips with little use of the brakes.
If the brakes are not used frequently, or if corro­
sion has formed on the discs, it is adv isable to
clean off the pads and discs by brak ing firmly a
few t imes from a moderately high speed
c::> ,& .
Sma rt Technology
Faults in the brake system
If you s hou ld notice a sudden increase in br ake
peda l travel, then one of the two bra ke circu its
may have fai led
c::> ,& .
Low brake fluid level
Malfunctions ca n occu r in the brake system if the
brake fluid level is too low . T he brake flu id leve l
is monitored elect ronically.
Brake boost er
The brake booster works w ith vacuum pressure
wh ich is created only when the engine is runn ing
c::> ,& .
Brake lining wear status
Brake lining wear may be checked by visua l in­
spect ion of the cond ition of the brake pads
t hr ough the openings in the wheel. If necessary,
the wheel may be removed for t his inspection
c::> page 259, Replacing wheels .
.8_ WARNING
-New b rake p ads don't h ave the bes t stop­
p ing power an d must be "broken-in" during
the initial 250 miles (400 km) . The break-in
pe riod can be considerably longer for
veh icles with ceramic brake rotors*. You can
compensate for this by pressing the brake
pedal more firmly. This also applies late r
when new pads are installed.
- You shou ld perform braking maneuvers for
the purpose of cleaning the brake system only i f road co ndit ions pe rmit . Other road
users m ust not be put at r is k -you may
cause an ac cident!
- Before descending a steep g rade, reduce
speed and sh ift transmission into a lower
gear o r lower dr iving range. Do not r ide the
b ra kes or hold the pe dal down too long or
too often. This cou ld cause the b rakes to ge t
hot and dimin ish b raking effic iency .
- Do not " ride the bra kes" by rest ing you r foot
on the pedal when you do no t intend to
brake. This may cause the brakes to over­
heat, premature wear and increased stop­
p ing distance.
193

Smart Techn olo gy
- Under certain climatic and operating condi­
tions such as passing through water, driving
in heavy rain or after washing the vehicle,
the effectiveness of the brakes can be re­
duced . In w inter, ice can accumulate on the
brake pads, linings, discs and drums . Care­
fully apply brakes fo r a tes t. Brakes w ill dry
and ice coatings wi ll be cleaned off after a
few careful brake applications .
- Driving for an extended pe riod of time on
salt-covered roads witho ut using your
brakes can also affect bra king efficiency.
Clean off accumulated salt coating from
brake discs and pads with a few carefu l
brake applications.
- If you damage the front spoiler, or if you in­
stall a different spoiler, be sure the air flow
to the front brakes is not obstructed. Other­
wise the brake system could overheat reduc­
ing the effectiveness of the entire brake sys­
tem.
- Failure of one brake circuit will impair the
braking capability result ing in an increased
stopp ing distance. Avoid driving the vehicle
and have it towed to the nea rest Aud i dealer
or qualified workshop.
- Never let the vehicle roll to a stop with the
engine shut off.
- If the brake booster is not working, the
brake pedal must be pressed considerably
harder to make up for the lac k of booster
assistance.
Electromechanical power
assist, dynamic steering
The electromechanical power assist helps the
driver when steering.
Power steering adapts electronically based on
the vehicle speed.
Ind icator light s and messages
• Stee ring defective! St op th e ve hicle
If th is ind icator light turns on and stays on and
this message appears, the power steer ing may
have fa iled.
194
Do not continue driving. See your authorized
Audi dealer or other qualified repair facility for
ass istance .
,Ion Steering : System faul t You can c ontinue
dri ving
If the indicato r light turns on and the message
appears, the steeri ng may be more diff icult to
move o r more sensitive than usu a l. T he steer ing
whee l may also be at an angle when driving
straight.
D rive slowly to your a uth orized Aud i dea ler or
qualified wo rkshop to have the malfunct ion cor­
rected.
1;r,ij D ynamic steering : Init ializing
If this driver message appears and the indicator
light is flashing on the instrument panel, dynam­
i c steer ing* is being re initialized . After starting
the engine, t he steering wheel w ill move slightly.
Re- initializa tion might be necessary if the steer­
i ng whee l was moved hard to the left and right
while the vehicle was not moving . The display
goes out as soon as initialization is comp lete .
D rive slowly to your a uth orized Aud i dea ler or
qualified wo rkshop to have the mal func tion cor­
rected.
