2016 AUDI Q5 tow

,....,
N
co
er::
co
,...., (D Note
Special care is required if you are repairing
the tire on a steep incline.
@ Tips
- Do not operate the compressor for more
than 12 minutes continuously, otherwise it
can overheat. Once the compressor has
cooled, you can continue to use it.
- If sealant has spi lled out, let it dry and then
you can remove it by peeling it away like a
foil.
- Remember to obtain a new bott le of sealant
from your authorized Audi dealer after re­
pair ing a tire. After this, the functionality of
the tire repair set is restored .
- Obey all laws.
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel.
""After you experience a tire failure, pull the car
well away from moving traff ic and try to reach
level ground before you stop¢_& .
.. All passengers sho uld
leave the car and move
to a safe location (fo r instance, behind the
guardrai l) ¢ .&_ .
.. Engage the
par king b rake to prevent yo ur vehi ­
cle from roll ing unintentionally ¢&_ .
.. Move
selecto r le ver to po sitio n P ¢ &_ .
"" If you are towing a trailer: unh itch the trailer
from your veh icle.
"" Block the diagonally opposite wheel with the
folding chocks o r other objects .
""T ake the
jac k* and the inflatable spa re tir e*
out of the luggage compartment ¢ page 254 .
A WARNING
You or your passengers cou ld be inj ured while
changing a wheel if you do not follow these
safety precautions:
- If you have a flat tire, move a safe distance
off the road. Turn off the engine, turn the
Em ergenc y ass is tanc e
emergency flashers on and use other wa rn­
ing dev ices to alert other motorists.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traff ic.
- To help prevent the veh icle from moving
suddenly and possib ly slipping off the jack*,
always fully set the parking brake and block
the wheel diagonally opposite the wheel be­ i n g changed with the fold ing c hocks or oth­
er objects . When one front whee l is lifted
off the ground, placing the Automatic
Transmission in P (Park) w ill
not prevent the
veh icle from moving.
- Before you change a wheel, be sure the
gro und is leve l and firm.
If necessary, use a
sturdy board under the jack*.
- Always s tore the vehicle too l kit, the jack*
and the replaced tire in the lugg age com­
partment
¢ page 139.
Changing a wheel
When you change a wheel, follow the sequence
described below s tep-by -step and in exactly that
order.
1. Remove the de corative wheel cover* . For
more detai ls see also¢
page 260, Decaro-
tive wheel covers
o r¢ page 260, Wheels
with wheel bolt cops .
2. Loosen the w
heel bolt s ¢ page 260.
3 . Locate the proper mounting point for the
jack* and align the jack* below that point
¢ page 261.
4. Li ft the car with the jack*¢ page 261 .
s. Remove the wheel with th e flat tire and then
insta ll the
inflatable spar e tir e *
¢ page 262.
6. Tighte n all whee l bolts lightly.
7 .
Lo wer the vehicle wi th the jack *.
8 . Use the whee
l bolt wrench and
firml y tighten
all wheel bo lts ¢
page 260 .
9. Replace the decorat ive wheel co ver* .
259
...

Emergency situations
Emergency situations
General
This chapter is intended for trained emergency crews and working personnel who have the nec­
essary tools and equipment to perform these
operations.
Starting by pushing or
towing
CD Note
Vehicles with an automatic transmission
cannot be started by pushing or towing.
Starting with jumper
cables
If necessary, the engin e con be started by con­
necting it to the battery of another vehicle.
If the engine should fail to start because of a dis­
charged or weak battery, the battery can be con­
nected to the battery of
another vehicle, using a
pair of jumper cables to start the engine.
Jumper cables
Use only jumper cables of sufficiently large cross
section
to carry the starter current safely. Refer
to the manufacturer's specifications.
Use only jumper cables with
insulated terminal
clamps which are distinctly marked :
plus(+) cable in most cases colored red
minus(-) cable
in most cases colored black.
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal in­
jury. Follow the instructions below for
safe
handling of your vehicle's battery.
-Always shield your eyes and avoid leaning
over the battery whenever possible.
-A discharged battery can freeze at tempera­
tures just below 32 °F (0 °C). Before con­
necting a jumper cable, you must thaw the
270
frozen battery completely, otherwise it could explode.
- Do not allow battery acid to contact eyes or
skin. Flush any contacted area with water immediately.
- Improper use of a booster battery to start a
vehicle may cause an explosion.
- Vehicle batteries generate explosive gases.
Keep sparks, flame and lighted cigarettes
away from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery.
- The voltage of the booster battery must also
have a 12-Volt rating. The capacity (Ah) of
the booster battery should not be lower
than that of the discharged battery. Use of
batteries of different voltage or substantial­
ly different "Ah" rating may cause an explo­
sion and personal injury.
- Never charge a frozen battery. Gas trapped in the ice may cause an explosion.
- Never charge or use a battery that has been
frozen . The battery
case may have be weak­
ened .
- Use of batteries of different voltage or sub­
stantially different capacity (Ah) rating may
cause an explosion and injury. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
~page 220.
CD Note
-Applying a higher voltage booster battery
will cause expensive damage to sensitive
electronic components, such as control
units, relays, radio, etc.
- There must be no electrical contact between
the vehicles as otherwise current could al­
ready start to flow as soon as the positive
(+) terminals are connected.
@ Tips
- The discharged battery must be properly
connected to the vehicle's electrical system. .,..

