,...,
N
co ~ CX) ,...,
I.Cl U"I ,...,
I.Cl ,...,
management system to enable you to use the en
ergy management functions correctly after re
placing the battery.
If it is not possible to use a battery of this type,
the new battery must have the same capacity,
voltage (12 volts), amperage, construction and
plug sealing .
When installing the battery, make sure the igni
tion and all electrical consumers are turned off.
CD Note
- Make sure the vent ilation hose on the side
of the battery is connected, otherwise
fumes or battery acid can leak out.
- Vehicles with the Start-Stop-System* are
equipped with a special cycle-proof AGM
battery. Installing a different type of bat
tery can cause prob lems in the vehicle elec
trical system. When replacing the vehicle battery, always install one with the same
spec ifications as the original battery.
@) For the sake of the environment
Because of the problem of proper disposal of
a battery, we recommend your authorized
Audi dealer change the battery for you. Bat
ter ies contain sulfuric acid and lead and must
always be disposed of properly in compliance
with all environmental regulations. Disposing
of vehicle batteries imp roperly is very danger
ous to the environment.
Windshield/headlight
washer container
Fig. 203 Engine compartment: cover on the windshield
and headl ight* washer flu id reservo ir
M N
-N
"' CX) CX)
Checking and Filling
The washer fluid container is marked with the
symbol
O on its cap ¢ fig. 203, ¢page 222,
fig. 197 .
.. Before you check anything in the engine com
pa rtment,
always read and heed all WARN
INGS ¢ A in Working in the engine compart
ment on page 220 .
.. Lift the filler cap tongue to add washer fluid .
You can fill the container to the top .
.,. Press the cap back onto the filler neck after fill-
ing the co nta iner.
You can find the reservoir
capacity in the table in
¢page 277.
Clean water should be used when filling up. If
possible, use soft water to prevent scaling on the
washer jets. Always add a glass cleaner solution
(with frost protection in the winter).
CD Note
Do not mix engine coolant antifreeze or any
other additives to fill up the windshield wash er reservoir .
233
Bead
means the part of the tire that is
made of steel wires, wrapped or
reinforced by ply cords and that is
shaped to fit the rim.
Bead separation
means a breakdown of the bond
between components in the bead.
Cord
means the strands forming the
plies in the tire.
Cold tire inflation pressure
means the tir e pressure recom
mended by the vehic le manufac
turer for a tire of a designated
size that has not been driven for
more than a couple of miles (kilo
meters) at low speeds in the
three hour period before the tire pressure is measured or adjusted .
Curb weight
means the weight of a motor ve
hicle with standard equipment in
c luding the maximum capacity of
fuel, oi l, and coolant, a ir condi
tioning and add itional weight of
optional equipment.
E xtra load ti re
means a tire designed to operate
at higher loads and at h igher in -
Wheels
flation pressures than the corre
sponding standard tire . Extra load
tires may be identified as "XL",
" xl", "EXTRA LOAD", o r "RF" on
the sidewal l.
Gross Axle Weight Rating
( " GAWR")
means the load -carrying capacity
of a single axle system, measured
at the tire-ground interfaces .
Gross Vehicle Weight Rating
("GVWR ")
means the max imum total loaded
weight of the vehic le.
Groove
means the space between two ad
jacent tr ead ribs .
Load rating (code)
means the max im um load tha t a
tire is rated to carry fo r a g iven in
flat ion pressure . You may not find
this informat ion on all tires be
cause it is not requ ired by law.
Maximum load rating
means the load rating for a tire at
the maximum pe rmissible infla
tion pressure for that tire.
Maximum loaded vehicle
weight
means the sum o f:
23 7
..