.&_ WARNING
Have the dynamic steering * system malfunc­
tion repaired as soon as possible by an au­
thorized Audi dealer or qualif ied workshop -
risk of acc ident!
(D Tips
If the . or ,Ion indicator light only stays on
for a short time, you may continue driving.
- The dynamic steering* stabi lity systems are
not ava ilable in the event of a system mal­
function.
- For additiona l information on dynamic
steering *, refer to~
page 106 .

Driving with your
quattro
With All Wh eel Drive , all four wh eels are driven .
General information
With All W heel Drive, power is dis tribute d to all
four wheels . This happens automatically depend­
ing on your dr iving style and the road conditions
at the time . See also¢
page 190 . With the sport
d ifferent ial*, power d istr ibution to the rear
wheels is variable and can be adjusted with Audi
d rive select*
¢ page 106. Always read and fo llow
safety preca utio ns ¢ ,&. .
Winter tires
When drivi ng in the w inter, you r vehicle with All
Wheel Drive has an advantage, even with reg ular
tires. In winter road cond itions it may be adv isa­
b le to mount w inte r tir es (or a ll-season tires) for
i mproved d riveab ility and bra king : these tires
must be mounted on
all four wheels . See also
¢ page 251, W inter tires.
Snow chains
Where snow chains are mandatory on certain
roads, this normally also a pplies to vehicles w it h
All Whee l Dr ive ¢
page 251, Snow chains.
Replacing wheels /tires
Veh icles w ith All Wheel Drive must always have
tires of the same s ize. A lso avo id tires wi th d iffer­
ent tread depths. For detai ls see page
¢ page 243.
Off-Road driving?
Your Aud i does not have e nough g round clear­
a nce to be used as an off-road vehicle . It is there­
fore best to avoid rough tracks and uneve n ter­
r ain as m uch as possible . Also refe r to
¢page 197.
_& WARNING ,~ -
Always adjust you r driv ing to road and t raffic
conditions . Do not let the extra safety affo rd­
ed by All Wheel Drive tempt you into taking
extra risks.
Sma rt Technology
- Although the A ll Whee l Drive is very effec­
tive, always remember that braking capacity
is limited by t ire tract ion. You shou ld there­
fore not dr ive at excessive speeds on icy or
slippe ry road surfaces .
- On wet road surfaces, be careful not to dr ive
too fast because the front wheels could be­
g in to slide on top of the water (aquap la n­
ing) . If th is should oc cur, you will have no
warn ing from a sudden increase in engine
speed as with a front-wheel d rive vehicle.
Always d rive at speeds which are suited to
the road conditions -risk of c rash.
Energy management
Starting ability is optimized
Energy management controls the distribution of
electrical energy and thus op timizes the availa­
bility of electrical energy for starting the engine .
If a vehicle with a conventional energy system is
not driven for a long pe riod of time, the battery is
discharged by id ling curre nt consumers (e.g. im­
mobilize r) . In certain circumstances i t can resu lt
in t he re being i nsufficien t energy ava ilable to
sta rt the engine.
Intelligent energy manageme nt in you r vehicle
hand les the distribution of electrical energy .
Start ing ability is markedly improved and the life
of the ba ttery is ex tended.
Bas ica lly, energy management cons ists of
bat ­
tery diagnosis , idling current management
and
dynamic energy management .
Battery diagnosis
Battery d iagnosis continuously dete rm ines the
state of the battery. Sensors determine battery
vo ltage, battery current and battery tempera­
tu re. This de termines the current state o f ch arge
and the power of the battery .
Idling current management
Idling current management reduces energy con­
sumption while the vehicle is standing. With the ..,_
195

Driving and the
environment
Breaking in
New eng ine
The engine needs to be run-in during the first
1,000 miles (1 ,500 km).
For the first 600 miles (1 ,000 kilometers):
"' Do not use full throttle .
"' Do not drive at engine speeds that are more
than 2/3 of the max imum permitted RPM .
"' Avoid high eng ine speeds.
From 600 to 1 ,000 miles (1,000 to 1,500
kilometers ):
"' Speeds can gradually be increased to the maxi­
mum pe rm issib le road or e ngine speed.
During and after b reak-in period
"' Do not rev the engine up to high speeds when it
is cold . This applies whether the transmission is
in N (Neutral) or in gear .
After the bre ak-in period
"' Do not exceed maximum engine speed under
any circumstances .