Emergency situations
-When connecting jumper cables, make sure
that they cannot get caught in any moving
parts in the engine compartment.
- Do not bend over the batteries -danger of
chemical burns!
- The battery cell locking screws must be
tightened securely.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c> page 220.
(D Note
Improper hook-up of jumper cables can ruin
the generator .
- Always connect POSITIVE(+) to POSITIVE
(+), and NEGATIVE(-) to NEGATIVE(-)
ground post of the battery manager control
unit.
- Check that all screw p lugs on the battery
cells are screwed in firmly. If not, tighten
plugs prior to connect ing clamp on negative
battery terminal.
- Please note that the procedure for connect ­
i ng a jumper cable as described above ap­
plies specifically to the case of your vehicle
being jump started . When you are giving a
ju mp start to another vehicle , do
not con­
nect the negative (-) cable to the negative
(-) terminal on the discharged batte ry @
c> fig. 228. Instead, securely connect the
negative( -) cab le to either a solid metal
component that is firm ly bolted to the en­
gine block or to the engine block itself. If
the battery that is being charged does not
vent to the outside, escap ing battery gas
could ignite and explode !
Towing with a tow truck
General hints
Your Audi requires special handling for towing.
The following information is to be used by com ­
mercial tow truck operators who know how to op­
erate the ir equipment safely.
-Never tow your Audi, towing will cause dam­
age to the engine and transmission.
272
-Never wrap the safety chains or winch cables
around the brake lines .
- To prevent unnecessary damage, your Audi
must be transported with a flat bed truck .
- To load the vehicle on to the flat bed, use the
towing loop found in the vehicle tools and at­
tach to the front or rear anchorage
i:>pag e 272 and i:> page 273.
A WARNING
A vehicle being towed is not safe for passen­
gers . Never allow anyone to ride in a vehicle
being towed, for any reason.
Front towing loop
Do not install the front towing loop until it is
needed.

Fig. 229 Front bumper : remov ing the cover cap

Fig. 230 Front bumper: s crew ing in t he towing loop
The towing loop fits into the threaded hole locat­
ed on the right side o f the front bumper and cov­
ered by a cover when not in use.
.,. Remove the towing loop from the vehicle tool­
kit
c> page 254 .
.,. Carefully remove the cove r c> fig. 229.
.,. Screw the towing loop tightly into the threaded
hole as far as it will go
c> fig. 230. Ill>

..... N
co ~ CX)
..... I.Cl U"I
..... I.Cl .....
When it is no longer needed, unscrew the towing
loop and put it back into the vehicle toolkit. Be
sure to have the towing loop stored in the vehicle
at all times.
When r e-installing the cover be sure to first in ­
sert the tabs on the cover into the retainers near
the radiator grille. Then install the other side of
the cover and push it into the retainers
¢fig. 229.
The appearance of the cover varies from the i llus­
tration for some model vers ions.
.&_ WARNING
If the towing loop is not screwed in as far as it
will go, the thread can pull out when the vehi­
cle is towed -potential risk of an accident.
(D Note
The cover is attached to the bumper with sev­
eral hooks. Do not use excessive force when
removing the cover to avoid damag ing it.
Rear towing loop
On vehicles without a factory-installed trailer
hitch*, the threaded hole for the towing loop is
on the right side of the rear bumper.
Fig. 231 Rear bumper: Cover
Emergency situations
Fig. 232 Rear bumper: Screw ing in towing loop
Vehicles with a towing loop
.,. Remove the towing loop from the vehicle tool­
kit
c;, page 254.
.,. Press the cover in by applying short stro ng
press ure to release it from the bumper
¢fig. 231 .
.,. Screw the towing loop tightly into the threaded
hole as far as it will go
c;, fig. 232.
Vehicles with a trailer hitch*
.,. Insta ll the trailer hitch.
.,. Atta ch the towing bar or the towing cable to
the trailer hitch.
Unscrew the towing loop again after use and in­
stall the cover in the bumper . Ret urn the towing
loop to the vehicle toolkit. Be sure to have the
towing loop stored in the vehicle at all times.
A WARNING
-If the towing loop is not screwed in as far as
it will go, the thread can pull out when the
vehicle is towed - potential risk of an acci­
dent.
- If your vehicle has a
trailer hitch* only use a
special towing bar to prevent damaging the
ball hitch. These tow ing bars have been spe­
cially designed for trailer tow ing hitches.
- If your vehicle has a
trailer hitch* use only
special towing cables .
273