"' Upshift into the nex t higher gear
before reach­
ing the red area at the end of the tachometer
sca le
c:::;, page 10.
During the first few hours of driving , the eng ine's
internal friction is higher than later when all the
mov ing parts have been broke n in. How well this
b reak-in process is done depends to a considera­
b le exte nt o n the way the veh icle is d rive n du ring
the first 1,0 00 miles (1,500 kilome ters).
(D Note
E xtremely high eng ine speeds a re au toma ti­
cally reduced. However, t hese rpm li mits are
p rogr amme d fo r an eng ine well run-in, not a
new engine .
Driving and the envir onment
{® For the sake of the environment
Do not drive with unnecessarily high engine
spe eds -upshifting early saves fuel, red uces
no ise and protects the environment.
New tires
If your vehicle is runni ng on new tires, drive par­
t icularly careful for the first 3S0 m iles (500 kilo ­
meters) after fitting .
_&. WARNING
New tires tend to be slippe ry and mus t also
b e "bro ken- in". Be sure to remembe r th is dur­
i ng the first 350 m iles ( 500 k ilome ters).
Brake gent ly . Avoid following closely behin d
other vehicles or other s ituations that might
require sudden, hard braking.
Avoid damaging the
vehicle
When you are dr iv ing on poor roads, or over
curbs, steep ramps, etc., make certai n that low ­
ly ing parts such as spo ile rs and exhaust system
parts do not bottom o ut and get damaged .
This is espec ially true for veh icles with low-s lung
chass is (sports c hass is)* and fully loaded
vehicles .
Catalytic converter
Applies to: vehicles with gasoline engine
It is very important that your emission control
system (catalytic converter) is functioning prop ­
erly to ensure that y our vehicle is running in an
environmen tally sound manner.
"' Always use lead-free gasoline c:::;, page 212,
F uel supply .
"' Never run t he tank down all the way to emp ty.
"' Never put too much motor o il in yo ur engine
c:::;, page 225, Adding engine oil ce:r..
"' Never try to push- or tow-start your vehicle.
T he ca talytic co nverter is an efficient "cle an-up"
device built into the exhaust sys tem o f th e vehi -
-
cle. The catalytic converter b urns many of the .,.
197

Driving and th e en vironm ent
pollutants in the exha ust gas before they are re ­
leased into the atmosphere.
The exclusive use of unleaded fue l is critica lly im­
portant for the l ife of the catalytic converter and
proper functioning of the engine.
A WARNING
T he temperature of the exha ust system is
high, both when driving and after stopping
the engine.
-
- Never touch the exhaust tail pipes once they
have become hot. This could result in burns.
- Do not park or operate the vehicle in areas
where the hot exha ust system may come in
contact with dry grass, brush, fue l spill or
other mater ial which can cause a fire.
- Do not apply additional undercoating or rustproofing on or near the exhaust mani­
fold, exhaust p ipes, catalytic converter or
heat sh ields. During dr iv ing, the substance
used fo r undercoating could overheat and
ca use a fire.
(D Note
- Be aware that just one tank filling with
le aded fuel will already ser iously degrade
the performance of the catalytic co nverter .
- Do not exceed the correct eng ine oil level
<=;> page 225.
-Do not drive until the fuel tank becomes
complete ly empty. The engine could mis­
fire. Unburned fuel could also get into the
exhaust system and this cou ld cause the
cataly tic converte r to overheat.
- Do not sw itch off the ignition while the veh i­
cle is moving.
- Do not continue to operate your vehicle un­
der these cond it ions, as otherwise fue l can
r each the catalyti c converte r. This cou ld re­
su lt in overheating of the conve rter, req uir­
i ng its replacement.
- T o assure efficient oper ation of the Emis­
s ion Control Sys tem:
- Have your veh icle maintained properly and
in accordance with the service recommen­
dations in your Warranty
& Maintenance
book let .
198
-Lack of proper ma intenance as well as im ­
proper use of the vehicle wi ll impair the
funct ion o f the emission control system
and could lead to damage.
@ For the sake of the environment
Even when the Emiss ion Control System is op ­
erating properly, the exhaust gas can have a
su lfu r-li ke exhaust gas sme ll under some op­
erating states. Th is depends on the sulfur
content of the fuel being used. Us ing a d iffer­
ent brand of fuel may help, or fi lling the tank
with lead-free super g rade gasoline.
Diesel particulate filter
App lies to: vehicles with diese l engine
The diesel particulate filter filters nearly all of
the soot part icles out of the exhaus t. The filte r
clea ns itself automat ica lly unde r no rma l dr iv ing
cond it ions. If the fil ter canno t clean i tself (fo r ex­
amp le, because yo u are on ly driving short distan­
ces), the filter becomes clogged with soot and
the
II symbol for the diese l particu late filter il­
l uminates
¢ page 20.
A WARNING
- Do not park your vehicle over flammable
materials such as grass or leaves because
the high temperature of the diesel particu­
la te filte r could sta rt a fi re.
-
- Do not apply an underbody protectant in the
exhaust system area or a fire could start.
Shutting down vehicle
If you would like your vehicle to remain inopera­
tive for a longer period of time, contact an Audi
or other spec ia lized dealer . They can adv ise you
o n necessary p recautions e .g. corros ion preven­
tion, ma intenance and storage . Pay attention to
additional informat ion concer ning t he battery.
Refer to
<::;> page 2 31.

Driving through water on
roads
Note the following to avoid vehicle damage when
driving through water, for example on flooded
roads:
- The water must not be any higher than the bot­
tom of the vehicle body.
- Do not drive faster than wa lking speed.
A WARNING
After driving through water, mud, slush, etc.,
the brakes may be slow to take effect because
of wet brake rotors and pads . Dry the brakes
first by brak ing carefully to restore the full
brak ing effect.
([) Note
-Vehicle components such as the engine,
transm ission, suspension or electrical sys ­
tem can be severely damaged by driving
th rough water.
- Always switch off the Sta rt-Stop-System*
whe n driving through water¢
page 85 .
(D Tips
-Check the depth of the water before driving
through it.
- Do not stop the veh icle, dr ive in reverse or
switch the eng ine off when dr iving through
wa ter .
- Keep in mind that oncoming ve hicles may
create waves that raise the water level and
make it too deep for your vehicle to drive
th rough safely.
- Avo id driving through salt water because it
can cause corrosion.
Driving and the envir onment
Economical and environ­
mentally-friendly driving
General
Your personal style of driving will determine the
economy of your vehicle, as well as exhaust and
nois e levels .
Fuel economy, e nv ir onmental impact, and wear
o n your eng ine, brakes and tires large ly depend
on three factors:
- your personal driving style
- operat ing cond itions
- technical limitations
If you anticipate what you need to do next and
drive economically, you can easily cut your fuel
consumption by 10-15 percent. Th is section will
give you some tips on how you can help the envi­
ronment and your pocketbook .
(D Tips
The consumption estimates as published by
ENVIRONMENTAL PROTECTION AGENCY
(EPA) and Transport Canada may not corre­
spond to your actual consumption on the
r oad, which w ill vary depending upon vehicle
l oad and speed, road and weather conditions,
trip length , etc.
Drive smoothly and keep a lookout ahead
Vehicles use the most fuel when they are acceler­
ating.
.,. Avoid unnecessary accelerat ing and braking .
Vehicles use the most fuel when they are acceler­ at ing . If you anticipate what is going to happen
next, you w ill need to brake less and, thus, accel­
erate less. Let the vehicle coast whenever possi­
ble - for example when you see that the next traf­
fic lig ht is red.
199

Trail er mode
Trailer mode
Driving with a trailer
General information
Your Audi was designed primarily for passenger
transportation.
If you plan to tow a trailer, please remember that
the additional load will affect durability, econo­
my and performance.
Trailer towing not only places more stress on the
vehicle, it also calls for more concentration from the driver.
For this reason, always follow the operating and
driving instructions provided and use common
sense.
(D Note
If you are going to tow a trailer, you must ac­
tivate the trai ler operation mode
¢ page 202, Operating instructions.
Technical requirements
Tr ailer hitch
Use a weight-carrying hitch conforming to the
gross trailer weight. The hitch must be suitable
for your veh icle and trailer and must be mounted
securely on the vehicle's chassis at a
technically
sound
location . Use only a trailer hitch with a re­
movable ball mount . Always check w ith the t rail­
er h itch man ufact urer to make sure that you are
using the co rrect hitc h.
Do not u se a bumper hitch .
The hitch must be installed in such a way that it
does not interfere with the impact-absorbing
bumper system . No mod ificat ions should be
made to the vehicle exhaust and brake systems .
F rom t ime to t ime, check that a ll hitch mo unt ing
bolts rema in securely fastened.