Emergency situations
Loading the vehicle onto a flat bed truck
Fig. 233 Veh icle o n flat bed truck
Front hook up
.. Align the vehicle with the centerline of the car
carr ier ramp.
.. Attach the winch hook to the front towline eye
prev iously installed.
Rear hook up
.. Align the vehicle with the centerline of the car
carrier ramp.
.. Attach the winch hook to the rear towline eye
previously installed .
@ Tips
Check carefully to make sure the hook-up is
secure before moving the car up the flatbed
truck ramp.
Raising the vehicle
Lifting with workshop hoist and with floor
jack
The vehicle may only be lifted at the lifting
points illustrated.
Fig. 234 Front lifting point
274
Fig. 235 Rear lifting point
.. Read and heed WARNING ¢ f1..
.. Locate lifting points r;!) fig. 234 and c;!) fig. 235.
.. Adjust lifting arms of workshop hoist or floor
jack to match vehicle lifting points .
.. Insert a rubber pad between the floor jack/
workshop hoist and the lifting points .
If you must lift your vehicle with a floor jack to
work underneath, be sure the vehicle is safely
supported on stands intended for this purpose .
Front lifting point
The lifting point is located on the floor pan rein­
forcement about at the same level as the jack
moun ting poin t¢
fig. 234. Do not lift the vehi­
cle at the vertical sill reinforcement.
Rear lifting point
The lifting point is located on the vertical rein­
forcement of the lower sill for the on board jack*
¢fig. 235.
Lifting with vehicle jack*
Refer to<=> page 261.
,&. WARNING
-To reduce the r isk of serious injury and vehi­
cle damage.
- Always lift the vehicle on ly at the special
workshop hoist and floor jack lift points il ­
l ustrated <=>
fig. 234 and ¢ fig. 235.
-Failure to lift the vehicle at these points
could cause the vehicle to tilt or fall from
a lift if there is a change in vehicle weight

Consumer information
Consumer information
Warranty coverages
Your Audi is covered by the following warran­
ties:
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfora-
tion
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Control Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding your warranties
can be found in your
Warranty & Maintenance
booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regulati ons in the United States and
Canada require that automobi les meet specific
emission regulations and safety standards.
Therefore, vehicles built for the U.S.A. and Cana ­
da differ from vehicles sold in other countries.
If you plan to take your vehicle outside the conti­
nenta l limits of the United States or Canada,
there is the poss ibility that:
- un leaded fue ls for vehicles with catalytic con­
verter may not be available;
- fuel may have a considerably lower octane rat­
ing . Improper fuel may cause engine damage;
- service may be inadequate due to lack of proper
service facilities, tools or testing equipment;
- r eplacement parts may not be readily available.
- Nav igation systems for veh icles built for the
U.S .A . and Canada will not necessarily work in
Europe, and may not work in other countries
outside of North America.
280
(D Note
Audi cannot be responsib le for mechanical
damage that could result from inadequate
fuel, service or parts ava ilability.
Audi Service Repair
Manuals and Literature
Audi Official Factory Service Manuals and Litera ­
ture are published as soon as poss ible after mod­
el introduction . Service Manuals and literature
are available to order from the Audi Technical Lit ­
erature Ordering Center at :
www.audi.techliterature .com
Maintenance
General '
Your vehicle has been designed to help keep
maintenance requirements to a minimum. How­
ever, a certain amount of regular maintenance is
still necessary to assure your vehicle's safety,
economy and reliability . For detailed vehicle
maintenance consult your Warranty & Mainte­
nance booklet .
Under difficult operating conditions, for exam ­
ple at extremely low outside temperatures, in
very dusty regions, when towing a trailer very fre­
quently, etc., some service work should be per­
formed between the intervals specified. This ap­
plies particularly to:
- oil changes, and
- cleaning or replac ing the a ir filter .
'
@) For the sake of the environment
By regularly maintain ing your vehicle, you
help make sure that em iss ion standards are
maintained, thus minimizing adverse effects
on the environment .
Important considerations for you and your
vehicle
The increasing use of electronics, sophisticated
fuel injection and emission control systems, and
the generally increas ing technica l complexity of ..,_