When you are not tow ing a traile r, remove the
tra iler hitch ball mount. This prevents the hitch
from caus ing damage should your vehicle be
struck from behind
¢ ,&. .
202
Trailer b rakes
If your trailer is equipped with a braking system,
check to be sure that it co nforms to all regu la­
tions.
The tra iler hydrau lic brake system must not be
directly connected to the vehicle's hydrau lic
brake system .
Safety chains
Always use safety chains between your vehicle
and the tra iler.
Trailer light s
Trailer lights must meet all regulations. Be sure
to check with your Aud i dealer for correct wir ing,
switches and relays .
Mirror s
If you are unable to see the traffic behind you us­
ing the regular outside mirrors, then you
must in­
stall extended mirrors . It is important that you
always have clear vision to the rear.
A WARNING
Afte r remov ing the tra iler hitch, do not sto re
i t in you r vehicle. In case of s udden braking,
the hitch could fly fo rwa rd and injure you or
your passengers.
Operating instructions
Fig. 1 87 MMI d ispl ay: tow ing mode o n
Maximum traile r weight
A tra iler for your vehicle is lim ited to a typical
class 1 or class 2 trailer.

Trailer mod e
conditions are unfavorable - particularly when
going downhill.
Red uce veh icle speed
imm ediatel y if the tra ile r
shows the s lightest sign of swaying.
Do not try
to stop the sway in g b y accele rating .
Observe speed lim its . In some areas, speeds for
ve hicl es towing tra ilers are lower than for reg ula r
veh icles.
A lways apply brakes early . When dr iving down­
h ill , sh ift into a lower gear to use the engine
b raking effect to slow the veh icle. Use of the
brakes a lone can cause them to overheat and fail.
Air suspension*
When driving with a tra iler, activate the trailer
mode of the air suspension . Switch the air sus­
pens ion tra iler mode on when you a re towing a
tra ile r. This will limit the regulat ion by the air
suspens ion while driving . Select in the MM I:
ICARI function button > (Car )* sys tem s control
button >
Vehicle setting s > Air su sp .: to wi ng >
On .
Coolant temperature
The coolan t temperature gauge¢ page 10 must
be observed carefully. The coo lant temperature
can increase if you drive on long inclines in a low
gear at high engine speeds. Reduce your speed
immed iate ly if the LEDs in the top part of the dis­
p lay turn on.
For more information about indicator lights, re­
fer to.
¢page 15.
A WARNING
Anyone not properly restrained in a moving
vehicle is at a much greater risk in an acci­
dent. Never let anyone ride in your car who is
not properly wearing the restraints provided
by Audi.
Trailer mode notes
Important to know
Your vehicle hand les different ly when towing a
trai ler because of the additiona l weight and dif­
ferent weight distr ibut ion. Safety, performance
204
-
and economy will g reatly depend on how carefu l­
l y you load your trai ler and operate your rig .
Befo re yo u actually tow yo ur t railer, pract ice
turning, stopping and backing up in an area away
from traffic. Keep practicing unti l you have be ­
come complete ly familiar with the way your vehi­
cle-tra iler combination behaves and responds .
Backing up is diff icult and requ ires practice.
Backing up with a trailer genera lly req uires steer ­
ing action opposite to that when backing up your
vehicle witho ut a trailer .
Maintain a greater distance between yo ur vehicle
and the one in front of you. You will need more
room to stop . To compensate for the trailer, you
will need a larger than normal turning radius .
When passing, remember tha t you canno t accel­
erate as fast as you normally wou ld because of
the added load . Make sure you have enough room
to pass. After passing, allow p lenty of room for
your trailer before changing lanes again.
Avoid jerky starts, sharp turns or rapid lane changes.
(D Tips
- Do not tow a trailer du ring the break-i n pe ri­
od of your vehicle.
- If you tow a tr aile r, your A udi may requi re
more frequent ma intenance due to the ex­
tra load ¢
page 281.
Parking on a slope
Do not park on a slope with a trailer . If it cannot
be avoided, do so only after doing the following:
When parking:
.,. App ly the foot brake.
.,. Have someone p lace chocks unde r both the ve­
hicle and the trailer wheels .
.,. With chocks in place, slowly release the brakes
until the wheel chocks abso rb the load .
.,. Turn the whee ls towards the curb.
.,. App ly the parking brake .
.,. Select the P selector lever posit ion.