,....,
N
co
er::
co
,...., Tire Mobility System (tire repair set) . . . . . . 257
Tire pressure monitoring system
L f . oss o a,r pressure . . . . . . . . . . . . . . . . . . . 16
Tires.. .. .. .... ............. .. .. ..... 234
Low aspect ratio tires . . . . . . . . . . . . . . . . 250
Repair set . . . . . . . . . . . . . . . . . . . . . . 104, 257
Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . 259
Service life . . . . . . . . . . . . . . . . . . . . . . . . . 242
r ,re pressure . . . . . . . . . . . . . . . . . . . . . . . 244
Tire pressure monitoring system .. . 251,252
Tire pressure table . . . . . . . . . . . . . . . . . . . 245
Tread wear indicators . . . . . . . . . . . . . . . . 242
Unidirectional . . . . . . . . . . . . . . . . . . . . . . . 236
Uniform tire quality grading .... .. .. .. . 251
Tires and wheels Glossary of tire and loading termino logy . 236
Tire pressure monitoring system . . . . . . . . 16
Tires and vehicle load limits . . . . . . . . . . . 246
Tool kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Torn or frayed safety be lts . . . . . . . . . . . . . . 145
Towing Front eyelet . . . . . . . . . . . . . . . . . . . . . . . . 2 72
Rear eyelet . . . . . . . . . . . . . . . . . . . . . . . . . 273
Tow trucks . . . . . . . . . . . . . . . . . . . . . . . . . 272
Towing a trailer Parking system . . . . . . . . . . . . . . . . . . . . . . 133
T PMS (tire pressure monitoring system) . . . 252
Trailer mode . . . . . . . . . . . . . . . . . . . . . . . . . 203
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
Trailer towing Operating instructions . . . . . . . . . . . . . . . . 204
Technical requirements . . . . . . . . . . . 203 , 204
Tongue load . . . . . . . . . . . . . . . . . . . . . . . . 204
T railer turn signal assembly
Warning/indicator lights . . . . . . . . . . . . . . . 16
T ransmission
Malfunction (indicator light) . . . . . . . . . . . 126
Transport Canada . . . . . . . . . . . . . . . . . . . . . 142
Travel mode . . . . . . . . . . . . . . . . . . . . . . . . . . S4
Trip computer Fue l consumption . . . . . . . . . . . . . . . . . . . . 22
Mileage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Single-trip memory . . . . . . . . . . . . . . . . . . . 23
Total-trip memory . . . . . . . . . . . . . . . . . . . . 23
Trip odometer . . . . . . . . . . . . . . . . . . . . . . . . . 13
Index
Trunk
refer to Rear lid . . . . . . . . . . . . . . . . . . . . . . 44
T . l urn s1gna s . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Warning/indicator lights . . . . . . . . . . . . . . . 16
u
ULSD No . 2 (Diesel fuel) . . . . . . . . . . . . . . . . 214
Unfastening safety belts . . . . . . . . . . . . . . . 148
Uniform tire quality grading . . . . . . . . . . . . 251
Unlocking Power locking switch . . . . . . . . . . . . . . . . . . 42
Rear lid/trunk lid . . . . . . . . . . . . . . . . . . . . . 43
Remote contro l key . . . . . . . . . . . . . . . . . . . 40
Using the mechanical key . . . . . . . . . . . . . . 41
Use of jumper cables . . . . . . . . . . . . . . . . . . 271
V
V ·t . ani y mirror . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Vehicle Care/cleaning . . . . . . . . . . . . . . . . . . . . . . . 207
Out of service . . . . . . . . . . . . . . . . . . . . . . . 211
Transport . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Vehicle control modules . . . . . . . . . . . . . . . . 189
Vehicle identification label . . . . . . . . . . . . . 276
Vehicle Identification Number (VIN) . . . . . . 276
Vehicle jack . . . . . . . . . . . . . . . . . . . . . . 254, 261
Vehicle tool kit . . . . . . . . . . . . . . . . . . . . . . . 104
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
w
Warning/ indicator l ights
Airbag system . . . . . . . . . . . . . . . . . . . . . . . 16
Anti- lock brake system (ABS) . . . . . . . . . . . 17
Brake system . . . . . . . . . . . . . . . . . . . . . . . . 18
Cruise control . . . . . . . . . . . . . . . . . . . . . . . . 17
Electromechanical parking brake . . . . . . . . 18
Electronic power control . . . . . . . . . . . . . . . lS
Electronic Stabilization Control (ESC) . . . . . lS
Glow plug system . . . . . . . . . . . . . . . . . . . . 15
High beam . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Malfunction Ind icator Lamp (MIL) . . . . . . . 17
Safety belt . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Tire pressure monitoring system . . . . . . . . 16
Trailer turn signa l assemb ly . . . . . . . . . . . . 16
Turn signals . . . . . . . . . . . . . . . . . . . . . . . . . 16
295